The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
Caterpillar cat 330 d l excavator (prefix b6h) service repair manual (b6h0000...fjsjekkmdmme
The document provides instructions for installing a hydraulic lockout control which includes 17 steps. It instructs the user to install the control unit using bolts, apply threadlocker, and secure a switch. Proper safety precautions are emphasized including wearing protective equipment when handling parts under spring tension.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...shudun96087
This document provides instructions for removing and installing an operator console on an excavator. It begins by removing the seat and then removing plates (1) and (2). Hoses, lines, wires and tubes are identified and plugged to prevent fluid loss and contamination. Screws are removed from the console mounting brackets and the console is lifted off. Reinstallation follows the removal steps in reverse.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...kesi7153062
This document provides instructions for removing and installing an operator console on an excavator. It begins by removing the seat and then removing plates (1) and (2). Hoses, lines, wires and tubes are identified and plugged to prevent fluid loss and contamination. Screws are removed from the console mounting brackets and the console is lifted off. Reinstallation follows the removal steps in reverse.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...cnp692569
The document provides instructions for assembling and disassembling various components of a 330D L Excavator, including:
1. Assembling the piston motor by installing bearings, seals, pins, and other components in the correct order.
2. Installing the assembled piston motor and fan motor assembly.
3. Removing the hydraulic lockout control by taking out screws, bolts, and disconnecting wires.
4. Disassembling the hydraulic lockout control by removing springs, levers, and other parts.
5. Reassembling the hydraulic lockout control by reversing the disassembly steps.
The document provides instructions for assembling and disassembling components of the gear motor and control valve for a hydraulic generator system on a wheeled excavator model. It describes 12 steps to disassemble the control valve, involving removing springs, seals, plugs and other parts. Separate sections provide installation and removal procedures for the gear motor and control valve.
The document provides instructions for assembling and disassembling components of the gear motor and control valve for a hydraulic generator system on a wheeled excavator model. It describes 12 steps to disassemble the control valve, involving removing springs, seals, plugs and other parts. Separate sections provide installation and removal procedures for the gear motor and control valve.
1) The document provides assembly and disassembly instructions for a control valve and gear motor used in a wheeled excavator.
2) It describes removing and installing various components like seals, springs, plugs, and housings. Torque specifications are provided for fasteners.
3) Technicians are warned to release hydraulic pressure before working and to wear protective equipment when handling spring loaded parts to avoid injury.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fhjsjkdmemm
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and valves. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing matching components. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat 330 d l excavator (prefix b6h) service repair manual (b6h0000...fjsjekkmdmme
The document provides instructions for installing a hydraulic lockout control which includes 17 steps. It instructs the user to install the control unit using bolts, apply threadlocker, and secure a switch. Proper safety precautions are emphasized including wearing protective equipment when handling parts under spring tension.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...shudun96087
This document provides instructions for removing and installing an operator console on an excavator. It begins by removing the seat and then removing plates (1) and (2). Hoses, lines, wires and tubes are identified and plugged to prevent fluid loss and contamination. Screws are removed from the console mounting brackets and the console is lifted off. Reinstallation follows the removal steps in reverse.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...kesi7153062
This document provides instructions for removing and installing an operator console on an excavator. It begins by removing the seat and then removing plates (1) and (2). Hoses, lines, wires and tubes are identified and plugged to prevent fluid loss and contamination. Screws are removed from the console mounting brackets and the console is lifted off. Reinstallation follows the removal steps in reverse.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...cnp692569
The document provides instructions for assembling and disassembling various components of a 330D L Excavator, including:
1. Assembling the piston motor by installing bearings, seals, pins, and other components in the correct order.
2. Installing the assembled piston motor and fan motor assembly.
3. Removing the hydraulic lockout control by taking out screws, bolts, and disconnecting wires.
4. Disassembling the hydraulic lockout control by removing springs, levers, and other parts.
5. Reassembling the hydraulic lockout control by reversing the disassembly steps.
The document provides instructions for assembling and disassembling components of the gear motor and control valve for a hydraulic generator system on a wheeled excavator model. It describes 12 steps to disassemble the control valve, involving removing springs, seals, plugs and other parts. Separate sections provide installation and removal procedures for the gear motor and control valve.
The document provides instructions for assembling and disassembling components of the gear motor and control valve for a hydraulic generator system on a wheeled excavator model. It describes 12 steps to disassemble the control valve, involving removing springs, seals, plugs and other parts. Separate sections provide installation and removal procedures for the gear motor and control valve.
1) The document provides assembly and disassembly instructions for a control valve and gear motor used in a wheeled excavator.
2) It describes removing and installing various components like seals, springs, plugs, and housings. Torque specifications are provided for fasteners.
3) Technicians are warned to release hydraulic pressure before working and to wear protective equipment when handling spring loaded parts to avoid injury.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fhjsjkdmemm
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and valves. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing matching components. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fjjsjefkskemm
This document provides instructions for disassembling the front final drive carriers, hubs, and brakes of a M313C Wheeled Excavator. The summary is:
1. Drain the oil and remove the front tires, carrier housing, planetary gears, retaining rings, thrust washers, bearings, ring gear housing, piston, clutch discs, carrier gear, seals, bearing cones, flange, spacer, and other components.
2. Tools including retaining ring pliers, pullers, spanners, pry bars, three jaw pullers, and drivers are required to remove these parts while taking precautions for springs and contained fluids.
3. The carrier housing, flange,
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...udfjjdjkskkemmd
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and poppets. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing components like carriers, hubs and brakes. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fjsekdemmd
This document provides instructions for disassembling the front final drive carriers, hubs, and brakes of a M313C Wheeled Excavator. The summary is:
1. Drain the oil and remove the front tires, carrier housing, planetary gears, retaining rings, and other components to disassemble the carrier housing.
2. Remove the ring gear housing components like bolts, springs, pistons and seals.
3. Disassemble the clutch discs, carrier gear, bearings, seals and other remaining components to fully disassemble the front final drive, carriers, hubs and brakes.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fjjskekdmem
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and poppets. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing components like carriers, hubs and brakes. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fhjsjejfjskekemm
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and poppets. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing components like carriers, hubs and brakes. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fujsjjfeskekmm
This document provides instructions for disassembling the front final drive carriers, hubs, and brakes of a M313C Wheeled Excavator. The summary is:
1. Drain the oil and remove the front tires, carrier housing, planetary gears, retaining rings, and other components to disassemble the carrier housing.
2. Remove the ring gear housing components like bolts, springs, pistons and seals.
3. Disassemble the clutch discs, carrier gear, bearings, seals and other remaining components to fully disassemble the front final drive, carriers, hubs and brakes.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
This document provides instructions for removing and installing various components of the crankshaft and flywheel housing on a 325C Excavator. It describes how to remove and install the flywheel, crankshaft rear seal, rear seal carrier, and flywheel housing. The procedures include lists of required tools and step-by-step instructions describing how to remove each component and install the replacement parts. Safety notices are provided to keep parts clean and contain fluids appropriately during the repair work.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
More Related Content
Similar to Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001 and up).pdf
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fjjsjefkskemm
This document provides instructions for disassembling the front final drive carriers, hubs, and brakes of a M313C Wheeled Excavator. The summary is:
1. Drain the oil and remove the front tires, carrier housing, planetary gears, retaining rings, thrust washers, bearings, ring gear housing, piston, clutch discs, carrier gear, seals, bearing cones, flange, spacer, and other components.
2. Tools including retaining ring pliers, pullers, spanners, pry bars, three jaw pullers, and drivers are required to remove these parts while taking precautions for springs and contained fluids.
3. The carrier housing, flange,
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...udfjjdjkskkemmd
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and poppets. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing components like carriers, hubs and brakes. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fjsekdemmd
This document provides instructions for disassembling the front final drive carriers, hubs, and brakes of a M313C Wheeled Excavator. The summary is:
1. Drain the oil and remove the front tires, carrier housing, planetary gears, retaining rings, and other components to disassemble the carrier housing.
2. Remove the ring gear housing components like bolts, springs, pistons and seals.
3. Disassemble the clutch discs, carrier gear, bearings, seals and other remaining components to fully disassemble the front final drive, carriers, hubs and brakes.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fjjskekdmem
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and poppets. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing components like carriers, hubs and brakes. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fhjsjejfjskekemm
This document provides instructions for disassembling the travel brake valve and final drive carriers, hubs, and brakes on the front and rear axles of a M313C Wheeled Excavator. The travel brake valve disassembly involves 19 steps that remove components like pistons, springs, plugs and poppets. The front axle final drive disassembly involves 22 steps that remove components like planetary gears, retaining rings, bearings and seals. The rear axle final drive disassembly uses similar tools and involves removing components like carriers, hubs and brakes. Cleanliness is important during disassembly and assembly to prevent contamination of hydraulic systems.
Caterpillar cat m313 c wheeled excavator (prefix h2a) service repair manual (...fujsjjfeskekmm
This document provides instructions for disassembling the front final drive carriers, hubs, and brakes of a M313C Wheeled Excavator. The summary is:
1. Drain the oil and remove the front tires, carrier housing, planetary gears, retaining rings, and other components to disassemble the carrier housing.
2. Remove the ring gear housing components like bolts, springs, pistons and seals.
3. Disassemble the clutch discs, carrier gear, bearings, seals and other remaining components to fully disassemble the front final drive, carriers, hubs and brakes.
Similar to Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001 and up).pdf (6)
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
This document provides instructions for removing and installing various components of the crankshaft and flywheel housing on a 325C Excavator. It describes how to remove and install the flywheel, crankshaft rear seal, rear seal carrier, and flywheel housing. The procedures include lists of required tools and step-by-step instructions describing how to remove each component and install the replacement parts. Safety notices are provided to keep parts clean and contain fluids appropriately during the repair work.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...jdkskmdmdm
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jdkskmdmdm
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, installing new gaskets, and tightening bolts in a specific sequence using torque wrenches and degree wheels to ensure proper torque.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...jdkskmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415453
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01207418
1. Use a suitable lifting device to install piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
2. Install bolts (6).
1/2(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 2 g01207416
3. Use a suitable lifting device to reposition fan motor assembly (4), as shown. The weight of
fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207415
4. Install hub (3) and bolts (2).
5. Bend locking tabs (1) over bolts (2).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 16:59:41 UTC+0800 2020
2/2(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02554917
Hydraulic Lockout Control - Remove
SMCS - 5001-011-LK
Removal Procedure
Illustration 1 g01187398
1. Remove screws (2) and panel (1).
1/2(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 2 g01278781
2. Remove screws (6). Cut cable strap (8) and place switch (7) aside.
3. Remove bolt (4), bolt (5), and hydraulic lockout control (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 17:00:37 UTC+0800 2020
2/2(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378526
Hydraulic Lockout Control - Disassemble
SMCS - 5001-015-LK
Disassembly Procedure
Start By:
a. Remove the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Remove".
Illustration 1 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/3(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove retaining rings (1) and lever assembly (2).
2. Remove retaining ring (4), lever assembly (5), and spring (3).
Illustration 2 g01187383
3. Pull back cover (8) in order to remove pin (7) from pipe assembly (6).
Illustration 3 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 4. Remove pin (10) from pin (9).
5. Remove spring (11) from cover (12).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 17:01:35 UTC+0800 2020
3/3(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378527
Hydraulic Lockout Control - Assemble
SMCS - 5001-016-LK
Assembly Procedure
Illustration 1 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 1. Install spring (11) to cover (12).
2. Install pin (10) to pin (9).
Illustration 2 g01187383
3. Install pin (7) to pipe assembly (6).
4. Slide cover (8) over pipe assembly (6).
Illustration 3 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Install spring (3), lever assembly (5), and retaining ring (4).
2/3(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 6. Install lever assembly (2) and retaining rings (1).
End By:
a. Install the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 17:02:31 UTC+0800 2020
3/3(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07426591
Hydraulic Lockout Control - Install
SMCS - 5001-012-LK
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 243 -
Illustration 1 g01278781
1. Install hydraulic lockout control (3), bolt (4), and bolt (5).
2. Apply Tooling (A) to the threads of screws (6). Position switch assembly (7) and install
screws (6). Tighten screws (6) to a torque of 0.7 ± 0.1 N·m (6.2 ± 0.9 lb in). Attach cable
strap (8).
1/2(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g01187398
3. Install panel (1) and screws (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 17:03:27 UTC+0800 2020
2/2(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR B6H
Configuration: 330D L Excavators B6H00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02417256
Operator Console - Remove and Install
SMCS - 5258-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Start By:
a. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove".
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/9(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g01208165
1. Remove plates (1) and (2).
Illustration 2 g01196137
2. Attach Tooling (A) and an air supply to the hydraulic oil tank. Apply 345 ± 70 kPa
(50 ± 10 psi) to Tooling (A).
2/9(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 6. Disconnect harness assemblies (6).
Illustration 7 g01208204
7. Remove plate (8). Move floor mat (7) toward the front of the cab.
Illustration 8 g01208208
8. Remove bolts (9) from each side of the operator console. Pull hose assemblies (3) and (4)
through the floor of the cab. Hose assemblies (3) and (4) were removed in Steps 3 and 4.
Pull harness assemblies (5) and (6) through the floor of the cab. Harness assemblies (5) and
(6) were removed in Steps 5 and 6.
Note: If the machine is equipped with a radio, the antenna will need to be disconnected.
4/9(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 9 g01208250
9. Disconnect harness assembly (10).
Illustration 10 g01208252
10. Remove bolts (11) and operator console (12).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Illustration 11 g01208252
1. Install operator console (12) and bolts (11).
5/9(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 12 g01208250
2. Connect harness assembly (10).
Illustration 13 g01208208
3. Insert hose assemblies (3) and (4) through the hole in the cab floor. Insert harness
assemblies (5) and (6) through the holes in the cab floor. Hose assemblies (3) and (4) and
harness assemblies (5) and (6) will be connected in the following steps. Install bolts (9)
from each side of the operator console.
Note: If the machine is equipped with a radio, the antenna will need to be connected.
Illustration 14 g01208204
6/9(W)
w
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...