This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pullers, pry bars, and seal removal tools.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...cdsasw
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations are provided to identify each component mentioned in the instructions. Safety notices are included to warn of potential hazards like parts propelled by springs.
This document provides instructions for disassembling a travel motor. It lists 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group and more. Safety precautions are provided to be careful of spring forces and contain fluids. The detailed procedures involve attaching the motor vertically, marking parts, applying air pressure, using presses and pullers, and removing retaining rings.
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...cdsasw
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations are provided to identify each component mentioned in the instructions. Safety notices are included to warn of potential hazards like parts propelled by springs.
This document provides instructions for disassembling a travel motor. It lists 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group and more. Safety precautions are provided to be careful of spring forces and contain fluids. The detailed procedures involve attaching the motor vertically, marking parts, applying air pressure, using presses and pullers, and removing retaining rings.
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper order. It also provides disassembly instructions for a final drive in 13 steps, removing components like bolts, gears, and covers. Installation requires cleaning, applying sealant, and torquing bolts to specified values.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It describes 27 steps to disassemble the motor by removing components like the motor head, springs, brake piston, rotating assembly, bearings and seals. It then describes 28 steps for reassembling the motor components in reverse order, making sure to align parts properly, apply lubricants to seals and mating surfaces, and torque bolts to the specified values. The proper procedure is important to safely release spring forces and prevent damage during removal and installation of parts.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring forces or pressurized components.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...fhsjekdmme
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix fbt) service repair manual (fbt000...fhsjekdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar cat 336 d2 l excavator (prefix faj) service repair manual (faj000...fhsjekdmme
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pullers, pry bars, and seal removal tools.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper order. It also provides disassembly instructions for a final drive in 13 steps, removing components like bolts, gears, and covers. Installation requires cleaning, applying sealant, and torquing bolts to specified values.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It describes 27 steps to disassemble the motor by removing components like the motor head, springs, brake piston, rotating assembly, bearings and seals. It then describes 28 steps for reassembling the motor components in reverse order, making sure to align parts properly, apply lubricants to seals and mating surfaces, and torque bolts to the specified values. The proper procedure is important to safely release spring forces and prevent damage during removal and installation of parts.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring forces or pressurized components.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...fhsjekdmme
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix fbt) service repair manual (fbt000...fhsjekdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar cat 336 d2 l excavator (prefix faj) service repair manual (faj000...fhsjekdmme
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pullers, pry bars, and seal removal tools.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to aid reassembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR FAJ
Configuration: 336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i06605028
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 x 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 88 kg (195 lb).
1/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the heads original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
Example of the use of Tooling (B).
3/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (D) to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press to remove bearing race (18) from shaft (15).
Illustration 13 g03870797
16. Rotate shaft (15). Use a suitable press and Tooling (E) to remove bearing race (19) from
shaft (15).
Illustration 14 g03870686
17. Remove cam plate (20) from barrel assembly (16).
6/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g03870754
18. Remove piston assemblies and retainer plate (21) from barrel assembly (16).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g03870760
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (22) and springs (23).
7/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g03870766
20. Remove bearing (24).
21. Remove keys (25) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g03870770
22. Rotate the housing. Use Tooling (F) to remove retaining ring (26).
23. Remove lip seal (27).
Illustration 19 g03870778
24. Remove bolts (28) and cover (29).
8/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g03870779
25. Remove seal (30) and backup ring (31).
Illustration 21 g03870780
26. Remove piston actuator (32) and seal (33).
Illustration 22 g03870784
27. Remove O-ring seal (34) from the housing of the travel motor.
9/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR FAJ
Configuration: 336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR FAJ
Configuration: 336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
336D 2L and 340D 2L Excavators Machine Systems
Media Number -M0065626-02 Publication Date -01/09/2015 Date Updated -14/12/2017
i06242093
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 243 -
1/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g03870784
1. Install O-ring seal (34) onto the housing of the travel motor.
Illustration 2 g03870780
2. Install seal (33) and piston actuator (32). Lubricate the surfaces of piston actuator (32) with
lubricant that is being sealed.
Illustration 3 g03870779
3. Install backup ring (31) and seal (30).
2/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 4 g03870778
4. Install cover (29) and bolts (28). Tighten bolts (28) to a torque of 28 ± 7 N·m
(248 ± 62 lb in).
Illustration 5 g03870770
5. Apply Tooling (G) to the mating surface of lip seal (27). Use Tooling (E) in order to install
lip seal (27). Lubricate the sealing lip of lip seal (27) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (26).
Illustration 6 g03870766
3/10
336D2, 336D2 L & 336D2 GC Excavators FAJ00001-UP (MACHINE) POWERED B...
2020/8/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...