This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...shudun96087
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves disconnecting hoses, removing bolts and fittings, and lifting the final drive and travel motor assembly out of the machine. The installation procedure describes reinstalling components in the reverse order and includes precautions for ensuring components are clean and properly torqued.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...shudun96087
The document provides instructions for removing the final drive and travel motor assembly from a 330D L hydraulic excavator. It lists the required tools and safety precautions. The procedure involves applying vacuum pressure to the hydraulic system, disconnecting hoses, and removing bolts to detach the final drive and travel motor assembly using lifting tools. Markings are to be made to ensure correct reinstallation orientation.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...kesi7153062
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves using tools to apply vacuum pressure to the hydraulic system, disconnecting hose assemblies, and removing bolts and fittings. The travel motor and final drive assembly can then be lifted out. The installation procedure specifies cleaning parts and replacing seals before reinstalling components in the reverse order of removal while applying loctite to bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...kesi7153062
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves disconnecting hoses, removing bolts and fittings, and lifting the final drive and travel motor assembly out of the machine. The installation procedure describes reinstalling components in the reverse order and includes precautions for cleanliness and torque specifications. The document is intended to guide maintenance technicians in properly servicing these components.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...cnp692569
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves using tools to apply vacuum pressure to the hydraulic system, disconnecting hose assemblies, and removing bolts and fittings. The travel motor and final drive assembly can then be lifted out. The installation procedure specifies cleaning parts and replacing seals before reinstalling components in the reverse order of removal while applying loctite to bolts.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...cnp692569
This document provides instructions for removing the final drive and travel motor, and the swivel, from a 330D L hydraulic excavator. It lists the required tools and safety precautions. The procedure for removing the final drive and travel motor involves disconnecting hoses, removing bolts, and lifting the component out. Removing the swivel requires releasing hydraulic pressure, disconnecting hoses, and removing a support. Proper containment of fluids and cleaning of parts is emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f8uejkdkdmm3e
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...shudun96087
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves disconnecting hoses, removing bolts and fittings, and lifting the final drive and travel motor assembly out of the machine. The installation procedure describes reinstalling components in the reverse order and includes precautions for ensuring components are clean and properly torqued.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...shudun96087
The document provides instructions for removing the final drive and travel motor assembly from a 330D L hydraulic excavator. It lists the required tools and safety precautions. The procedure involves applying vacuum pressure to the hydraulic system, disconnecting hoses, and removing bolts to detach the final drive and travel motor assembly using lifting tools. Markings are to be made to ensure correct reinstallation orientation.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...kesi7153062
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves using tools to apply vacuum pressure to the hydraulic system, disconnecting hose assemblies, and removing bolts and fittings. The travel motor and final drive assembly can then be lifted out. The installation procedure specifies cleaning parts and replacing seals before reinstalling components in the reverse order of removal while applying loctite to bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...kesi7153062
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves disconnecting hoses, removing bolts and fittings, and lifting the final drive and travel motor assembly out of the machine. The installation procedure describes reinstalling components in the reverse order and includes precautions for cleanliness and torque specifications. The document is intended to guide maintenance technicians in properly servicing these components.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...cnp692569
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves using tools to apply vacuum pressure to the hydraulic system, disconnecting hose assemblies, and removing bolts and fittings. The travel motor and final drive assembly can then be lifted out. The installation procedure specifies cleaning parts and replacing seals before reinstalling components in the reverse order of removal while applying loctite to bolts.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...cnp692569
This document provides instructions for removing the final drive and travel motor, and the swivel, from a 330D L hydraulic excavator. It lists the required tools and safety precautions. The procedure for removing the final drive and travel motor involves disconnecting hoses, removing bolts, and lifting the component out. Removing the swivel requires releasing hydraulic pressure, disconnecting hoses, and removing a support. Proper containment of fluids and cleaning of parts is emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f8uejkdkdmm3e
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fuusejkddmmd3e
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and tightening fasteners to the specified torque. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...shibi1322
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system before disassembly. Precautions are listed for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...fucheng89
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and apply vacuum pressure to the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...dujkdksmdmdm
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts, and removing mounting bolts and seals.
3. Reinstalling seals and components in reverse order, and refilling the hydraulic system. Proper cleaning, safety procedures, and use of anti-seize compound are emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...jdksmmdmdd
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...diskdkkdmmd
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts.
3. Removing sealing rings and the counterbalance valve.
4. Reinstalling involves the reverse of removal steps, including applying anti-seize compound and tightening bolts to the specified torque.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...orrf0370383
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system before disassembly. Precautions are listed for containing fluids and preventing contamination.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...jfdjskmdmme
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and fasteners, and refilling fluids. Proper torque and sequencing is required.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...cdfzxs
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to install the components in reverse order. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...fjjsekkksmeik
This document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. The removal process involves: releasing hydraulic pressure, separating the track, removing hoses and fittings, attaching lifting tools, and removing mounting bolts. The installation is the reverse of removal, and includes checking seals, applying anti-seize compound, reconnecting hoses, filling the hydraulic system, and reinstalling covers. A separate section provides instructions for removing the swivel assembly, which involves disconnecting hoses, attaching lifting tools, and removing retaining bolts.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...cdsaas
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and fasteners, and refilling fluids. Proper torque and sequencing is required.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...shudun96087
The document provides instructions for removing and disassembling the swivel component of an excavator. Key steps include:
1. Releasing hydraulic pressure and disconnecting hose assemblies.
2. Removing bolts and covers to access the swivel.
3. Lifting the swivel out after disconnecting remaining fittings and hoses.
4. Cleaning and positioning the swivel on a repair stand for disassembly.
5. Separating the outside housing from the rotor by removing bolts, washers, and other retaining components.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...kesi7153062
The document provides instructions for removing and disassembling the swivel component of an excavator. It lists the required tools and gives step-by-step instructions to: 1) remove the swivel by disconnecting hoses, removing bolts and lifting it out; 2) further disassemble the swivel by cleaning it, mounting it securely, and then removing bolts and seals to separate the outer housing from the inner rotor. Proper containment of fluids and cleaning of parts is emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...cnp692569
The document provides instructions for removing and disassembling the swivel component of an excavator. Key steps include:
1. Releasing hydraulic pressure and disconnecting hose assemblies.
2. Removing bolts and covers to access the swivel.
3. Using lifting devices, removing bolts and separating the outside housing from the rotor to fully disassemble the swivel.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
More Related Content
Similar to Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual (RAS00001 and up).pdf
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fuusejkddmmd3e
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and tightening fasteners to the specified torque. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...shibi1322
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system before disassembly. Precautions are listed for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...fucheng89
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and apply vacuum pressure to the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...dujkdksmdmdm
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts, and removing mounting bolts and seals.
3. Reinstalling seals and components in reverse order, and refilling the hydraulic system. Proper cleaning, safety procedures, and use of anti-seize compound are emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...jdksmmdmdd
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...diskdkkdmmd
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts.
3. Removing sealing rings and the counterbalance valve.
4. Reinstalling involves the reverse of removal steps, including applying anti-seize compound and tightening bolts to the specified torque.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...orrf0370383
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system before disassembly. Precautions are listed for containing fluids and preventing contamination.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...jfdjskmdmme
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and fasteners, and refilling fluids. Proper torque and sequencing is required.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...cdfzxs
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to install the components in reverse order. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...fjjsekkksmeik
This document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. The removal process involves: releasing hydraulic pressure, separating the track, removing hoses and fittings, attaching lifting tools, and removing mounting bolts. The installation is the reverse of removal, and includes checking seals, applying anti-seize compound, reconnecting hoses, filling the hydraulic system, and reinstalling covers. A separate section provides instructions for removing the swivel assembly, which involves disconnecting hoses, attaching lifting tools, and removing retaining bolts.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...cdsaas
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and fasteners, and refilling fluids. Proper torque and sequencing is required.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...shudun96087
The document provides instructions for removing and disassembling the swivel component of an excavator. Key steps include:
1. Releasing hydraulic pressure and disconnecting hose assemblies.
2. Removing bolts and covers to access the swivel.
3. Lifting the swivel out after disconnecting remaining fittings and hoses.
4. Cleaning and positioning the swivel on a repair stand for disassembly.
5. Separating the outside housing from the rotor by removing bolts, washers, and other retaining components.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...kesi7153062
The document provides instructions for removing and disassembling the swivel component of an excavator. It lists the required tools and gives step-by-step instructions to: 1) remove the swivel by disconnecting hoses, removing bolts and lifting it out; 2) further disassemble the swivel by cleaning it, mounting it securely, and then removing bolts and seals to separate the outer housing from the inner rotor. Proper containment of fluids and cleaning of parts is emphasized.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...cnp692569
The document provides instructions for removing and disassembling the swivel component of an excavator. Key steps include:
1. Releasing hydraulic pressure and disconnecting hose assemblies.
2. Removing bolts and covers to access the swivel.
3. Using lifting devices, removing bolts and separating the outside housing from the rotor to fully disassemble the swivel.
Similar to Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual (RAS00001 and up).pdf (17)
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and more. Technicians are advised to clean all parts thoroughly, replace all O-rings and seals, and ensure components are reinstalled in their original locations and orientations. Proper assembly helps prevent contamination and failures.
Caterpillar Cat 345C HCR Material Handler EXCAVATOR (Prefix MTE) Service Repa...f7djidksmd3e
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. It outlines:
1) The required tools and removal procedure for the rear gear group which involves removing bolts, seals, gears, bushings and bearings.
2) The installation procedure for the rear gear group which specifies cleaning, applying lubricant and torque specifications for installing the components in reverse order of removal.
3) The removal procedure for the flywheel which requires attaching lifting equipment and removing bolts and ring gear.
4) The installation procedure for the flywheel which involves heating components, applying threadlocker and torque specifications.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...f7djidksmd3e
This document provides assembly instructions for a travel motor on an excavator model 345B Series II. It outlines 31 steps to assemble components like the head, housing, plates, seals, and pins. Special tools are required for tasks like installing seals. Technicians are advised to clean all parts, replace all seals and O-rings, and correct any conditions that caused prior failures.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...f7djidksmd3e
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and sensors. The cylinder head is then removed using lifting equipment due to its weight of 135 kg. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper specification. Special tools and repair kits are listed for tasks such as tapping threads and installing Helicoil inserts if head bolt threads are damaged.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...f7djidksmd3e
This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing bearings onto the pinion shaft and installing the assembly into the swing drive housing using a press.
4. Temporarily installing bolts to hold the bearing cage aligned with the housing. The instructions provide details on lubricants to use and proper positioning of parts.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...f7djidksmd3e
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing.
2. Remove the rear cover and gasket.
3. Remove the rear power take-off (RPTO) and O-ring seal.
This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, covers, pistons, plates, seals, and housing pieces. Illustrations accompany each step to show how to position the motor and parts for disassembly and reassembly. Safety notices are also included to handle parts and fluids properly.
Caterpillar Cat 340D2 L Excavator (Prefix HHK) Service Repair Manual (HHK0000...f7djidksmd3e
The document provides instructions for disassembling the final drive of an excavator model 340D2 L. It describes 25 steps to remove components such as gears, shafts, seals, bearings and housings. Various tools are required including link brackets and forcing bolts to compress springs. Personal protective equipment is recommended as parts can be propelled by released spring forces. The total weight of the final drive assembly is approximately 550 kg.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...f7djidksmd3e
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing the parts in reverse order of removal.
3) Installing the engine oil filter base on the engine, including attaching hoses and bolts.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and provides details on lubricating parts and ensuring proper alignment of components like the cam plate and brake piston. Special tools are required for tasks like removing the rotating assembly and installing seals and bearings.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f7djidksmd3e
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hoses, removing bolts and other fasteners, and using lifting devices. A 7 step disassembly procedure is also provided which involves cleaning, positioning, and separating the swivel's outer housing and rotor components using bolts, washers, and specialized tooling. Personal protective equipment is recommended when handling fluids.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02451126
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 138-7573 Link Bracket 1
Note: Put identification marks on all hose assemblies, fittings and ports so that all the components
can be reassembled in the original configuration. Plug all of the hose assemblies and cap all of the
fittings. This helps to prevent fluid loss and this helps to keep contaminants from entering the
system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/6(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g01223707
2/6(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. 1. Remove bolts (1) and cover (2).
2. Separate the track. Refer to Disassembly and Assembly, "Track - Seperate".
Illustration 2 g00944947
3. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 3 g01223711
4. Disconnect hose assemblies (3) and remove fitting (4).
3/6(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Illustration 4 g01181911
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb). Put a slight
lifting tension on the final drive and travel motor (5).
Illustration 5 g01181912
6. Remove bolts (6).
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
4/6(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 6 g01181913
7. Use two bolts (6) in order to remove final drive and travel motor (5).
8. Carefully remove final drive and travel motor (5).
9. Remove bolts (6) from the frame.
Illustration 7 g01181914
10. Remove bolts (7) and counterbalance valve (8).
Illustration 8 g01181917
11. Remove O-ring seals (9) and (10).
5/6(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 9 g01181921
12. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
13. Remove bolts (12) that mount travel motor (11) to final drive (13). Remove travel motor
(11).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 14:10:20 UTC+0800 2020
6/6(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07188136
Final Drive and Travel Motor - Install
SMCS - 4050-012; 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 439-3938 Link Bracket 1
D - Loctite C5A Copper Anti-Seize -
Note: Check the O-ring seals for wear or for damage. Replace the O-ring seals, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01181921
1. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
2. Position travel motor (11). Install bolts (12) that mount travel motor (11) to final drive (13).
2/5(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 2 g01181917
3. Install O-ring seals (10) and (9).
Illustration 3 g01181914
4. Install counterbalance valve (8) and bolts (7).
Illustration 4 g01181911
3/5(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 5 g01182266
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb).
6. Carefully position final drive and travel motor (5). Apply Tooling (D) to the threads of bolts
(6).
7. Tighten bolts (6) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
Illustration 6 g01223711
8. Install fitting (4). Connect hose assemblies (3).
4/5(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 7 g00944947
9. Remove Tooling (A). Install the cap onto the hydraulic tank.
10. Fill the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricant Viscosities
and Refill Capacities".
Illustration 8 g01223707
11. Install cover (2) and bolts (1). Tighten bolts (1) to a torque of 130 ± 10 N·m (96 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 14:11:23 UTC+0800 2020
5/5(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434256
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 1 g01209599
1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216069
2. Disconnect hose assemblies (1), (2), and (3). Remove support (4).
Illustration 3 g01216082
2/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. 3. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Remove bolts (6) and retainer (8). Remove clamp (7) and boot
(5).
Illustration 4 g01216099
4. Remove bolts (10) and covers (11).
Illustration 5 g01216098
5. Disconnect hose assemblies (15). Disconnect fitting (16). Disconnect hose assemblies (12).
Remove fittings (14). Remove bolts (13). Remove swivel (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 14:12:26 UTC+0800 2020
3/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02568407
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-3822 Bolt 2
6V-5839 Washer 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 1. Thoroughly clean the outside of the swivel joint prior to disassembly.
Illustration 1 g00633843
Illustration 2 g00633841
2. Use a suitable lifting device to position the swivel joint onto Tooling (B). Fasten the swivel joint to
Tooling (B), as shown. The weight of the swivel joint is approximately 43 kg (95 lb).
3. Remove bolts (1), washers (2), and cover (3) from outside housing (8).
4. Remove O-ring seal (7) from outside housing (8).
5. Remove bolts (4), washers (5), and retainer (6) from rotor (11).
2/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. 6. Use Tooling (A) in order to separate the outside housing (8) from rotor (11). The weight of outside
housing (8) is approximately 20 kg (45 lb). The weight of rotor (11) is approximately 21 kg (46 lb).
7. Remove seals (9) from outside housing (8).
8. Remove O-ring seals (10) from the outside housing (8).
9. Remove plug (13). Remove O-ring seal (12) from plug (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 14:13:29 UTC+0800 2020
3/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02426337
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components,
if necessary.
1/2(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 1 g00633843
1. Install O-ring seal (12) on plug (13). Apply clean hydraulic oil on the seal. Install plug (13).
2. Install seals (9) and O-ring seals (10) into outside housing (8).
3. Carefully install outside housing (8) over rotor (11).
4. Install retainer (6), washers (5), and bolts (4). This holds the rotor (11) and the outside housing (8)
together.
5. Apply clean hydraulic oil on O-ring seal (7). Install the O-ring seal in the outside housing.
6. Install cover (3), washers (2), and bolts (1) that secure the cover.
7. Check the swivel joint for leaks. Plug the drain ports of the inside body. Apply shop air pressure in
the top of the swivel joint and check the swivel joint for leaks. The shop air pressure should be
between 0.2758 MPa (40 psi) and 0.4137 MPa (60 psi).
End By:
a. Install the swivel joint. Refer to Disassembly and Assembly, "Swivel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 14:14:32 UTC+0800 2020
2/2(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434356
Swivel - Install
SMCS - 5060-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Illustration 1 g01216082
1. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Position swivel (9). Install boot (5) and clamp (7). Install
retainer (8) and bolts (6).
1/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 2 g01216069
2. Connect hose assemblies (1), (2), and (3). Install support (4).
Illustration 3 g01216098
3. Install bolts (13). Install fittings (14). Install fitting (16). Connect hose assemblies (15).
Connect hose assemblies (14) and (12) to swivel (9).
Illustration 4 g01216099
4. Install covers (11) and bolts (10).
2/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 5 g01209599
5. Remove Tooling (A).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 14:15:34 UTC+0800 2020
3/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR RAS
Configuration: 330D L & 330D N Hydraulic Excavator RAS00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434311
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Remove
SMCS - 5479-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes
for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g00690963
1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the
hydraulic system.
2/3(W)
w
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...