This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...hfjsekekmmd
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...hfjsekekmmd
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with bolts finger tight.
4. Aligning the front cover with an alignment tool and tightening the bolts to specification. Installing a new front seal completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket and front cover with guide studs, and tightening bolts with an alignment tool installed.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fdjsuekskefmm
The document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator including the crankshaft front seal, vibration damper and pulley, and front cover. The procedures include using various tools to remove and install each part and applying Loctite to the crankshaft front seal. Torques are provided for tightening bolts and screws.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fjjskkdmnsme
1. The document provides instructions for removing and installing a front cover on a Caterpillar C6.6 engine.
2. The removal procedure involves removing bolts and identifying bolts of different lengths, then removing the front cover and gasket.
3. The installation procedure specifies cleaning surfaces, installing a new gasket, using guide studs to position the cover, and torquing bolts to the specified value.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fujdfjjkskekme
1) The document provides instructions for removing and installing a front cover on a Caterpillar C6.6 engine.
2) It describes using various tools to remove bolts and separate the front cover from the front housing. The front seal and gasket must also be removed.
3) Cleaning surfaces and installing a new gasket and seal are covered. Alignment tools are used to correctly position the new front cover assembly before tightening bolts.
This document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator engine, including:
1. Removing and installing the crankshaft front seal using various specialized tools.
2. Instructions for removing and installing the front cover, vibration damper, pulley, and front seal.
3. Detailed steps and illustrations are provided for each procedure, and required tools are listed. Precautions are noted to keep parts clean and lubricated as needed.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine safely and correctly. Safety notices are provided regarding keeping parts clean and not lubricating certain components.
This document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator engine, including:
1) Removing and installing the crankshaft front seal using various specialized tools.
2) Instructions for removing and installing the front cover, which houses the crankshaft front seal. Removal requires removing mounting bolts and identifying bolts of different lengths.
3) Procedures for installing the vibration damper and pulley on the crankshaft, which requires aligning parts using guide studs and torqueing bolts to specified values.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with bolts finger tight.
4. Aligning the front cover with an alignment tool and tightening the bolts to specification. Installing a new front seal completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket and front cover with guide studs, and tightening bolts with an alignment tool installed.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a front cover on a Caterpillar 330F excavator engine. Key steps include:
1. Removing the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Removing bolts from the front cover and housing, and removing the front cover and gasket.
3. Cleaning the front cover and housing, installing a new gasket with guide studs, and installing the front cover with alignment tools. Reinstalling the front seal, pulley, and fan completes the process.
The document provides instructions for removing and installing a crankshaft front seal and front cover on a Caterpillar 330F excavator engine. The removal process involves using specialty tools to screw the front seal out of the front cover. For installation, a new seal is lubricated and installed using an installer tool. Instructions also cover removing and installing the front cover, which requires identifying bolt lengths and using guide studs and an alignment tool.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fdjsuekskefmm
The document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator including the crankshaft front seal, vibration damper and pulley, and front cover. The procedures include using various tools to remove and install each part and applying Loctite to the crankshaft front seal. Torques are provided for tightening bolts and screws.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fjjskkdmnsme
1. The document provides instructions for removing and installing a front cover on a Caterpillar C6.6 engine.
2. The removal procedure involves removing bolts and identifying bolts of different lengths, then removing the front cover and gasket.
3. The installation procedure specifies cleaning surfaces, installing a new gasket, using guide studs to position the cover, and torquing bolts to the specified value.
Caterpillar cat 320 e lrr excavator (prefix pnl) service repair manual (pnl00...fujdfjjkskekme
1) The document provides instructions for removing and installing a front cover on a Caterpillar C6.6 engine.
2) It describes using various tools to remove bolts and separate the front cover from the front housing. The front seal and gasket must also be removed.
3) Cleaning surfaces and installing a new gasket and seal are covered. Alignment tools are used to correctly position the new front cover assembly before tightening bolts.
This document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator engine, including:
1. Removing and installing the crankshaft front seal using various specialized tools.
2. Instructions for removing and installing the front cover, vibration damper, pulley, and front seal.
3. Detailed steps and illustrations are provided for each procedure, and required tools are listed. Precautions are noted to keep parts clean and lubricated as needed.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine safely and correctly. Safety notices are provided regarding keeping parts clean and not lubricating certain components.
This document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator engine, including:
1) Removing and installing the crankshaft front seal using various specialized tools.
2) Instructions for removing and installing the front cover, which houses the crankshaft front seal. Removal requires removing mounting bolts and identifying bolts of different lengths.
3) Procedures for installing the vibration damper and pulley on the crankshaft, which requires aligning parts using guide studs and torqueing bolts to specified values.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine's crankshaft pulley, vibration damper, front seal, and front cover. Precautions are provided to keep parts clean and torque specifications are given.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine safely and correctly. Precautions are provided to keep parts clean and prevent damage. Required tools are listed for each procedure.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal on the front cover.
The document provides detailed step-by-step instructions and illustrations for performing maintenance on the engine safely and correctly. Safety notices are included to keep parts clean and prevent damage.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for completing each task while maintaining cleanliness and using the correct tools and torque specifications.
This document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator engine, including:
1) Removing and installing the crankshaft front seal using various specialized tools.
2) Instructions for removing and installing the front cover, removing bolts of different lengths and replacing the gasket.
3) Detailed steps for installing the vibration damper and pulley on the crankshaft, including cleaning, inspection of parts, and tightening bolts to specified torques.
This document provides instructions for removing and installing various components of a Caterpillar 320E LRR excavator engine, including:
1. Removing and installing the crankshaft front seal using various specialized tools.
2. Instructions for removing and installing the front cover, vibration damper, pulley, and front seal.
3. Detailed steps and illustrations are provided for each procedure, and required tools are listed. Precautions are noted to keep parts clean and lubricated as needed.
Similar to Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 and up) (18)
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper order. It also provides disassembly instructions for a final drive in 13 steps, removing components like bolts, gears, and covers. Installation requires cleaning, applying sealant, and torquing bolts to specified values.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It describes 27 steps to disassemble the motor by removing components like the motor head, springs, brake piston, rotating assembly, bearings and seals. It then describes 28 steps for reassembling the motor components in reverse order, making sure to align parts properly, apply lubricants to seals and mating surfaces, and torque bolts to the specified values. The proper procedure is important to safely release spring forces and prevent damage during removal and installation of parts.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring forces or pressurized components.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...fhsjekdmme
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix fbt) service repair manual (fbt000...fhsjekdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar cat 336 d2 l excavator (prefix faj) service repair manual (faj000...fhsjekdmme
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pullers, pry bars, and seal removal tools.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR HBT
Configuration: 330F & 330F LN Excavators HBT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909517
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.f in order to install vibration damper, crankshaft
pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Remove Tooling (D) .
f. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Sun Jun 28 12:02:17 UTC+0800 2020
3/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR HBT
Configuration: 330F & 330F LN Excavators HBT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018646
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly 1
2/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03417117
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 12:03:13 UTC+0800 2020
4/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR HBT
Configuration: 330F & 330F LN Excavators HBT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i06799526
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & Installer Tool 1
B 207-1601 P-80 Rubber Lubricant 1
Start By:
a. Remove the crankshaft vibration damper and pulley.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 1 g03417118
1. Position Tooling (A) onto crankshaft front seal (2).
2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1).
Installation Procedure
1. Ensure that the front cover is clean and free from damage.
2/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 3 g03453516
2. Apply Tooling (B) to static twin dead seal (3) (not shown) to a new crankshaft front seal (2).
Ensure that none of Tooling (B) contaminates the crankshaft front seal in Position (Y).
3. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1).
4. Position Tooling (A) onto crankshaft front seal (2).
5. Use Tooling (A) to turn crankshaft front seal (2) in a clockwise direction.
6. If a torque that is greater than 50 N·m (37 lb ft) is necessary to install crankshaft front seal
(2), remove crankshaft front seal (2). Inspect crankshaft front seal (2) and front cover (1) for
faults or damage.
7. If necessary, repeat Step 2 through Step 6 to install crankshaft front seal (2).
End By:
a. Install the crankshaft vibration damper and pulley.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 12:04:09 UTC+0800 2020
4/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR HBT
Configuration: 330F & 330F LN Excavators HBT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018648
Front Cover - Remove and Install - Heavy Duty Front Cover
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
b. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
c. Remove the front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal -
Remove and Install" for the correct procedure.
1/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g02048613
1. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
2. Remove front cover (1) from the front housing.
3. Remove gasket (2) from front cover (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Studs
M8 by 70 mm
2
B 364-7210 Front Cover Alignment Tool 1
2/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 2 g02190213
1. Ensure that all components are clean and free from damage. Replace any damaged
components.
2. Thoroughly clean the gasket surface of the front housing.
3. Thoroughly clean front cover (1).
4. Install Tooling (A) into Holes (X) in the front housing.
5. Install a new gasket (2) onto Tooling (A).
6. Install front cover (1) onto Tooling (A).
7. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
8. Use Tooling (B) to align the front cover assembly.
3/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 9. Remove Tooling (A) and install remaining bolts (4).
10. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
11. Remove Tooling (B).
12. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
b. If the engine was equipped with a fan, install the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 12:05:04 UTC+0800 2020
4/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR HBT
Configuration: 330F & 330F LN Excavators HBT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i07167344
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
b. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
1/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 1 g01992013
1. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
2. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
3. Remove front cover (1) from the front housing.
4. Remove gasket (2) from front cover (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 70 mm
2
B 367-3535 Front Cover Alignment Tool 1
2/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g02190133
1. Thoroughly clean the gasket surface of the front housing.
2. If the original front cover is installed, follow Step 2.a through Step 2.b.
a. Thoroughly clean front cover (1).
b. Install a new gasket (2) to front cover (1). Engage Locators (Y) into the holes in the
front cover.
3. Install Tooling (A) into Holes (X) in the front housing.
4. Use Tooling (A) to position the front cover assembly onto the front housing.
5. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
3/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 6. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
7. Use Tooling (B) to align the front cover.
8. Remove Tooling (A) and install remaining bolts (4).
9. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
10. Remove Tooling (B) from the front cover.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
b. If the engine was equipped with a fan, install the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 28 12:06:00 UTC+0800 2020
4/4(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR HBT
Configuration: 330F & 330F LN Excavators HBT00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018649
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Fuel Injection Pump Timing Pin 1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
1/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. Care must be taken in
order to ensure that the fuel injection pump timing is not lost during the removal of the front gear
group. Carefully follow the procedure in order to remove the gear group.
2/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 1 g01992076
1. Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
3. Install Tooling (D) through Hole (W) in order to lock the crankshaft.
4. Remove Tooling (D).
5. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at 60 degrees after top dead center.
Illustration 2 g03453525
6. Use Tooling (E) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew
threaded inserts (4) on all rocker arms (3) until all valves are fully closed.
Note: Ensure that ALL threaded inserts are fully unscrewed.
7. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
8. Install Tooling (D) through Hole (W) in order to lock the crankshaft. Refer to Illustration 1.
3/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 3 g03453527
9. Install Tooling (B) through Hole (X) in camshaft gear (5) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
10. Install Tooling (D) into Hole (W) in the cylinder block. Use Tooling (D) in order to lock the
crankshaft in the correct position. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
11. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
4/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 4 g03453528
12. Mark gear (5), gear (6), gear (7), and gear (8) in order to show alignment. Refer to
Illustration 4.
Note: Identification will ensure that the gears can be installed in the original alignment.
13. Remove Tooling (B), Tooling (C), and Tooling (D).
14. Remove camshaft gear (5). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
15. Remove idler gear (6). Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Fuel Injection Pump Timing Pin 1
D 136-4632 Timing Pin (Crankshaft) 1
5/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F
7H-1942 Dial Indicator 1
- Magnetic Base and Stand 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston" for the
correct procedure.
Illustration 5 g02085993
6/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 2. If necessary, install Tooling (D) into Hole (W) in the cylinder block. Use Tooling (D) in
order to lock the crankshaft in the correct position. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
3. Ensure that all of the components of the front gear group are clean and free from wear and
damage. If necessary, replace any components that are worn or damaged.
Illustration 6 g03453530
4. Install camshaft gear (5). Loosely install bolt (10) and washer (9) for the camshaft gear.
Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for the correct
procedure.
7/14(W)
w
2020/6/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...