The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section outlines 14 steps, including installing pistons, bearings, covers, and seals in the reverse order of disassembly. Tools required include retaining ring pliers, a slide hammer, and driver group. Personal safety precautions are noted for releasing spring forces.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 313D2 and 313D2 GC excavator models. It lists the required tools and gives step-by-step instructions to remove components like sprockets, fittings, valves, seals, springs, pistons, plates, and barrels. Safety notices are included to warn of hazards like stored energy in springs, hot or pressurized fluids, and heavy component weights.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 324 d ln excavator (prefix trh) service repair manual (trh000...jfksekmmdme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D L and 324D LN. It includes:
1) A list of required tools for disassembly and assembly.
2) Detailed step-by-step instructions for disassembling components of the travel motor such as removing the head, brake piston, plates and discs, bearings and seals.
3) Detailed step-by-step instructions for assembling the travel motor in reverse order, including applying thread lock compound and ensuring cleanliness.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 416 d backhoe loader (prefix bfp) service repair manual (bfp1...fujsjefjsekkem
The document provides instructions for disassembling and assembling the transmission of a 416D Backhoe Loader. It lists the required tools and gives step-by-step details on how to remove each transmission component and reassemble it. The transmission is disassembled into its major components, which are then further disassembled into individual parts like gears, shafts, seals and housings. Precautions are given to ensure cleanliness during disassembly and assembly.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 313D2 and 313D2 GC excavator models. It lists the required tools and gives step-by-step instructions to remove components like sprockets, fittings, valves, seals, springs, pistons, plates, and barrels. Safety notices are included to warn of hazards like stored energy in springs, hot or pressurized fluids, and heavy component weights.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 324 d ln excavator (prefix trh) service repair manual (trh000...jfksekmmdme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D L and 324D LN. It includes:
1) A list of required tools for disassembly and assembly.
2) Detailed step-by-step instructions for disassembling components of the travel motor such as removing the head, brake piston, plates and discs, bearings and seals.
3) Detailed step-by-step instructions for assembling the travel motor in reverse order, including applying thread lock compound and ensuring cleanliness.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 416 d backhoe loader (prefix bfp) service repair manual (bfp1...fujsjefjsekkem
The document provides instructions for disassembling and assembling the transmission of a 416D Backhoe Loader. It lists the required tools and gives step-by-step details on how to remove each transmission component and reassemble it. The transmission is disassembled into its major components, which are then further disassembled into individual parts like gears, shafts, seals and housings. Precautions are given to ensure cleanliness during disassembly and assembly.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Required tools are listed in a table at the beginning.
Caterpillar cat 305.5 e mini hydraulic excavator (prefix ygb) service repair ...fisjejfskemmd
The document provides instructions for disassembling the final drive and travel motor of a 305.5E Mini Hydraulic Excavator. It lists 38 steps to remove parts like gears, bearings, springs, seals, and other components. Tools required include a crossblock, retaining ring pliers, bearing puller, and two spanner wrenches. Detailed illustrations accompany each step to show how to remove each part in the proper order. Safety warnings are included to remind technicians to wear protective equipment when releasing spring forces.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fjkskefksmeme
1) The document provides disassembly instructions for components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification numbers where applicable.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, seals and other parts while taking care to mark locations for reassembly.
Caterpillar cat 326 d2 l excavator (prefix mzh) service repair manual (mzh000...fjsekdmmeed
This document provides instructions for disassembling and assembling the travel motor of an excavator model 326D2 L. The disassembly procedure involves removing 27 different components of the travel motor including the head, port plate, springs, brake piston, plates, and seals. The assembly procedure instructs installing the components in reverse order and notes that all seals and gaskets must be replaced, parts must be thoroughly cleaned, and lubricant applied before assembly. Proper placement of marked components like pistons is emphasized.
This document provides disassembly instructions for a piston pump on a 252B3 skid steer loader. It lists 69 steps to fully disassemble the pump, removing components like fittings, springs, seals, bearings, shafts and housings. Measurements are taken of component distances during disassembly for reassembly purposes. Safety warnings are provided to wear protective equipment when removing parts with spring forces.
Caterpillar cat 312 d excavator (prefix jbc) service repair manual (jbc00001 ...fksjksmmde
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 312D or 312D L excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, valves, gears, plates, seals, and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Detailed illustrations supplement the text to show how to take each component apart.
Caterpillar cat 325 d excavator (prefix pke) service repair manual (pke00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1) Removing the final drive assembly and marking parts for reinstallation.
2) Disassembling components like gears, bearings, and seals.
3) Cleaning all parts thoroughly before assembly to prevent dirt from entering mechanisms.
4) Assembling components and pressing bearings into place, applying the proper preload using shims.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...zatao0179249295
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Pictures accompany each step to illustrate the parts and procedures.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...luanxianshi27
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Pictures and illustrations are provided to aid the process.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...cnp692569
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Precautions are included for releasing spring forces to avoid injury.
Caterpillar cat 390 f l excavator (prefix hjd) service repair manual (hjd0000...fujskekfmsme
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...jdjkskmikdkmd
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It instructs the technician to remove components like the motor head, relief valves, spools, pistons, plates, and seals. Tools required include link brackets, a slide hammer, threaded rods, pliers, and drivers. Safety notices warn of spring forces and contained fluids.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...paws21610697
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It instructs the technician to remove components like the motor head, relief valves, spools, pistons, plates, and seals. Tools required include link brackets, a slide hammer, threaded rods, pliers, and drivers. Safety notices warn of spring forces and contained fluids.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...uddksemd8ud
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to disassemble the various components of the travel motor, including removing the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required and care must be taken to avoid injury from parts under spring pressure.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...f7djidksmd3e
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, piston, springs, seals, port plate, separator plates, friction plates, barrel assembly, piston assemblies, retainer, guide, swashplate, and seals. Various tools are required to remove components and release spring pressure. Precautions are listed to contain fluids, mark components for reinstallation, and wear protective equipment when removing parts under spring force.
Caterpillar cat 390 f l excavator (prefix hjd) service repair manual (hjd0000...ifkkdmdmdm
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, piston, springs, seals, port plate, separator plates, friction plates, barrel assembly, piston assemblies, retainer, guide, swashplate, and seals. Various tools are required to remove components and release spring pressure. Precautions are listed to contain fluids, mark components for reinstallation, and protect from spring force.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...f8uuseijdkmd3e
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It instructs the technician to remove components like the motor head, relief valves, ports, pistons, plates, and seals. Precautions are given to watch for spring forces and contain fluids during disassembly. Tools needed include link brackets, pullers, rods, pliers, and drivers.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual Instant D...jiuliu14811471
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to disassemble the various components of the travel motor, including removing the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required and care must be taken to avoid injury from parts under spring pressure.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual Instant D...jiuliu14811471
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to disassemble the various components of the travel motor, including removing the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required and care must be taken to avoid injury from parts under spring pressure.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual Instant D...qianxu35543635
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to fully disassemble the travel motor and its components. Key steps include removing the motor head, relief valves, pistons, springs, seals, plates, bearings, and shaft. Precision tools and following the provided safety warnings are important for safe and proper disassembly of the travel motor.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...jdjkskmikdkmd
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, pistons, springs, seals, plates, barrel assembly, swashplate, shafts, bearings, and seals. Detailed illustrations accompany each step and special safety notices are included. Tools required include link brackets, slide hammers, threaded rods, pliers, drivers, and bolts.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...paws21610697
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
The document provides disassembly instructions for the final drive, travel motor, and other components of a 313D2 excavator. It lists over 30 detailed steps to disassemble parts like the final drive, counterbalance valve, travel motor, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like parts propelled by springs, hydraulic pressure, and heavy component weights. Required tools are listed in a table at the beginning.
Caterpillar cat 305.5 e mini hydraulic excavator (prefix ygb) service repair ...fisjejfskemmd
The document provides instructions for disassembling the final drive and travel motor of a 305.5E Mini Hydraulic Excavator. It lists 38 steps to remove parts like gears, bearings, springs, seals, and other components. Tools required include a crossblock, retaining ring pliers, bearing puller, and two spanner wrenches. Detailed illustrations accompany each step to show how to remove each part in the proper order. Safety warnings are included to remind technicians to wear protective equipment when releasing spring forces.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fjkskefksmeme
1) The document provides disassembly instructions for components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification numbers where applicable.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, seals and other parts while taking care to mark locations for reassembly.
Caterpillar cat 326 d2 l excavator (prefix mzh) service repair manual (mzh000...fjsekdmmeed
This document provides instructions for disassembling and assembling the travel motor of an excavator model 326D2 L. The disassembly procedure involves removing 27 different components of the travel motor including the head, port plate, springs, brake piston, plates, and seals. The assembly procedure instructs installing the components in reverse order and notes that all seals and gaskets must be replaced, parts must be thoroughly cleaned, and lubricant applied before assembly. Proper placement of marked components like pistons is emphasized.
This document provides disassembly instructions for a piston pump on a 252B3 skid steer loader. It lists 69 steps to fully disassemble the pump, removing components like fittings, springs, seals, bearings, shafts and housings. Measurements are taken of component distances during disassembly for reassembly purposes. Safety warnings are provided to wear protective equipment when removing parts with spring forces.
Caterpillar cat 312 d excavator (prefix jbc) service repair manual (jbc00001 ...fksjksmmde
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 312D or 312D L excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, valves, gears, plates, seals, and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized fluids. Detailed illustrations supplement the text to show how to take each component apart.
Caterpillar cat 325 d excavator (prefix pke) service repair manual (pke00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1) Removing the final drive assembly and marking parts for reinstallation.
2) Disassembling components like gears, bearings, and seals.
3) Cleaning all parts thoroughly before assembly to prevent dirt from entering mechanisms.
4) Assembling components and pressing bearings into place, applying the proper preload using shims.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...zatao0179249295
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Pictures accompany each step to illustrate the parts and procedures.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...luanxianshi27
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Pictures and illustrations are provided to aid the process.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...cnp692569
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Precautions are included for releasing spring forces to avoid injury.
Caterpillar cat 390 f l excavator (prefix hjd) service repair manual (hjd0000...fujskekfmsme
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...jdjkskmikdkmd
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It instructs the technician to remove components like the motor head, relief valves, spools, pistons, plates, and seals. Tools required include link brackets, a slide hammer, threaded rods, pliers, and drivers. Safety notices warn of spring forces and contained fluids.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...paws21610697
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It instructs the technician to remove components like the motor head, relief valves, spools, pistons, plates, and seals. Tools required include link brackets, a slide hammer, threaded rods, pliers, and drivers. Safety notices warn of spring forces and contained fluids.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...uddksemd8ud
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to disassemble the various components of the travel motor, including removing the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required and care must be taken to avoid injury from parts under spring pressure.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...f7djidksmd3e
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, piston, springs, seals, port plate, separator plates, friction plates, barrel assembly, piston assemblies, retainer, guide, swashplate, and seals. Various tools are required to remove components and release spring pressure. Precautions are listed to contain fluids, mark components for reinstallation, and wear protective equipment when removing parts under spring force.
Caterpillar cat 390 f l excavator (prefix hjd) service repair manual (hjd0000...ifkkdmdmdm
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, piston, springs, seals, port plate, separator plates, friction plates, barrel assembly, piston assemblies, retainer, guide, swashplate, and seals. Various tools are required to remove components and release spring pressure. Precautions are listed to contain fluids, mark components for reinstallation, and protect from spring force.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual (HJD00001...f8uuseijdkmd3e
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It instructs the technician to remove components like the motor head, relief valves, ports, pistons, plates, and seals. Precautions are given to watch for spring forces and contain fluids during disassembly. Tools needed include link brackets, pullers, rods, pliers, and drivers.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual Instant D...jiuliu14811471
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to disassemble the various components of the travel motor, including removing the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required and care must be taken to avoid injury from parts under spring pressure.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual Instant D...jiuliu14811471
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to disassemble the various components of the travel motor, including removing the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required and care must be taken to avoid injury from parts under spring pressure.
Caterpillar Cat 390F L Excavator (Prefix HJD) Service Repair Manual Instant D...qianxu35543635
The document provides disassembly instructions for a travel motor on a 390F L excavator. It involves 40 steps to fully disassemble the travel motor and its components. Key steps include removing the motor head, relief valves, pistons, springs, seals, plates, bearings, and shaft. Precision tools and following the provided safety warnings are important for safe and proper disassembly of the travel motor.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...jdjkskmikdkmd
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, pistons, springs, seals, plates, barrel assembly, swashplate, shafts, bearings, and seals. Detailed illustrations accompany each step and special safety notices are included. Tools required include link brackets, slide hammers, threaded rods, pliers, drivers, and bolts.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...paws21610697
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...uddksemd8ud
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, pistons, springs, seals, plates, barrel assembly, swashplate, shafts, bearings, and seals. Various tools are required to carefully remove each component while maintaining proper alignment and ordering of parts for reassembly. Safety notices are included to contain fluids, handle pressurized parts carefully, and wear protective equipment.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...f7djidksmd3e
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, pistons, springs, seals, plates, barrel assembly, swashplate, shafts, bearings, and seals. Detailed illustrations accompany each step and special safety notices are included. Tools required include link brackets, slide hammers, threaded rods, pliers, drivers, and bolts.
Caterpillar cat 390 f l excavator (prefix gay) service repair manual (gay0000...ifkkdmdmdm
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to fully disassemble the travel motor including removing the head, relief valves, pistons, springs, seals, plates, barrel assembly, swashplate, shafts, bearings, and seals. Detailed illustrations accompany each step and special safety notices are included. Tools required include link brackets, slide hammers, threaded rods, pliers, drivers, and bolts.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual (GAY00001...f8uuseijdkmd3e
This document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and drivers. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar Cat 390F L Excavator (Prefix GAY) Service Repair Manual Instant D...jiuliu14811471
This document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Similar to Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct00001 and up) (20)
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 80 l tractor service repair...fjekkdmmem
This document provides part numbers and descriptions for engine components of a McCormick RT30 tractor. It lists 46 individual parts for the engine, including cylinders, pistons, gears, shafts, plates and other internal components. Each part is identified by a reference number, description, and whether it is for the engine (T-A) or transmission (T-B). It also specifies components that are part of assemblies and not individually serviced.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 75 l tractor service repair...fjekkdmmem
This document provides component part listings and information for an engine. It includes over 80 individual part listings with details like part numbers, replacement kits, and torque specifications. The parts are for components of the engine like the cylinder block, crankshaft, pistons, rods, head, valves, rockers, and various fasteners. It also provides the engine model and serial number range the parts correspond to.
Mc cormick c l mondial tier 2 (2007- ) - rt30 - c 60 l tractor service repair...fjekkdmmem
This document contains information about engine components for a Perkins engine, including identification numbers, part names and numbers, quantities, and repair kit information. It lists 40 line items describing individual engine parts and components such as cylinders, bearings, gears, plates, seals, and other items, along with specifications like torque settings. Additional information provided includes manufacturer and model details and notes on replacement parts.
Mc cormick c l europa tier 3 (2008-2015) - rs51 - c80l tractor service repair...fjekkdmmem
This document provides component part listings and information for engines. It includes listings of parts with identification numbers, part names, quantities and other technical specifications. For example, it lists a Perkins engine with a 54.5 kw output, and it provides listings of cylinder blocks, gears, pistons and other engine parts along with identifying information for each. It contains detailed technical specifications and part numbers for replacement components.
Mc cormick c l europa tier 3 (2008-2015) - rs51 - c75l tractor service repair...fjekkdmmem
This document provides component part listings and information for the repair and replacement of parts for a Perkins XL75075 engine. It includes over 40 individual part listings with details like part numbers, component names, replacement part kits, and specifications. The parts cover various engine systems like the cylinder block, crankshaft, cylinder head, camshaft, and fuel system.
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 80 tractor service repair m...fjekkdmmem
This document provides a list of components for an engine, including identification numbers, names, and other details. It lists items like cylinders, bearings, plugs, gears, plates, and other engine parts. Quantities and part numbers are provided for each component. Notes indicate some items are only to be ordered as replacements and provide color coding for identifying similar parts.
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 60 tractor service repair m...fjekkdmmem
This document contains parts lists and component information for engines. It lists individual engine parts like cylinders, bearings, plugs, and includes information like part numbers, replacement kits, and quantity per tractor. The parts are associated with assemblies for engines and components like the head, shaft, rockers, and gear kit. Quantity, replacement and reference information is provided for each listed part.
Mc cormick c series c100 tractor service repair manualfjekkdmmem
The document contains parts listings and diagrams for engine, cooling system, air intake, and exhaust components for McCormick tractors. It includes lists of parts with identification numbers, quantities, and component names. Diagrams show the assembly and placement of parts within various engine and systems. The document provides extensive reference information for locating and identifying replacement parts for several tractor systems.
Mc cormick c series c90 tractor service repair manualfjekkdmmem
The document contains parts listings and diagrams for engine, cooling system, air intake, and exhaust components for McCormick tractors. It includes lists of parts with descriptions and part numbers needed to service or replace components like the engine, radiator, air cleaner, and exhaust system. Diagrams show the assembly, placement and connections of parts in the various systems. The document provides the information necessary to identify replacement parts for maintenance and repair of engine-related systems.
Mc cormick c series c80 tractor service repair manualfjekkdmmem
The document contains parts listings and diagrams for engine, cooling system, air intake, and exhaust components for McCormick tractors. It includes lists of parts with descriptions and part numbers needed to service or replace components like the engine, radiator, air cleaner, and exhaust system. Diagrams show the assembly, placement and connections of parts in the various systems. The document provides the information necessary to identify replacement parts for maintenance and repair of engine-related systems.
Kubota b1700 d tractor parts catalogue manualfjekkdmmem
The document provides instructions and definitions for parts books. It defines column headings for part number pages including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It notes country codes that may be included and what they represent. The document then provides an index of parts for Reference B1700D organized by system, with the corresponding part number, description, and parts book reference.
Kubota b1550 hst d tractor parts catalogue manualfjekkdmmem
The document provides instructions and part listings for a parts book. It defines the column headings used in parts book pages including part number, description, quantity, and serial number range. Country codes are also defined, indicating any country-specific differences. The remainder of the document is a sample page from the parts book, listing over 100 individual part numbers for a tractor engine and components.
Kubota b1550 e tractor parts catalogue manualfjekkdmmem
The document provides instructions for parts books. It defines column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for. An example page from a parts book is then shown, listing parts for a B1550E engine with corresponding details.
Cub cadet lt 1222 lawn tractor service repair manualfjekkdmmem
This service manual provides instructions for servicing 1000/1500 series riding tractors manufactured by MTD Products Inc. It covers a range of models from 2001-2006 with various engines and drive systems. The manual outlines procedures for removing and replacing components like the hood, fenders, deck, drive belts, brakes, and transaxle. Safety notices advise that the manual is intended for trained technicians experienced with outdoor power equipment.
Cub cadet lt 1050 lawn tractor service repair manualfjekkdmmem
This service manual provides instructions for servicing 1000/1500 Series riding tractors manufactured by MTD Products Inc. It covers a range of models from 2001-2006 with various single-cylinder and V-twin engines from Kohler and Kawasaki. The manual describes the different hood, deck, and drive system configurations used on these tractors and provides procedures for removing components like the hood, fenders, deck, and transaxle for repair. Safety notices advise that the manual is intended only for trained technicians experienced with outdoor power equipment.
Claas dominator 98 combine (093) service repair manualfjekkdmmem
The document is a repair manual that provides instructions for repairing various components of CLAAS Dominator 108 VX, 98 VX, and 88 VX combine harvesters. It includes sections on the operator's platform, threshing mechanism, cleaning systems, and other areas. The manual provides detailed steps for removing, dismantling, installing, and assembling parts. It also includes exploded diagrams and specifications to aid in repairs.
Claas dominator 88 combine (092) service repair manualfjekkdmmem
The document is a repair manual that provides instructions for repairing various components of CLAAS Dominator 108 VX, 98 VX, and 88 VX combine harvesters. It includes sections on the operator's platform, threshing mechanism, cleaning systems, and other areas. The manual provides detailed steps for removing, dismantling, installing, and assembling parts. It also includes exploded diagrams and specifications to aid in repairs.
New holland t7.220 power command tractor service repair manualfjekkdmmem
This document is a service manual for Case IH T7 tractor models 220, 235, 250, 260, and 270. It provides specifications and repair/maintenance procedures for the engine, transmission, axles, brakes, hydraulics, pneumatics, hitches, frames, steering, wheels, climate control, and electrical systems of these tractor models. The manual is intended to assist technicians in servicing and repairing components of the tractors. It contains detailed sections on the engine, transmission, axles and other core systems along with part numbers and specifications.
New holland t7.175 auto command stage iv tractor service repair manualfjekkdmmem
This document is a service manual that provides information on servicing various components of tractor models T7.175 AutoCommandTM, T7.175, T7.190 AutoCommandTM, T7.190, T7.210 AutoCommandTM, T7.210, and T7.225 AutoCommandTM. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes, hydraulic systems, pneumatic system, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork and decals. Each section provides removal and installation instructions, specifications
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ZCT
Configuration: 336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03898826
Main Hydraulic Pump - Disassemble
SMCS - 5070-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
156-7100 Slide Hammer Puller Gp 1
4C-5656 Adapter 1
B 138-7574 Link Bracket 2
C 1P-1855 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E 5P-5197 Retaining Ring Pliers As 1
F 5P-4758 Retaining Ring Pliers As 1
Start By:
A. Remove the main hydraulic pump. Refer to Disassembly and Assembly, "Main Hydraulic
Pump - Remove".
B. Remove the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Pilot) -
Remove".
1/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01212500
1. Remove bolts (1) , sensor (2) , the O-ring seal, and the backup ring.
Illustration 2 g01212501
2. Remove bolts (3) , sensor (4) , the O-ring seal, and the backup ring.
Illustration 3 g01212677
3. Remove bolts (5) and housing (6) .
2/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g01212502
4. Remove O-ring seals (7) .
Illustration 5 g01212503
5. Remove bolts (9) , solenoid (8) , and the O-ring seals.
3/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 6 g01212506
6. Remove bolts (10) and valve (11) .
Illustration 7 g01212507
7. Remove O-ring seals (12) .
Illustration 8 g01212508
8. Remove bolts (13) , cover (14) , and the O-ring seals.
4/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 9 g01174684
9. Remove bolts (15) and cover (16) .
Illustration 10 g01174685
10. Use Tooling (A) in order to remove plug (18) and plug (17) .
Illustration 11 g01174686
5/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 12 g01174687
Illustration 13 g01174688
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
11. Remove bolts (19) , cover (20) , and the O-ring seals.
12. Remove bolts (21) , cover (22) , and the O-ring seals.
13. Remove spring (23) , spring (24) , and retainer (25) .
14. Remove spring (26) , sleeve (27) , and piston (28) .
6/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 14 g01174691
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (29) .
Illustration 15 g01174692
16. Remove spring (30) .
7/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 16 g01174693
Illustration 17 g01174694
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
17. Use Tooling (C) in order to remove retaining ring (40) .
18. Remove O-ring seals (34) .
19. Remove retainer (39) and spring (38) .
20. Remove lever (31) , lever (32) , and lever (33) .
21. Remove spool (35) , spool (37) , sleeve (36) , and spool (41) .
8/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 18 g01174695
22. Repeat Steps 6 through Steps 21 for valve (42) .
Illustration 19 g01174696
23. Attach Tooling (B) and a suitable lifting device to head assembly (45) .
24. Remove bolts (44) and bolts (43) .
25. Remove head assembly (45) .
9/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 20 g01174697
26. Remove port plates (47) and barrels (48) .
27. Remove gasket (46) .
Illustration 21 g01175099
28. Remove springs (49) .
Illustration 22 g01174698
10/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 29. Remove bearings (52) , pistons (50) , and retainer (51) .
Illustration 23 g01174699
30. Remove plates (53) and swashplates (54) .
Illustration 24 g02142325
31. Use Tooling (D) in order to remove retaining ring (82) . Remove seal (81) . Remove the O-
ring seal. Attach Tooling (B) and a suitable lifting device to cover (56) .
32. Remove bolts (55) and cover (56) .
11/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 25 g01174702
33. Use Tooling (D) in order to remove retaining ring (59) .
34. Remove shim (60) and gear (57) .
35. Use Tooling (E) in order to remove retaining ring (58) .
36. Remove shim (62) , gear (57A) , and the gasket (61) .
Illustration 26 g01174723
12/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 27 g01174724
37. Remove shim (66) .
38. Use Tooling (F) in order to remove retaining ring (63) .
39. Use Tooling (F) in order to remove retaining ring (65) .
40. Remove shaft assembly (64) .
41. Remove shaft assembly (67) .
42. Remove bolts (68) and bearing carriers (69) .
Illustration 28 g01174725
43. Use Tooling (D) in order to remove retaining ring (70) from bearing (72) .
44. Use Tooling (D) in order to remove retaining ring (71) .
Illustration 29 g01174813
45. Use a suitable press in order to remove bearing (72) from shaft assembly (67) .
13/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 30 g01174814
46. Use Tooling (D) in order to remove retaining ring (73) from bearing (74) .
Illustration 31 g01174815
47. Use a suitable press in order to remove bearing (74) from shaft assembly (64) .
14/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 32 g01174816
Note: Record the distance between nuts (77) and screws (76) for assembly purposes.
48. Remove nuts (77) and screws (76) .
49. Remove bolts (75) and covers (78) .
Illustration 33 g01174817
50. Remove plugs (79) and the O-ring seals.
Illustration 34 g01174818
51. Remove pistons (80) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 07:31:02 UTC+0800 2020
15/15336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ZCT
Configuration: 336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i04041156
Main Hydraulic Pump - Assemble
SMCS - 5070-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 138-7574 Link Bracket 2
C 1P-1855 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E 5P-5197 Retaining Ring Pliers As 1
F 5P-4758 Retaining Ring Pliers As 1
G 1P-0520 Driver Gp 1
H 1P-1861 Retaining Ring Pliers 1
J - M6x2x50mm Guide Pin 2
1/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 1 g02251815
1. Install pin assemblies (81).
Illustration 2 g02251817
2. Install pistons (80) into pin assemblies (81).
2/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 3 g01174817
3. Install plugs (79) and the O-ring seals.
Illustration 4 g01174816
4. Install covers (78) and bolts (75).
5. Tighten nuts (77) and screws (76).
Illustration 5 g01174814
6. Raise the temperature of bearing (74).
7. Install bearing (74).
3/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 8. Use Tooling (D) in order to install retaining ring (73).
Illustration 6 g01174725
9. Raise the temperature of bearing (72).
10. Install bearing (72).
11. Use Tooling (D) in order to install retaining ring (70).
12. Use Tooling (D) in order to install retaining ring (71).
Illustration 7 g01174723
4/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 8 g01174724
13. Install bearing carriers (69) and bolts (68).
14. Install shaft assembly (67).
15. Install shaft assembly (64).
16. Use Tooling (F) in order to install retaining ring (65).
17. Use Tooling (F) in order to install retaining ring (63).
18. Install shim (66).
Illustration 9 g01174702
19. Install gasket (61), gear (57A), and shim (62).
20. Use Tooling (E) in order to install retaining ring (58).
21. Install gear (57A) and shim (60).
22. Use Tooling (D) in order to install retaining ring (59).
Illustration 10 g02264075
5/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 11 g02263333
23. Install the O-ring seal into cover (56). Use Tooling (G) to install seal (82). Use Tooling (H)
in order to install the retaining ring (83).
Note: In order to install seal (82) with the main hydraulic pump assembled, Refer to Service
Magazine, SEPD0930, "New Seals in the Main Hydraulic Pump Prevent Oil Leaks from the
Pump Shaft".
24. Attach Tooling (B) and a suitable lifting device to cover (56).
25. Install a lubricated protective sleeve over the shaft in order to protect the seal during
installation of the cover. Install cover (56) and bolts (55).
Illustration 12 g01174699
26. Install swashplates (54) and plates (53).
6/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 16 g01175041
Illustration 17 g02257096
30. Use a suitable string in order to retain the pistons during installation.
31. Install barrels (48).
Illustration 18 g02257113
32. Install port plates (47) onto head assembly (45).
33. Install gasket (46).
8/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 19 g01174696
34. Use Tooling (B) and a suitable lifting device in order to install head assembly (45).
35. Install bolts (44) and bolts (43).
Illustration 20 g01174693
Illustration 21 g01174694
36. Install spool (35), spool (37), sleeve (36), and spool (41).
37. Install lever (33), lever (32), and lever (31).
38. Install spring (38) and retainer (39).
9/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP65...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. 39. Use Tooling (C) in order to install retaining ring (40).
40. Install O-ring seals (34).
Illustration 22 g01174692
41. Install spring (30).
Illustration 23 g01174691
42. Install plug (29).
Illustration 24 g01174686
10/16336D2 L Excavator ZCT00001-UP (MACHINE) POWERED BY C9 Engine(SEBP...
2020/6/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...