1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining fluid, removing hoses and connectors, and taking apart components like the pump, tank, and control module.
3. The assembly procedure lists the parts and tools needed and describes reinstalling components and reconnecting hoses in reverse order of disassembly while following torque specifications.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing a lifter group on a 3176C engine. The removal process involves taking out bolts and separating the lifter assembly into sections to remove individual components like brackets, lifters and injector lifters. The installation is the reverse of removal, requiring cleaning of parts and reinstallation in the proper order and orientation. Precautions are provided to contain fluids and dispose of them according to regulations.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, seals, springs, and pistons.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. The removal procedure involves disconnecting various sensors and tubes, and removing bolts and gaskets. The installation procedure describes cleaning surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence to the correct torques. Replacing damaged threads with Heli-Coils is also described.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing a lifter group on a 3176C engine. The removal process involves taking out bolts and separating the lifter assembly into sections to remove individual components like brackets, lifters and injector lifters. The installation is the reverse of removal, requiring cleaning of parts and reinstallation in the proper order and orientation. Precautions are provided to contain fluids and dispose of them according to regulations.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, seals, springs, and pistons.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. The removal procedure involves disconnecting various sensors and tubes, and removing bolts and gaskets. The installation procedure describes cleaning surfaces, installing new gaskets and bolts, and tightening the bolts in a specific sequence to the correct torques. Replacing damaged threads with Heli-Coils is also described.
Caterpillar cat 330 d mh excavator (prefix pel) service repair manual (pel000...fjjskekdmme
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble various components of the pump such as pistons, bearings, gears, covers, and valves. Tools required include lever pullers, link brackets, and retaining ring pliers. Photos illustrate each step, and torque specifications are provided for fasteners. The overall process installs the pump, connects hoses and wiring, and mounts related components back onto the excavator.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor, and tightening bolts. Safety precautions are mentioned such as releasing hydraulic pressure before disassembly and containing fluids properly. Required tools include lifting brackets, bolts, washers, and vacuum caps.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly procedure involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly procedure describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 330 d mh excavator (prefix pel) service repair manual (pel000...fjjskekdmme
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble various components of the pump such as pistons, bearings, gears, covers, and valves. Tools required include lever pullers, link brackets, and retaining ring pliers. Photos illustrate each step, and torque specifications are provided for fasteners. The overall process installs the pump, connects hoses and wiring, and mounts related components back onto the excavator.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor, and tightening bolts. Safety precautions are mentioned such as releasing hydraulic pressure before disassembly and containing fluids properly. Required tools include lifting brackets, bolts, washers, and vacuum caps.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly procedure involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly procedure describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR LJY
Configuration: 336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3 Engines for Caterpillar Built Machines
Media Number -UENR0130-06 Publication Date -01/08/2015 Date Updated -22/05/2017
i06601367
Diesel Exhaust Fluid Module - Disassemble
SMCS - 108H-015; 108K
Disassembly Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain diesel exhaust fluid into a suitable container for storage or disposal.
1/9
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g03365452
Note: Refer to Special Instruction, REHS8231, "Removal Procedures for Diesel Exhaust
Fluid (DEF) Connectors" for the correct removal procedure of hose assemblies (4).
2. Remove clips (1) and (5). Disconnect harness assemblies (2). Remove hose assemblies (4)
and hoses (3).
Illustration 2 g03365463
3. Remove cable straps (6) and disconnect harness assembly (7).
Illustration 3 g03365465
2/9
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 19 g03366046
20. Remove bolts (41). Separate support assembly (42) from pump (43).
Illustration 20 g03366053
21. Remove cable straps (45) and harness assembly (44).
Illustration 21 g06003622
Note: Place identification marks on DEF pump coolant connectors (46) and DEF pump
connectors (47) for installation purposes. DEF pump coolant connectors (46) and DEF
pump connectors (47) are not interchangeable.
8/9
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 22. Remove DEF pump coolant connectors (46) and DEF pump connectors (47) . Remove the
O-ring seals.
Illustration 22 g06040542
23. Remove bracket (48). Remove hose assembly (49).
Illustration 23 g06040545
24. Remove nuts (53). Remove straps (52). Remove tank (50) from support assembly (51).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 22:16:05 UTC+0800 2020
9/9
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR LJY
Configuration: 336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3 Engines for Caterpillar Built Machines
Media Number -UENR0130-06 Publication Date -01/08/2015 Date Updated -22/05/2017
i06846104
Diesel Exhaust Fluid Module - Assemble
SMCS - 108H-016; 108K
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Distilled Water
-
De-ionized Water
Diesel Exhaust Fluid (DEF)
Illustration 1 g06003622
Note: DEF pump coolant connectors (46) and DEF pump connectors (47) must be installed
in the original location when removed. DEF pump coolant connectors (46) and DEF pump
connectors (47) are not interchangeable.
1/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 1. Install the O-ring seals (not shown) .Install DEF pump coolant connectors (46) and DEF
pump connectors (47).
2. Tighten DEF pump coolant connectors (46) to a torque of 5.5 ± 0.5 N·m (48 ± 4 lb in).
3. Tighten DEF pump connectors (47) to a torque of 4.5 ± 0.5 N·m (40 ± 4 lb in).
Illustration 2 g03366053
4. Install harness assembly (44) and cable straps (45).
Illustration 3 g03366046
Note: Do not use an impact on bolts (41).
5. Install pump (43) in support assembly (42)
6. . Install bolts (41). Tighten bolts (41) to a torque of 19 ± 2 N·m (168 ± 18 lb in).
2/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 4 g03366035
7. Connect harness assembly (40).
Illustration 5 g03366015
Note: Do not use an impact on bolts (39).
8. Install bracket (37), bolts (39), and cable straps (38).
Illustration 6 g03383610
9. Install filter (36).
3/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 7 g03383609
10. Install expansion device (35).
Illustration 8 g03383608
11. Install cover (34). Tighten cover (34) to a torque of 20 ± 5 N·m (177 ± 44 lb in).
Illustration 9 g03365554
12. Install electronic control (31).
13. Install cable straps (32) and connect harness assembly (33).
4/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 10 g03365547
14. Install control module (30) and bolts (29). Tighten bolts (29) to a torque of 10 ± 2 N·m
(89 ± 18 lb in).
Illustration 11 g03365540
Note: Do not use an impact on the bolts for relays (28).
15. Install relays (28).
Illustration 12 g03365528
Note: Do not use an impact on the bolts for solenoid assembly (27).
5/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 16. Install solenoid assembly (27) and connect harness assembly (26).
Illustration 13 g03365521
17. Install plug (24) and plug (25) on manifold (22).
18. Install O-ring seals (23) in cap (21).
Illustration 14 g03365514
Note: Do not use an impact on bolts (19).
19. Install manifold (20), bolts (19), cap (17), bolts (18). Tighten bolts (18) to a torque of
6 ± 1 N·m (53 ± 9 lb in)
6/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 15 g03365493
20. Install bracket (16) on the tank.
21. Install bolts (15).
Illustration 16 g03365477
22. Install pump assembly (14) and bolts (13).
Illustration 17 g03365475
Note: Do not use an impact on bolt (12).
23. Install bolt (12). Tighten bolt (12) to a torque of 4 ± 1 N·m (35 ± 9 lb in)
7/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 18 g03365468
24. Install bolts (11).
Illustration 19 g03365465
25. Install the gasket (not shown), manifold (10), plate (9), and bolts (8). Tighten bolts (8) in an
alternating sequence to a torque of 5 ± 1 N·m (44 ± 9 lb in). Tighten bolts (8) a second time
in an alternating sequence to a torque of 5 ± 1 N·m (44 ± 9 lb in).
Illustration 20 g03365463
26. Connect harness assembly (7) and install cable straps (6).
8/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 21 g03365452
Note: Do not use an impact on the bolts for clips (1) and (5).
27. Install hoses (3). Apply Tooling (A) to the O-rings (not shown) inside hose assemblies (4).
Connect hose assemblies (4) and harness assemblies (2). Install clips (1). Tighten the bolts
for clips (1) to a torque of 6 ± 1 N·m (53 ± 9 lb in). Install clips (5).
Illustration 22 g06040545
9/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 23 g03376333
28. Install tank (50) in support assembly (51).
29. Install straps (52) and nuts (53). Tighten nuts (53) to a torque of 8 ± 2 N·m (71 ± 18 lb in).
Torque nuts (53) to a final torque of 11 ± 1 N·m (97 ± 9 lb in).
Note: Only apply torque once to nuts (53) when tightening straps (52). Apply torque to nuts
(53) in the W, X, Y, Z sequence shown in Illustration 23.
Note: Two types of straps are used to support different tank configurations. Only apply
torque once to the nuts on both types of straps.
Illustration 24 g06040542
30. Install bracket (48) and hose assembly (49).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 22:17:01 UTC+0800 2020
10/10
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR LJY
Configuration: 336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3 Engines for Caterpillar Built Machines
Media Number -UENR0130-06 Publication Date -01/08/2015 Date Updated -22/05/2017
i05891021
Diesel Exhaust Fluid Filter - Remove and Install
SMCS - 108K-010-FI
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 443-0955 DEF Filter Removal Tool 1
Personal injury can result from improper handling of chemicals.
Make sure you use all the necessary protective equipment required to
do the job.
Make sure that you read and understand all directions and hazards
described on the labels and material safety data sheet of any chemical
that is used.
Observe all safety precautions recommended by the chemical
manufacturer for handling, storage, and disposal of chemicals.
NOTICE
1/4
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03373816
1. Remove cover (1) .
Illustration 2 g03373819
2/4
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 3 g03373821
Illustration 4 g03709361
For Reference
2. Remove expansion device (2) .
3. Use Tooling (A) to remove diesel exhaust fluid filter (3) .
Note: Avoid twisting the diesel exhaust fluid filter upon removal. Twisting may cause a
tear.
Installation Procedure
1. Install diesel exhaust fluid filter (3) in the reverse order of removal.
Note: Avoid twisting the diesel exhaust fluid filter upon installation. Twisting may cause a
tear.
3/4
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. a. Lubricate seals of diesel exhaust fluid filter (3) with diesel exhaust fluid or distilled
water.
b. Tighten cover (1) to a torque of 20 ± 5 N·m (177 ± 44 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 22:17:57 UTC+0800 2020
4/4
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR LJY
Configuration: 336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3 Engines for Caterpillar Built Machines
Media Number -UENR0130-06 Publication Date -01/08/2015 Date Updated -22/05/2017
i06846092
Diesel Exhaust Fluid Pump - Remove and Install
SMCS - 108J-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Distilled Water
-
De-ionized Water
Diesel Exhaust Fluid (DEF)
B 316-0704 Locking Pliers 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/5
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 1 g03384472
1. Clamp off hoses (1) and (2) with Tooling (B).
Illustration 2 g03382731
Note: Refer to Special Instruction, REHS8231, "Removal Procedures for Diesel Exhaust
Fluid (DEF) Connectors" for the correct removal procedure of hose assemblies (3).
2. Disconnect harness assemblies (6). Remove clips (5) and (7).
3. Remove hose assemblies (3) and hoses (4).
Illustration 3 g03382869
2/5
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 4. Remove cable straps (8) and position the harness assembly out of the way.
5. Remove bolts (10) , cap (9), bolts (12), and manifold assembly (11).
Illustration 4 g03382907
6. Remove O-ring seals (13) from cap (9).
Illustration 5 g03382878
7. Remove cable straps (15) and disconnect harness assemblies (14), (16), and (17). Position
harness assembly (18) out of the way.
Illustration 6 g03382883
3/5
336F L & 336F LN Excavators LJY00001-UP (MACHINE) POWERED BY C9.3 En...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...