This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. It describes cleaning grease from the swing gear and bearing, marking them for alignment during reinstallation, attaching lifting tools, using a hydraulic torque wrench to remove bolts and spacers, and lifting out the swing gear and bearing assembly which weighs approximately 280 kg. Cleaning and inspection of parts is recommended before reassembly.
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper tools are required and safety notes are provided regarding cleanliness and part weights which can be substantial.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 326 d2 l excavator (prefix jfl) service repair manual (jfl000...fjsekdmmeed
This document provides instructions for disassembling and assembling the travel motor of an excavator model 326D2 L. The disassembly procedure involves removing 28 different components of the travel motor in sequential order, including the head, port plate, springs, brake piston, plates, seals, and housing cover. The assembly procedure instructs installing these same components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper alignment and torque specifications are identified.
This document provides instructions for disassembling and assembling the rear axle of a M315D2 wheeled excavator. It lists required tools and gives step-by-step instructions for removing and installing various components of the final drive carriers, hubs, and brakes. This includes removing retaining rings, planetary gears, thrust washers, bearings, pistons, seals, and other parts. Precautions are provided regarding contained fluids, spring forces, and torque specifications for reassembly.
Caterpillar cat 336 d l excavator (prefix l5x) service repair manual (l5x0000...fjskemdme
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 336D L excavator. The removal process involves using tools to remove bolts, bushings, bearings, gears and other components. Dimensions for installing replacement bearings are also specified. Proper cleaning and application of threadlock are emphasized during installation.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It describes 33 steps to remove components such as plugs, springs, seats, spools, adapters, valves and seals. Special care must be taken when removing pressurized components to avoid injury from parts propelled by released spring forces. Cleanliness is important to prevent contamination during disassembly.
This document provides instructions to remove and install the final drive and travel motor on a 323D3 excavator. The key steps are:
1. Position the final drive and travel motor in a cribbing and remove attachment bolts and covers.
2. Use pullers and eyebolts to separate the housing from the travel motor.
3. Remove seals, bearings, and other components from the housing and travel motor.
4. Clean all parts thoroughly and inspect for wear. Replace any worn parts.
5. Reassemble by installing bearings, seals and other components back into the housing and travel motor.
6. Apply anti-seize lubricant and use presses
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper tools are required and safety notes are provided regarding cleanliness and part weights which can be substantial.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 326 d2 l excavator (prefix jfl) service repair manual (jfl000...fjsekdmmeed
This document provides instructions for disassembling and assembling the travel motor of an excavator model 326D2 L. The disassembly procedure involves removing 28 different components of the travel motor in sequential order, including the head, port plate, springs, brake piston, plates, seals, and housing cover. The assembly procedure instructs installing these same components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper alignment and torque specifications are identified.
This document provides instructions for disassembling and assembling the rear axle of a M315D2 wheeled excavator. It lists required tools and gives step-by-step instructions for removing and installing various components of the final drive carriers, hubs, and brakes. This includes removing retaining rings, planetary gears, thrust washers, bearings, pistons, seals, and other parts. Precautions are provided regarding contained fluids, spring forces, and torque specifications for reassembly.
Caterpillar cat 336 d l excavator (prefix l5x) service repair manual (l5x0000...fjskemdme
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 336D L excavator. The removal process involves using tools to remove bolts, bushings, bearings, gears and other components. Dimensions for installing replacement bearings are also specified. Proper cleaning and application of threadlock are emphasized during installation.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It describes 33 steps to remove components such as plugs, springs, seats, spools, adapters, valves and seals. Special care must be taken when removing pressurized components to avoid injury from parts propelled by released spring forces. Cleanliness is important to prevent contamination during disassembly.
This document provides instructions to remove and install the final drive and travel motor on a 323D3 excavator. The key steps are:
1. Position the final drive and travel motor in a cribbing and remove attachment bolts and covers.
2. Use pullers and eyebolts to separate the housing from the travel motor.
3. Remove seals, bearings, and other components from the housing and travel motor.
4. Clean all parts thoroughly and inspect for wear. Replace any worn parts.
5. Reassemble by installing bearings, seals and other components back into the housing and travel motor.
6. Apply anti-seize lubricant and use presses
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f8uejkdkdmm3e
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...jfdjskmdmme
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...fjjsekkksmeik
The document provides instructions for assembling a swing drive for an excavator model 330D L. The assembly process involves 28 steps including installing bearings and seals into housings, pressing gears and shafts into place, applying sealants, and torquing bolts to specification. Precision and cleanliness are important to ensure proper assembly and prevent future issues. The completed swing drive unit is then installed onto the excavator frame.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...cdfzxs
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...diskdkkdmmd
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housing components, and fasteners in the proper sequence. The assembled swing drive is then installed on the excavator frame using lifting equipment and bolted into place with an alternating tightening pattern to the specified torque.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fuusejkddmmd3e
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...shibi1322
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...fucheng89
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...dujkdksmdmdm
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...jdksmmdmdd
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
More Related Content
Similar to Caterpillar cat 336 d l excavator (prefix m3n) service repair manual (m3n00001 and up)
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f8uejkdkdmm3e
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...jfdjskmdmme
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...fjjsekkksmeik
The document provides instructions for assembling a swing drive for an excavator model 330D L. The assembly process involves 28 steps including installing bearings and seals into housings, pressing gears and shafts into place, applying sealants, and torquing bolts to specification. Precision and cleanliness are important to ensure proper assembly and prevent future issues. The completed swing drive unit is then installed onto the excavator frame.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...cdfzxs
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...diskdkkdmmd
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housing components, and fasteners in the proper sequence. The assembled swing drive is then installed on the excavator frame using lifting equipment and bolted into place with an alternating tightening pattern to the specified torque.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fuusejkddmmd3e
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...shibi1322
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...fucheng89
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...dujkdksmdmdm
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...jdksmmdmdd
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
Similar to Caterpillar cat 336 d l excavator (prefix m3n) service repair manual (m3n00001 and up) (12)
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper order. It also provides disassembly instructions for a final drive in 13 steps, removing components like bolts, gears, and covers. Installation requires cleaning, applying sealant, and torquing bolts to specified values.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It describes 27 steps to disassemble the motor by removing components like the motor head, springs, brake piston, rotating assembly, bearings and seals. It then describes 28 steps for reassembling the motor components in reverse order, making sure to align parts properly, apply lubricants to seals and mating surfaces, and torque bolts to the specified values. The proper procedure is important to safely release spring forces and prevent damage during removal and installation of parts.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring forces or pressurized components.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...fhsjekdmme
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix fbt) service repair manual (fbt000...fhsjekdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar cat 336 d2 l excavator (prefix faj) service repair manual (faj000...fhsjekdmme
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pullers, pry bars, and seal removal tools.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D MOBILE HYD POWER UNIT M3N
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06939513
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-5197 Pliers 1
B 138-7574 Link Brackets 2
C 138-7575 Link Bracket 3
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00869899
1. Install lip seals (32) and O-ring seal (33) in bearing cage (29).
Illustration 2 g00870134
Note: Lubricate the seals and the seal surface of the shaft before you install the cage
assembly.
2. Carefully install cage (29) on shaft (31).
Illustration 3 g00870142
3. Raise the temperature of bearing (36) to 135 °C (275 °F) and use two people to install the
bearing on shaft (31). The weight of bearing (36) is approximately 35 kg (77 lb).
4. Install spacer (35) on shaft assembly (31). Install the spacer with relief against bearing (36).
2/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00870160
5. Raise the temperature of bearing (34) to 135 °C (275 °F). Install the bearing on shaft (31)
and against spacer (35).
Illustration 5 g00870169
6. Use Tooling (A) to install retaining ring (28) on shaft (31) and against bearing (34).
Illustration 6 g01041406
7. Install shaft assembly (31) in swing drive housing (16).
3/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. a. Apply 5P-3931 Anti-Seize Compound on the inside diameter of swing drive housing
(16).
b. Lower the temperature of shaft assembly (31).
c. Attach Tooling (C) and a suitable lifting device to the shaft assembly.
d. Install the shaft assembly into swing drive housing (16). Bearing (34) must be within
the bore of the swing drive housing.
e. Remove Tooling (C) and the suitable lifting device from the shaft assembly. Attach
Tooling (C) and the suitable lifting device to the swing drive housing.
f. Lift the swing drive vertically. Use a hammer and a drift to align bearing (34) in the
lower bore of the swing drive housing. When the bearing is properly aligned in the
bore, shaft assembly (31) will drop into the proper position within the swing drive
housing.
Illustration 7 g00870264
8. Apply 1U-8846 Sealant on the threads of bolts (30).
9. Install bolts (30) and washers in bearing cage (29) and swing drive housing (16).
Illustration 8 g00869483
4/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00870281
10. Install bearings (24) and (26) in gear (25).
11. Install gear (25) and washers (23) and (27) in carrier (20).
12. Lower the temperature of shaft (22). Install the shaft in carrier assembly (20).
13. Install pin (21) in the carrier assembly and the shaft.
14. Use a hammer and a center punch to stake the pin in the carrier housing.
15. Repeat Steps 10 through Steps 14 on the remaining gear assemblies.
Illustration 10 g00869464
16. Use a suitable lifting device to install carrier assembly (20). The weight of carrier assembly
(20) is approximately 68 kg (150 lb).
5/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00869460
17. Install retaining ring (19).
Illustration 12 g00869406
18. Install spacer (17) in carrier assembly (18).
Illustration 13 g00869390
19. Make sure that the mating surfaces of ring gear (15) and swing drive housing (16) are
thoroughly clean.
6/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 20. Apply 1U-8846 Gasket Sealant to the face of swing drive housing (16) and the face of ring
gear (15).
21. Use Tooling (B) and a suitable lifting device to install ring gear (15) in swing drive housing
(16). The weight of ring gear (15) is approximately 80 kg (175 lb).
Illustration 14 g00869383
22. Install retaining ring (14) into the sun gear.
Illustration 15 g00869377
23. Install sun gear (13) in carrier assembly (4). Install upper retaining ring (12).
24. Assemble carrier assembly (4).
7/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00869315
a. Apply clean SAE 30W oil on bearing (10). Install bearing (10) in planetary gear (9).
b. Install thrust washer (8) on one side of planetary gear (9).
c. Install thrust washer (11) on the other side of planetary gear (9).
d. Use a deburring tool to remove the metal burr from the openings in the carrier.
e. Install planetary gear (9) and the thrust washers in carrier assembly (4).
Illustration 17 g00869309
f. Install planetary shaft (7) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
Illustration 18 g00703700
8/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. g. Drive spring pin (6) into shaft (7). Orient the split in spring pin (6) vertically to the
carrier. Align the split in the spring pin to the top or the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 24.a through 24.g to install the other three planetary gears in the carrier.
Illustration 19 g00869294
25. Use two people to install carrier assembly (4) in the ring gear. The weight of the carrier
assembly is approximately 36 kg (80 lb).
26. Install spacer (5) in carrier assembly (4).
Illustration 20 g00869281
27. Install sun gear (3) in carrier assembly (4).
9/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00869266
28. Make sure that the mating surfaces of the ring gear and cover (2) are thoroughly clean.
29. Apply 1U-8846 Gasket Sealant on the flange surface of the ring gear and cover (5).
30. Install cover (2) and bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 09:57:19 UTC+0800 2020
10/10
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POW...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D MOBILE HYD POWER UNIT M3N
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07192381
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 439-3939 Link Bracket As 4
C -
Forcing Bolt
M24 x 3 by 5 inch
2
D - Loctite C5A Copper Anti-Seize -
E 1U-8846 Gasket Sealant 1
1. Apply Tooling (D) on the locating pin and the pin bore in the main frame. Apply Tooling
(E) on the mating surface of the main frame and the swing drive housing.
1/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00875735
2. Attach Tooling (B) and a suitable lifting device to swing drive (2), as shown. The weight of
swing drive (2) is approximately 510 kg (1125 lb). Install swing drive (2) into the original
position. Be careful not to damage the pinion gear.
Note: During installation, the locating pin for the swing drive can come out of the swing
drive housing. The locating pin can be installed with a hammer after the swing drive is in
place.
Illustration 2 g01206242
3. Use Tooling (A) to install bolts (1) that secure the swing drive to the main frame.
4. Before assembly, remove compound, oil, and dust from female threads, then apply Tooling
(D) to the threads of bolts (1).
5. Tighten bolts (1) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
6. Fill the swing drive with oil. Refer to Operation and Maintenance Manual, "Swing Drive Oil
- Change".
End By:
2/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install"
.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 09:58:15 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D MOBILE HYD POWER UNIT M3N
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02386587
Swing Gear and Bearing - Remove
SMCS - 7063-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7576 Link Bracket 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Start By:
a. Remove the undercarriage frame. Refer to Disassembly and Assembly, "Upper Frame and
Undercarriage Frame - Separate".
1. Remove all of the grease from the swing gear and bearing. Put the grease in a suitable
container for storage or disposal.
1/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00520664
2. Put an alignment mark on swing gear and bearing (1) and on the undercarriage frame
assembly for assembly purposes. Attach Tooling (A) and a suitable lifting device to swing
gear and bearing (1), as shown. Apply slight lifting tension to the swing gear and bearing.
Illustration 2 g00520670
3. Use Tooling (B) in order to remove bolts (2) and the spacers that hold swing gear and
bearing (1) to the undercarriage frame.
4. Remove swing gear and bearing (1). The weight of the swing gear and bearing (1) is
approximately 280 kg (615 lb).
2/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00721855
Note: Inner dust seal (3) and outer dust seal (4) may have been installed dry in the swing
gear and bearing or inner dust seal (3) and outer dust seal (4) may have been bonded to the
swing gear and bearing.
5. Remove inner dust seal (3) and outer dust seal (4) from the swing gear and bearing.
6. Clean the seal grooves of the inner dust seal and the outer dust seal with a fine grit
sandpaper. Use a cleaning solvent to clean the sealing grooves. Make sure that the seal
grooves are thoroughly clean and dry prior to installing the new dust seals.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 09:59:11 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D MOBILE HYD POWER UNIT M3N
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07191587
Swing Gear and Bearing - Install
SMCS - 7063-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3941 Link Bracket As 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
C - Loctite 435 -
D 2P-9066 Lubricant 1
E 1U-8846 Gasket Sealant 1
F - Loctite C5A Copper Anti-Seize -
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Note: If the inner dust seal (3) and the outer dust seal (4) are installed dry, the new dust seals should
be installed dry in the swing gear and bearing.
Note: If the inner dust seal and the outer dust seal are bonded to the swing gear and bearing, the new
dust seals should be bonded to the swing gear and bearing.
Note: Perform Steps 1.a through 1.j to install the new dry dust seals.
Note: Perform Steps 2.a through 2.p to install the new dust seals that are bonded to the swing gear
and bearing.
1/6
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00636223
1. If inner dust seal (3) and outer dust seal (4) were installed dry, use the following procedure to install
the new dust seals:
a. Use a wire brush to thoroughly clean the grooves for the dust seal of the swing gear and
bearing. Make sure that all the dirt and foreign material has been removed.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seal in the swing gear and bearing are thoroughly clean
and dry prior to installation of the dust seals.
d. Cut one end of inner dust seal (3) at a 90 degree angle. Use a blunt tool to install the inner dust
seal in the seal groove of the swing gear and bearing.
e. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
f. After the inner dust seal is installed in the seal groove, measure the seal and cut the remaining
end of the inner dust seal at a 90 degree angle. Install the remaining end of the inner dust seal
in the seal groove.
g. Make sure that the inner dust seal is seated properly in the seal groove, all the way around the
swing gear and bearing. Also, make sure that there is no gap between the ends of the inner dust
seal.
h. Pull each end of the inner dust seal out of the seal groove of the swing gear and bearing
approximately 50.8 mm (2.00 inch). Apply Tooling (C) to each end of the inner dust seal to
bond the seals together.
i. Immediately reinstall the inner dust seal in the seal groove of the swing gear and bearing.
Again, make sure that the entire inner dust seal is properly seated in the seal groove of the
swing gear and bearing. No gap should exist between the ends of the inner dust seal.
j. To ensure that the lip of inner dust seal has not adhered to the top of the bearing at the seal
joint, run a dull putty knife between the lip of the seal and the bearing at the seal joint.
k. Follow the procedure in Steps 1.a through 1.j to install outer dust seal (4) in the swing gear and
bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
2/6
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 2. If inner dust seal (3) and outer dust seal (4) were bonded in the swing gear and bearing, use the
following procedure to install the new dust seals:
a. Thoroughly clean all the dirt and foreign material from the grooves for the dust seal in the
swing gear and bearing with a wire brush.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seals in the swing gear and bearing are thoroughly
clean and dry prior to installation of the dust seals.
Note: Install inner dust seal (3) and outer dust seal (4) in the swing gear and bearing in small
increments, because Tooling (C) cures very quickly.
d. Cut one end of inner dust seal (3) at a 90 degree angle.
e. Start applying Tooling (C) 50.8 mm (2.00 inch) from the cut end of the seal. Apply Tooling
(C) to the seal in 152.4 mm (6.00 inch) increments.
f. Immediately use a blunt tool to install only the bonded portion of the inner dust seal in the seal
groove of the swing gear and bearing. Make sure that the dust seal is seated properly in the
seal groove.
g. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
h. To ensure that the inner dust seal has not adhered to the bearing, run a dull putty knife between
the lip of the seal and the bearing.
i. Apply Tooling (C) to the next 152.4 mm (6.00 inch) of the seal. Immediately use a blunt tool
to install only the bonded portion of the inner dust seal in the seal groove of the swing gear and
bearing.
j. Make sure that the inner dust seal is seated properly in the seal groove. Ensure that the inner
dust seal has not adhered to the bearing.
Note: Do not install the last 152.4 mm (6.00 inch) of the inner dust seal.
k. Repeat Steps 2.i through 2.j until the dust seal is installed.
l. Measure the inner dust seal and cut the remaining end of inner dust seal (3) at a 90 degree
angle. Install the last 152.4 mm (6.00 inch) of seal in the seal groove dry.
m. Make sure that the inner dust seal is properly seated in the seal groove and that there is no gap
between the seal ends. Carefully remove both loose ends of the inner dust seal out of the seal
groove.
n. Apply Tooling (C) to the loose ends of the seal.
o. Immediately use a blunt tool to reinstall the seal ends in the seal groove. Again, make sure that
the inner dust seal is properly seated in the seal groove, and that no gap existed between the
ends of the seal.
p. To ensure that the inner dust seal has not adhered to the top of the bearing, run a dull putty
knife around the seal.
q. Follow the procedure in Steps 2.a through 2.p to install outer dust seal (4) in the swing gear
and bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
3. Lubricate the swing gear and bearing with grease.
3/6
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g00520664
Illustration 3 g00520674
Note: Clean the mating surface for the swing gear and bearing on the undercarriage frame assembly.
4. Apply Tooling (E) on the mating surface for the swing gear and bearing of the undercarriage frame
assembly.
5. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Refer to
Illustration 2. The weight of swing gear and bearing (1) is approximately 660 kg (1455 lb).
6. Place the swing gear and bearing in the swing gear and bearing's original position on the
undercarriage frame assembly.
7. Make sure that the stamp "S" on the inner race is in the position that is shown, relative to the
undercarriage frame assembly and the stopper on the outer race. Refer to Illustration 3.
4/6
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g00520670
8. Apply a thin coat of Tooling (F) on the threads of bolts (2). Install the spacers and bolts (2) that
secure the swing gear and bearing to the undercarriage frame assembly.
Note: Some machines use bolts that are plated with Dacromet. Dacromet bolts appear silver, gray in
color. Do not apply Tooling (F) to the threads of Dacromet bolts. Make sure that the bolt holes are
clean and dry when Dacromet bolts are used.
Note: Torque for bolts (2) is 1000 ± 125 N·m (738 ± 92 lb ft) on 345 excavators.
Note: Torque for bolts (2) is 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional angle of 55 ± 5
degrees on 336 excavators.
9. Use Tooling (B) to tighten bolts (2) to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
10. Refer to Service Magazine , M0083843 , "An Improved Bolt Tightening Procedure for the Critical
Joints Is Now Used on all Excavators" for more detailed information.
NOTICE
Improper lubrication can cause damage to machine components.
To avoid damage, make sure that the proper amount of grease is
applied to the swing drive.
When the amount of grease in the compartment becomes too large, the
agitation loss becomes large, thereby accelerating grease deterioration.
Grease deterioration can cause damage to the pinion gear of the swing
drive and swing internal gear.
Not enough grease will result in poor gear lubrication.
11. Add Tooling (D) to the swing gear and bearing after the installation.
Reference: Refer to Operation and Maintenance Manual, "Refill Capacities" for the capacity of the
swing gear and bearing.
Reference: Refer to Operation and Maintenance Manual, "Swing Gear - Lubricate" for lubricating
the swing gear and bearing.
5/6
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Reference: Refer to Operation and Maintenance Manual, "Maintenance Interval Schedule" for the
schedule for lubricating the swing gear and bearing.
End By:
a. Install the undercarriage frame assembly. Refer to Disassembly and Assembly, "Undercarriage
Frame - Install" in this manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 10:00:07 UTC+0800 2020
6/6
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D MOBILE HYD POWER UNIT M3N
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02451315
Oil Filter (Hydraulic, Return) - Remove
SMCS - 5068-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
1. Drain the hydraulic oil into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Hydraulic Oil - Change".
Illustration 1 g01218778
1/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. 2. Remove bolts (1) and reposition filter assembly (2).
Illustration 2 g01218865
3. Disconnect hose assemblies (4). Remove bolts (3). Reposition filter assembly (5) out of the
way.
Illustration 3 g01223795
4. Remove bolts (6) from pipe assembly (7).
Illustration 4 g01218952
2/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g01218954
5. Attach Tooling (A) and a suitable lifting device to oil filter assembly (9). The weight of oil
filter assembly (9) is approximately 20 kg (45 lb). Remove bolts (8). Disconnect harness
assembly (11). Remove bolts (10). Remove oil filter assembly (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 10:01:03 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D MOBILE HYD POWER UNIT M3N
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02451316
Oil Filter (Hydraulic, Return) - Install
SMCS - 5068-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Illustration 1 g01218952
1/3
336D & 336D L Mobile Hydraulic Power Units M3N00001-UP (MACHINE) POWE...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...