This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 324 d l excavator (prefix jzr) service repair manual (jzr0000...fjskekdmmem
This document provides the disassembly and assembly procedures for a 324D and 324D L excavator travel motor. The disassembly procedure involves 28 steps to remove components from the travel motor housing. The assembly procedure reverses the disassembly steps and involves installing components back into the housing, with notes to clean parts thoroughly, apply lubricant, and ensure proper positioning of parts. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d2 l excavator (prefix gja) service repair manual (gja000...fjjskekdm
1) The document provides step-by-step instructions for disassembling the travel motor on a 336D2L excavator. It details removing 27 individual components through a series of illustrated steps.
2) Special tools are listed that are required, including various bolts, pins, and bearing pullers. Safety precautions are provided to release spring forces.
3) Each step clearly pictures the component and identifies it by name or number, describing how to remove it from the travel motor assembly. Marks should be made to ensure correct reassembly.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 324 d l excavator (prefix jzr) service repair manual (jzr0000...fjskekdmmem
This document provides the disassembly and assembly procedures for a 324D and 324D L excavator travel motor. The disassembly procedure involves 28 steps to remove components from the travel motor housing. The assembly procedure reverses the disassembly steps and involves installing components back into the housing, with notes to clean parts thoroughly, apply lubricant, and ensure proper positioning of parts. Tools required for disassembly and assembly are also listed.
Caterpillar cat 336 d2 l excavator (prefix gja) service repair manual (gja000...fjjskekdm
1) The document provides step-by-step instructions for disassembling the travel motor on a 336D2L excavator. It details removing 27 individual components through a series of illustrated steps.
2) Special tools are listed that are required, including various bolts, pins, and bearing pullers. Safety precautions are provided to release spring forces.
3) Each step clearly pictures the component and identifies it by name or number, describing how to remove it from the travel motor assembly. Marks should be made to ensure correct reassembly.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c l excavator (prefix mdy) service repair manual (mdy0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then lists 7 notes and 28 steps to reassemble the final drive, installing components like seals, bearings, shims, and alignment pins in the reverse order of disassembly.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Caterpillar cat 318 c ln excavator (prefix gpa) service repair manual (gpa000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 318 c l excavator (prefix mdy) service repair manual (mdy0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then lists 7 notes and 28 steps to reassemble the final drive, installing components like seals, bearings, shims, and alignment pins in the reverse order of disassembly.
Caterpillar cat 318 c l excavator (prefix gpa) service repair manual (gpa0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and outlines 33 steps to disassemble parts like the carrier assembly, ring gears, and housing. It also outlines 14 steps for assembly, including installing bearings, seals, shims, and aligning the main and motor housings. Cleanliness is emphasized throughout to prevent damage during reassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR HBK
Configuration: 336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i06605028
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 x 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 88 kg (195 lb).
1/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the heads original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
Example of the use of Tooling (B).
3/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (D) to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press to remove bearing race (18) from shaft (15).
Illustration 13 g03870797
16. Rotate shaft (15). Use a suitable press and Tooling (E) to remove bearing race (19) from
shaft (15).
Illustration 14 g03870686
17. Remove cam plate (20) from barrel assembly (16).
6/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g03870754
18. Remove piston assemblies and retainer plate (21) from barrel assembly (16).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g03870760
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (22) and springs (23).
7/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g03870766
20. Remove bearing (24).
21. Remove keys (25) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g03870770
22. Rotate the housing. Use Tooling (F) to remove retaining ring (26).
23. Remove lip seal (27).
Illustration 19 g03870778
24. Remove bolts (28) and cover (29).
8/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g03870779
25. Remove seal (30) and backup ring (31).
Illustration 21 g03870780
26. Remove piston actuator (32) and seal (33).
Illustration 22 g03870784
27. Remove O-ring seal (34) from the housing of the travel motor.
9/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR HBK
Configuration: 336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERE...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERE...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERE...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERE...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR HBK
Configuration: 336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i06242093
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 243 -
1/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g03870784
1. Install O-ring seal (34) onto the housing of the travel motor.
Illustration 2 g03870780
2. Install seal (33) and piston actuator (32). Lubricate the surfaces of piston actuator (32) with
lubricant that is being sealed.
Illustration 3 g03870779
3. Install backup ring (31) and seal (30).
2/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 4 g03870778
4. Install cover (29) and bolts (28). Tighten bolts (28) to a torque of 28 ± 7 N·m
(248 ± 62 lb in).
Illustration 5 g03870770
5. Apply Tooling (G) to the mating surface of lip seal (27). Use Tooling (E) in order to install
lip seal (27). Lubricate the sealing lip of lip seal (27) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (26).
Illustration 6 g03870766
3/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 7. Rotate the housing.
8. Install keys (25) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (24).
Illustration 7 g03870760
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (23) into the barrel assembly. Install ball (22) onto springs (23). Lubricate
ball (22) with lubricant that is being sealed.
Illustration 8 g03870754
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (21) into barrel assembly (16).
4/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g03870686
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (16).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336D2, 336D2 L & 336D2 GC Excavators HBK00001-UP (MACHINE) POWERED ...
2020/5/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...