1. The document provides instructions for disassembling and assembling a piston pump and piston motor that are part of a hydraulic fan system.
2. The disassembly process involves using various tools to remove individual components like bearings, seals, springs, and housings.
3. The assembly process lists the components and specifies the order and method for installing each part, ensuring correct orientation and positioning. Proper cleaning of parts is emphasized.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing bearings, seals, pistons, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts to access the motor. Safety precautions are provided throughout regarding spring-loaded parts that could cause injury.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble and reassemble the pump. These include removing housing components, seals, bearings, pistons, springs and other internal parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 336 d l excavator (prefix ppn) service repair manual (ppn0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for a 336D L & 336D LN excavator. The disassembly procedure involves 30 steps that remove components like the head, port plate, bearing cups, pistons, pins, and springs. The assembly procedure involves 25 steps that install components in the reverse order, and notes that cleanliness is important during assembly. Tools required include retaining ring pliers, a dial indicator, and a bearing puller.
Caterpillar cat 336 d l excavator (prefix zml) service repair manual (zml0000...fjjskekdm
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools to remove retaining rings and springs from compressed locations.
3. Dismantling the rotating group, swashplate, shaft and other internal components.
The instructions aim to safely remove all parts from the piston pump for maintenance or repair. Cleanliness and wearing protective equipment are emphasized.
Caterpillar cat 336 d l excavator (prefix mds) service repair manual (mds0000...fksjksmmde
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools like retaining ring pliers and a driver group to remove springs and retaining rings.
3. Taking safety precautions as parts are under spring tension.
4. Cleaning all parts thoroughly before assembly.
The document provides instructions for assembling a hydraulic lockout control. It describes 17 steps to assemble a piston motor, including installing bearings, seals, springs, and retaining rings. It also outlines 5 steps to disassemble a hydraulic lockout control, such as removing pins and springs. The assembly process is then described in 6 steps, including installing springs, pins, and lever assemblies. Personal injury warnings are provided throughout.
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing various bearings, seals, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts. Cleanliness is emphasized throughout assembly and disassembly. Required tools are listed.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fjjskekdmmem
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 29 steps to disassemble the pump, including removing bolts, seals, bearings, pistons, springs and other components. The assembly procedure is described as installing these components in reverse order while taking precautions for spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing bearings, seals, pistons, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts to access the motor. Safety precautions are provided throughout regarding spring-loaded parts that could cause injury.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble and reassemble the pump. These include removing housing components, seals, bearings, pistons, springs and other internal parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 336 d l excavator (prefix ppn) service repair manual (ppn0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for a 336D L & 336D LN excavator. The disassembly procedure involves 30 steps that remove components like the head, port plate, bearing cups, pistons, pins, and springs. The assembly procedure involves 25 steps that install components in the reverse order, and notes that cleanliness is important during assembly. Tools required include retaining ring pliers, a dial indicator, and a bearing puller.
Caterpillar cat 336 d l excavator (prefix zml) service repair manual (zml0000...fjjskekdm
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools to remove retaining rings and springs from compressed locations.
3. Dismantling the rotating group, swashplate, shaft and other internal components.
The instructions aim to safely remove all parts from the piston pump for maintenance or repair. Cleanliness and wearing protective equipment are emphasized.
Caterpillar cat 336 d l excavator (prefix mds) service repair manual (mds0000...fksjksmmde
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools like retaining ring pliers and a driver group to remove springs and retaining rings.
3. Taking safety precautions as parts are under spring tension.
4. Cleaning all parts thoroughly before assembly.
The document provides instructions for assembling a hydraulic lockout control. It describes 17 steps to assemble a piston motor, including installing bearings, seals, springs, and retaining rings. It also outlines 5 steps to disassemble a hydraulic lockout control, such as removing pins and springs. The assembly process is then described in 6 steps, including installing springs, pins, and lever assemblies. Personal injury warnings are provided throughout.
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing various bearings, seals, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts. Cleanliness is emphasized throughout assembly and disassembly. Required tools are listed.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fjjskekdmmem
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 29 steps to disassemble the pump, including removing bolts, seals, bearings, pistons, springs and other components. The assembly procedure is described as installing these components in reverse order while taking precautions for spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskmdmem
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the pump with 30 parts in 29 steps, requiring cleaning of parts, application of specific temperatures, and use of tools including retaining ring pliers and a dial indicator. Safety precautions are provided throughout regarding spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section lists 14 steps and specifies torque values and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in supporting tables throughout.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque specifications are provided for reinstallation.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
More Related Content
Similar to Caterpillar cat 336 d2 excavator (prefix tly) service repair manual (tly00001 and up)
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskmdmem
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the pump with 30 parts in 29 steps, requiring cleaning of parts, application of specific temperatures, and use of tools including retaining ring pliers and a dial indicator. Safety precautions are provided throughout regarding spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Similar to Caterpillar cat 336 d2 excavator (prefix tly) service repair manual (tly00001 and up) (6)
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section lists 14 steps and specifies torque values and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in supporting tables throughout.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque specifications are provided for reinstallation.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l vg excavator (prefix sdm) service repair manual (sdm...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l vg excavator (prefix pfd) service repair manual (pfd...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided regarding cleaning, marking parts, and applying lubricant before assembly.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...fjskekxcddmmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02732015
Piston Pump (Hydraulic Fan) - Assemble
SMCS - 1387-016-QP; 5070-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 8T-5096 Dial Indicator Gp 1
Illustration 1 g01212915
1. Lower the temperature of bearing cup (49). Install bearing cup (49).
1/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01212913
2. Install lip seal (48).
3. Use Tooling (B) in order to install retaining ring (47).
Illustration 3 g01213404
4. Raise the temperature of bearing cone (46).
5. Install bearing cone (46) onto shaft (45).
Illustration 4 g01213405
6. Install bearing cone (46), shaft (45), and bearing cone (31).
2/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01213407
7. Lower the temperature of bearing cone (26). Install bearing cone (26).
Illustration 6 g01212900
8. Position head (23) onto the housing.
9. Install bolts (22).
Illustration 7 g01213409
10. Use Tooling (D) in order to determine the end play of shaft (45).
3/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g01212900
11. Remove bolts (22) and head (23).
Illustration 9 g01213405
12. Remove bearing cone (31).
Illustration 10 g01213433
13. Install bearings (44).
4/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g01212910
14. Install swashplate (43).
Illustration 12 g01373818
15. Install shim (40), spring (41), and shim (42) to barrel (38).
Illustration 13 g01212908
5/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
16. Use Tooling (A), Tooling (B), and a suitable press in order to install retaining ring (39) into
barrel (38).
Illustration 14 g01212907
17. Install pins (37) into barrel (38).
Illustration 15 g01212906
18. Install bearing (36), retainer (35), and pistons (34).
6/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 16 g01212905
19. Install rotating group (32) and shim (33).
Note: Shim thickness was determined on Step 9.
Illustration 17 g01212904
20. Install bearing cone (31).
Illustration 18 g01212903
21. Install piston (30).
7/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 19 g01212902
22. Install spring (27), piston (29), and O-ring seal (28).
Illustration 20 g01213436
23. Install O-ring seals (24) and port plate (25).
Illustration 21 g01212900
8/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install head (23) and bolts (22).
Illustration 22 g01212898
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Install spool (15), poppet (16), spring (17), spring (18), shim (19), O-ring seal (20), and
housing (21) into housing (2).
26. Install retainer (7), spring (8), retainer (9), spool (10), O-ring seal (12), backup ring (11), O-
ring seal (13), and cartridge (14).
27. Install screw (6) into housing (2).
9/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g01212897
28. Install coil (4) and nut (5).
Illustration 24 g01212896
29. Install O-ring seals (3).
Illustration 25 g01212895
30. Install controller (2) and bolts (1).
End By:
10/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 En...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan)
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 19:55:55 UTC+0800 2020
11/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 En...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02424411
Piston Pump (Hydraulic Fan) - Install
SMCS - 1387-012-QP; 5070-012-HFN
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01211400
1. Position piston pump (7) and install bolts (6).
2. Connect harness assembly (5).
3. Connect hose assemblies (3) and (4).
1/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01211399
4. Connect hose assembly (2).
Illustration 3 g01206719
5. Close door (1).
6. Fill the hydraulic system with oil. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 19:56:51 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415451
Piston Motor (Hydraulic Fan) - Remove
SMCS - 1386-011-QP; 5058-011-FM
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01207415
1. Bend locking tabs (1) backward.
2. Remove bolts (2) and hub (3).
1/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01207416
3. Use a suitable lifting device to position fan motor assembly (4) onto suitable cribbing. The
weight of fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207418
4. Attach a suitable lifting device to piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
5. Remove bolts (6) and fan motor (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 19:57:47 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415272
Piston Motor (Hydraulic Fan) - Disassemble
SMCS - 1386-015-QP; 5058-015-FM; 5058-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Start By:
a. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Remove".
1/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01207275
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and head (2).
Illustration 2 g01207276
2. Remove O-ring seal (3), port plate (4), and bearing cup (5).
Illustration 3 g01207278
2/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (6), sleeve (7), poppet (8), spring (9), poppet (10), and O-ring seal (11).
Illustration 4 g01207279
4. Remove bearing cone (12).
Illustration 5 g01207280
5. Remove shim (13) and rotating group (14).
3/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 9 g01207284
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Use Tooling (C) and Tooling (B) in order to remove retaining ring (19).
10. Remove shim (23), spring (22), and shim (21).
Illustration 10 g01207285
11. Remove swashplate (24) and shaft (25).
5/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 11 g01207287
12. Use Tooling (A) in order to remove bearing cone (26) from shaft (25).
Illustration 12 g01207286
13. Use Tooling (C) in order to remove retaining ring (27).
14. Remove lip seal (28).
Illustration 13 g01207288
15. Remove bearing cup (29).
6/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...