This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...cdsasw
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations are provided to identify each component mentioned in the instructions. Safety notices are included to warn of potential hazards like parts propelled by springs.
This document provides instructions for disassembling a travel motor. It lists 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group and more. Safety precautions are provided to be careful of spring forces and contain fluids. The detailed procedures involve attaching the motor vertically, marking parts, applying air pressure, using presses and pullers, and removing retaining rings.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...cdsasw
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations are provided to identify each component mentioned in the instructions. Safety notices are included to warn of potential hazards like parts propelled by springs.
This document provides instructions for disassembling a travel motor. It lists 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group and more. Safety precautions are provided to be careful of spring forces and contain fluids. The detailed procedures involve attaching the motor vertically, marking parts, applying air pressure, using presses and pullers, and removing retaining rings.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c l excavator (prefix mdy) service repair manual (mdy0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then lists 7 notes and 28 steps to reassemble the final drive, installing components like seals, bearings, shims, and alignment pins in the reverse order of disassembly.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c l excavator (prefix mdy) service repair manual (mdy0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then lists 7 notes and 28 steps to reassemble the final drive, installing components like seals, bearings, shims, and alignment pins in the reverse order of disassembly.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR FAJ
Configuration: 336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i06605028
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 x 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 88 kg (195 lb).
1/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the heads original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
Example of the use of Tooling (B).
3/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (D) to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press to remove bearing race (18) from shaft (15).
Illustration 13 g03870797
16. Rotate shaft (15). Use a suitable press and Tooling (E) to remove bearing race (19) from
shaft (15).
Illustration 14 g03870686
17. Remove cam plate (20) from barrel assembly (16).
6/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g03870754
18. Remove piston assemblies and retainer plate (21) from barrel assembly (16).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g03870760
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (22) and springs (23).
7/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g03870766
20. Remove bearing (24).
21. Remove keys (25) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g03870770
22. Rotate the housing. Use Tooling (F) to remove retaining ring (26).
23. Remove lip seal (27).
Illustration 19 g03870778
24. Remove bolts (28) and cover (29).
8/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g03870779
25. Remove seal (30) and backup ring (31).
Illustration 21 g03870780
26. Remove piston actuator (32) and seal (33).
Illustration 22 g03870784
27. Remove O-ring seal (34) from the housing of the travel motor.
9/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR FAJ
Configuration: 336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR FAJ
Configuration: 336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i06242093
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 243 -
1/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g03870784
1. Install O-ring seal (34) onto the housing of the travel motor.
Illustration 2 g03870780
2. Install seal (33) and piston actuator (32). Lubricate the surfaces of piston actuator (32) with
lubricant that is being sealed.
Illustration 3 g03870779
3. Install backup ring (31) and seal (30).
2/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 4 g03870778
4. Install cover (29) and bolts (28). Tighten bolts (28) to a torque of 28 ± 7 N·m
(248 ± 62 lb in).
Illustration 5 g03870770
5. Apply Tooling (G) to the mating surface of lip seal (27). Use Tooling (E) in order to install
lip seal (27). Lubricate the sealing lip of lip seal (27) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (26).
Illustration 6 g03870766
3/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...