This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It lists the required tools and presents the steps to:
1. Remove the travel motor head and internal components like springs, seals, and plates.
2. Disassemble further to remove the brake piston, rotating assembly, and bearings.
3. Clean and inspect all parts before reassembly in reverse order. Precise alignment of parts is important for proper function.
JOHN DEERE 430 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 332 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians performing maintenance and repairs. Safety messages throughout warn of hazards involving high pressure fluids, battery explosions, fire risks, and preventing acid burns or injuries.
JOHN DEERE 330 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 322 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
John Deere 261 and 272 Rear-Mounted Mowers Service Repair Manual Instant Down...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 74 and 84 Blades Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D, 62D AND 72D OnRamp Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D and 72 Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
JOHN DEERE 430 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 332 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians performing maintenance and repairs. Safety messages throughout warn of hazards involving high pressure fluids, battery explosions, fire risks, and preventing acid burns or injuries.
JOHN DEERE 330 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 322 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
John Deere 261 and 272 Rear-Mounted Mowers Service Repair Manual Instant Down...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 74 and 84 Blades Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D, 62D AND 72D OnRamp Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D and 72 Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 47 and 59 Snowbowers Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 31B Post Hole Digger Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 26 and 51-Inch Brooms Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 5E 2BV Blower Service Repair Manual Instant Download (TM1430).pdfjiuliu14811471
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreaching or pointing tools at people, and always shut off engines before adjusting or refueling.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document is a service manual that provides instructions for removing and installing the high-low transmission on a D8L track-type tractor. It details over 50 steps to disassemble the transmission down to individual components and then reassemble. These include draining fluids, removing mounting hardware, disconnecting wiring and hoses, using specialty tools to separate interconnected pieces, cleaning and inspecting parts, and precisely reinstalling components in the reverse order.
The document provides instructions for removing and installing the bulldozer blade on a D6R Track-Type Tractor. The key steps include:
1. Disconnecting hydraulic hoses from the manifold and capping the connections.
2. Removing bolts, caps, and shims from the lift cylinders and stabilizer link.
3. Installing tooling under the push arms and using it to support the bulldozer blade.
4. Removing mounting bolts to detach the bulldozer blade from the tractor frame.
Caterpillar Cat D4HTSK III TRACK SKIDDER (Prefix 7PK) Service Repair Manual I...jiuliu14811471
This document provides instructions for removing and installing the cylinder head assembly on a Caterpillar 3304 engine. The steps include draining coolant, removing exhaust manifolds, valve covers, belts, hoses, wires and other components. The cylinder head bolts are then removed to lift off the head. Reinstallation follows the reverse order, applying thread lubricant and torquing bolts to the specified values. Valve clearance is adjusted at the end.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a 3054E industrial engine. It includes removal and installation procedures with required tools and safety notices. The procedures describe removing/installing the exhaust manifold gasket, setscrews, and turbocharger. For valves, it describes removing/installing the valve springs, retainers, keepers, and stem seals while ensuring the piston is at top dead center.
This document provides installation instructions for a fuel injection pump on a 3054C industrial engine. It consists of 14 steps: 1) Ensure the engine is at top dead center, 2) Install an O-ring on the pump, 3) Position and bolt the pump to the housing, 4) Install a bracket, 5) Install the pump gear and tighten, 6) Connect wiring, 7) Connect fuel lines, 8) Adjust a spacer and bolt, 9) Tighten the gear nut, 10) Remove timing tools, 11) Install covers and pulleys, 12) Install fuel lines. The instructions include illustrations and torque specifications for each step.
1. The document provides instructions for assembling and disassembling the piston pump on a 994H Wheel Loader. It describes the required tools and gives step-by-step instructions with accompanying illustrations.
2. The assembly procedure involves installing bearings, seals, springs, pistons, and other components in the proper order. Precise measurements are taken to ensure correct lift-off limitations.
3. The disassembly and installation procedures are described for removing and installing the high pressure screen and piston pump. Hoses and fittings are disconnected and reconnected.
1. The document provides instructions for removing and installing the front drive housing and vibration damper of a Caterpillar 3516 engine.
2. To remove the front drive housing, various components must first be removed, including the oil filter base, crankshaft seal, accessory drive, oil and water pump drive, and auxiliary water pump. Tools and lifting devices are then used to remove the housing itself.
3. To remove the vibration damper, the pulley, hub, and mounting bolts must be detached. Guide bolts and lifting devices help slide off the damper parts. Proper lubrication and torque are required for reinstallation.
This document provides instructions for removing the engine oil pump from a Caterpillar 994D wheel loader. It describes draining the coolant, disconnecting electrical connections, and removing mounting bolts and brackets. The final step is to use lifting tools to remove the oil pump assembly, which weighs approximately 45 kg.
The document provides instructions for servicing components of a 994 wheel loader, including:
- Removing and installing the supplemental steer pump, which involves removing hydraulic lines and bolts then reversing the steps to install.
- Disassembling and assembling the supplemental steer pump, which involves removing seals, plates, gears, and reversing the steps to assemble.
- Removing and installing the steering control valve, which involves disconnecting hydraulic lines and removing mounting bolts then reversing the steps to install.
- Disassembling and assembling the steering control valve, which involves removing plugs, springs, valves, and reversing the steps to assemble.
- Removing and installing the steering neutralizer valve, which
This document provides instructions for servicing components of a Caterpillar 973C track loader powered by a C9 engine, including:
- Removing and installing the turbocharger, involving disconnecting hoses and removing nuts and bolts.
- Removing and installing the exhaust manifold, which is assembled from three pieces, requiring removal of nuts and installation of new gaskets and nuts.
- Removing and installing the air inlet heater by disconnecting electrical connections and ground strap and removing bolts to detach the air inlet elbow.
This document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and electrical connections, removing mounting bolts, and lifting the tank out of the machine. The installation process is described in reverse order. Proper safety procedures and maintenance tips are provided throughout.
1. The document provides instructions for disassembling and assembling various components of a 966K wheel loader, including the piston pump for steering, secondary steering pump and electric motor, secondary steering valve, and gear pump for secondary steering.
2. The procedures include removing and installing parts in a specified order, with illustrations showing each step. Safety precautions are provided for parts under spring tension.
3. Tools and torque specifications are listed for properly assembling components such as bolts, seals, and bearings. End play and alignment is checked using gauges or indicators.
1) The document provides assembly and disassembly instructions for a limited slip differential in a 966K wheel loader. It details cleaning and inspecting parts, installing various components like thrust washers, friction discs, and gears in the correct order, and measuring end play gaps to specifications.
2) Dismantling instructions include marking case halves, removing mounting bolts, and taking out internal components like side gears, springs, and clutch assemblies.
3) Safety notices warn of potential injury from parts under spring force and recommend following procedures while wearing protective equipment.
The document provides instructions for removing and installing various components on a Caterpillar 963K track loader, including:
1) Releasing hydraulic pressure before removing any lines or components.
2) Removing the ripper by detaching lift cylinders, loosening mounting bolts, and lifting it free with a hoist.
3) Removing the ripper lift cylinder by disconnecting lines and hoses, loosening mounting bolts, and lifting it out.
4) Removing the bucket by lowering the lift arm, releasing pressure, removing mounting pins, and lifting the bucket free with a hoist.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 47 and 59 Snowbowers Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 31B Post Hole Digger Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 26 and 51-Inch Brooms Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 5E 2BV Blower Service Repair Manual Instant Download (TM1430).pdfjiuliu14811471
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreaching or pointing tools at people, and always shut off engines before adjusting or refueling.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document is a service manual that provides instructions for removing and installing the high-low transmission on a D8L track-type tractor. It details over 50 steps to disassemble the transmission down to individual components and then reassemble. These include draining fluids, removing mounting hardware, disconnecting wiring and hoses, using specialty tools to separate interconnected pieces, cleaning and inspecting parts, and precisely reinstalling components in the reverse order.
The document provides instructions for removing and installing the bulldozer blade on a D6R Track-Type Tractor. The key steps include:
1. Disconnecting hydraulic hoses from the manifold and capping the connections.
2. Removing bolts, caps, and shims from the lift cylinders and stabilizer link.
3. Installing tooling under the push arms and using it to support the bulldozer blade.
4. Removing mounting bolts to detach the bulldozer blade from the tractor frame.
Caterpillar Cat D4HTSK III TRACK SKIDDER (Prefix 7PK) Service Repair Manual I...jiuliu14811471
This document provides instructions for removing and installing the cylinder head assembly on a Caterpillar 3304 engine. The steps include draining coolant, removing exhaust manifolds, valve covers, belts, hoses, wires and other components. The cylinder head bolts are then removed to lift off the head. Reinstallation follows the reverse order, applying thread lubricant and torquing bolts to the specified values. Valve clearance is adjusted at the end.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a 3054E industrial engine. It includes removal and installation procedures with required tools and safety notices. The procedures describe removing/installing the exhaust manifold gasket, setscrews, and turbocharger. For valves, it describes removing/installing the valve springs, retainers, keepers, and stem seals while ensuring the piston is at top dead center.
This document provides installation instructions for a fuel injection pump on a 3054C industrial engine. It consists of 14 steps: 1) Ensure the engine is at top dead center, 2) Install an O-ring on the pump, 3) Position and bolt the pump to the housing, 4) Install a bracket, 5) Install the pump gear and tighten, 6) Connect wiring, 7) Connect fuel lines, 8) Adjust a spacer and bolt, 9) Tighten the gear nut, 10) Remove timing tools, 11) Install covers and pulleys, 12) Install fuel lines. The instructions include illustrations and torque specifications for each step.
1. The document provides instructions for assembling and disassembling the piston pump on a 994H Wheel Loader. It describes the required tools and gives step-by-step instructions with accompanying illustrations.
2. The assembly procedure involves installing bearings, seals, springs, pistons, and other components in the proper order. Precise measurements are taken to ensure correct lift-off limitations.
3. The disassembly and installation procedures are described for removing and installing the high pressure screen and piston pump. Hoses and fittings are disconnected and reconnected.
1. The document provides instructions for removing and installing the front drive housing and vibration damper of a Caterpillar 3516 engine.
2. To remove the front drive housing, various components must first be removed, including the oil filter base, crankshaft seal, accessory drive, oil and water pump drive, and auxiliary water pump. Tools and lifting devices are then used to remove the housing itself.
3. To remove the vibration damper, the pulley, hub, and mounting bolts must be detached. Guide bolts and lifting devices help slide off the damper parts. Proper lubrication and torque are required for reinstallation.
This document provides instructions for removing the engine oil pump from a Caterpillar 994D wheel loader. It describes draining the coolant, disconnecting electrical connections, and removing mounting bolts and brackets. The final step is to use lifting tools to remove the oil pump assembly, which weighs approximately 45 kg.
The document provides instructions for servicing components of a 994 wheel loader, including:
- Removing and installing the supplemental steer pump, which involves removing hydraulic lines and bolts then reversing the steps to install.
- Disassembling and assembling the supplemental steer pump, which involves removing seals, plates, gears, and reversing the steps to assemble.
- Removing and installing the steering control valve, which involves disconnecting hydraulic lines and removing mounting bolts then reversing the steps to install.
- Disassembling and assembling the steering control valve, which involves removing plugs, springs, valves, and reversing the steps to assemble.
- Removing and installing the steering neutralizer valve, which
This document provides instructions for servicing components of a Caterpillar 973C track loader powered by a C9 engine, including:
- Removing and installing the turbocharger, involving disconnecting hoses and removing nuts and bolts.
- Removing and installing the exhaust manifold, which is assembled from three pieces, requiring removal of nuts and installation of new gaskets and nuts.
- Removing and installing the air inlet heater by disconnecting electrical connections and ground strap and removing bolts to detach the air inlet elbow.
This document provides instructions for removing and installing the hydrostatic drive oil tank on a Caterpillar 973C track loader. It describes draining the tank, disconnecting hoses and electrical connections, removing mounting bolts, and lifting the tank out of the machine. The installation process is described in reverse order. Proper safety procedures and maintenance tips are provided throughout.
1. The document provides instructions for disassembling and assembling various components of a 966K wheel loader, including the piston pump for steering, secondary steering pump and electric motor, secondary steering valve, and gear pump for secondary steering.
2. The procedures include removing and installing parts in a specified order, with illustrations showing each step. Safety precautions are provided for parts under spring tension.
3. Tools and torque specifications are listed for properly assembling components such as bolts, seals, and bearings. End play and alignment is checked using gauges or indicators.
1) The document provides assembly and disassembly instructions for a limited slip differential in a 966K wheel loader. It details cleaning and inspecting parts, installing various components like thrust washers, friction discs, and gears in the correct order, and measuring end play gaps to specifications.
2) Dismantling instructions include marking case halves, removing mounting bolts, and taking out internal components like side gears, springs, and clutch assemblies.
3) Safety notices warn of potential injury from parts under spring force and recommend following procedures while wearing protective equipment.
The document provides instructions for removing and installing various components on a Caterpillar 963K track loader, including:
1) Releasing hydraulic pressure before removing any lines or components.
2) Removing the ripper by detaching lift cylinders, loosening mounting bolts, and lifting it free with a hoist.
3) Removing the ripper lift cylinder by disconnecting lines and hoses, loosening mounting bolts, and lifting it out.
4) Removing the bucket by lowering the lift arm, releasing pressure, removing mounting pins, and lifting the bucket free with a hoist.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JCD
Configuration: 330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 15:44:36 UTC+0800 2020
11/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JCD
Configuration: 330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
5/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 15 g00887501
Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
10/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 15:45:39 UTC+0800 2020
11/11(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JCD
Configuration: 330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02372696
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 1 g00878123
2. Install new O-ring seal (5) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Fasten a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/3(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. 4. Carefully install travel motor (4) on Tooling (A) . Slide the travel motor into the final drive.
5. Install one of three bolts (5) that secures the travel motor to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
7. Install two remaining bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Final Drive Oil Level - Check"
for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 15:46:42 UTC+0800 2020
3/3(W)
w
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...