The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly and inspecting O-rings and seals for wear. The assembly process involves installing seals and O-rings into the outside housing, positioning the rotor inside the housing, and attaching the housing to the rotor with bolts and washers. Proper cleanliness is emphasized throughout the assembly.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjskemdme
The document provides instructions for assembling an excavator swivel joint. It describes cleaning the parts thoroughly before assembly. It details installing new seals and O-rings on the outside housing and rotor. The rotor and outside housing are joined using bolts and washers, and the assembly is then attached to the excavator with hoses and fittings. Proper cleaning and installation of seals are important to prevent contamination issues.
Caterpillar cat 336 d l excavator (prefix wet) service repair manual (wet0000...fjjskekdm
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists the required tools and gives step-by-step instructions to remove the component by draining fluids, disconnecting hoses, and removing bolts. Instructions are also provided to install the component by replacing seals, positioning the motor, and tightening bolts to the specified torque.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 336 d l excavator (prefix jwr) service repair manual (jwr0000...fjskemdme
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists the required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the final drive and travel motor assembly using lever pullers, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar cat 323 f ln excavator (prefix rgp) service repair manual (rgp000...fjjskekdmme
This document provides instructions for removing and installing electronic unit injectors on a C4.4 engine. The removal process involves draining fuel, removing fuel lines and electrical connections, and prying the injector from the cylinder head. Installation requires cleaning components, applying new seals and bolts, and calibrating the injector code in the electronic control module. Tools including sockets, pry bars, caps, and torque wrenches are required. Precautions are listed to contain fluids, ensure cleanliness, and only have authorized personnel perform fuel system work.
Caterpillar cat 336 d excavator (prefix m3m) service repair manual (m3m00001 ...fjskekdmjekm
This document provides installation instructions for installing a swivel on an excavator. It involves attaching lifting tools to the swivel, installing fittings and hoses, and securing the swivel in place with bolts while applying the proper torque. Cleanliness is important during installation to prevent contamination. The document also provides disassembly and assembly instructions for the swivel components.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 336 d l excavator (prefix j2f) service repair manual (j2f0000...fksjksmmde
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses and fittings, remove mounting bolts, and lift out the final drive assembly. Detailed steps are provided for removing the travel motor from the final drive as well as installing the components in reverse order. Safety notices remind technicians to contain fluids and avoid contamination during the process.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjskemdme
The document provides instructions for assembling an excavator swivel joint. It describes cleaning the parts thoroughly before assembly. It details installing new seals and O-rings on the outside housing and rotor. The rotor and outside housing are joined using bolts and washers, and the assembly is then attached to the excavator with hoses and fittings. Proper cleaning and installation of seals are important to prevent contamination issues.
Caterpillar cat 336 d l excavator (prefix wet) service repair manual (wet0000...fjjskekdm
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists the required tools and gives step-by-step instructions to remove the component by draining fluids, disconnecting hoses, and removing bolts. Instructions are also provided to install the component by replacing seals, positioning the motor, and tightening bolts to the specified torque.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 336 d l excavator (prefix jwr) service repair manual (jwr0000...fjskemdme
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists the required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the final drive and travel motor assembly using lever pullers, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar cat 323 f ln excavator (prefix rgp) service repair manual (rgp000...fjjskekdmme
This document provides instructions for removing and installing electronic unit injectors on a C4.4 engine. The removal process involves draining fuel, removing fuel lines and electrical connections, and prying the injector from the cylinder head. Installation requires cleaning components, applying new seals and bolts, and calibrating the injector code in the electronic control module. Tools including sockets, pry bars, caps, and torque wrenches are required. Precautions are listed to contain fluids, ensure cleanliness, and only have authorized personnel perform fuel system work.
Caterpillar cat 336 d excavator (prefix m3m) service repair manual (m3m00001 ...fjskekdmjekm
This document provides installation instructions for installing a swivel on an excavator. It involves attaching lifting tools to the swivel, installing fittings and hoses, and securing the swivel in place with bolts while applying the proper torque. Cleanliness is important during installation to prevent contamination. The document also provides disassembly and assembly instructions for the swivel components.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 336 d l excavator (prefix j2f) service repair manual (j2f0000...fksjksmmde
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses and fittings, remove mounting bolts, and lift out the final drive assembly. Detailed steps are provided for removing the travel motor from the final drive as well as installing the components in reverse order. Safety notices remind technicians to contain fluids and avoid contamination during the process.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 323 d l excavator (prefix nde) service repair manual (nde0000...fjjsekmsmmes
The document provides instructions for removing and installing a camshaft on a Caterpillar C6.4 engine. To remove the camshaft, first remove the valve lifters and then pull out the camshaft. To install the camshaft, lubricate the valve lifters, reinstall them in their original locations, and then insert the camshaft. Proper cleaning and lubrication of parts is important to prevent wear.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...uujjfjkkkdmme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the pump from the machine. Safety precautions are provided, such as ensuring all attachments are lowered and oil is cool before removal to avoid injury from hydraulic pressure. The piston pump weighs approximately 45 kg.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...shudun96087
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly to prevent damage. It instructs installing new O-rings and seals if worn. The steps include positioning the rotor and outside housing using lifting tools, applying the seals and O-rings, and securing with bolts, washers, and covers while torquing to the specified values. Proper cleaning and inspection of parts is emphasized to avoid contamination issues.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...kesi7153062
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly to prevent damage. It instructs installing new O-rings and seals if worn. The steps include positioning the rotor and outside housing using lifting tools, applying the seals and O-rings, and securing with bolts, washers, and covers while torquing to the specified values. Proper cleaning and inspection of parts is emphasized to avoid contamination issues.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...cnp692569
The document provides installation instructions for a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it.
2) Connecting hydraulic hoses and installing supporting components.
3) Installing fittings, hoses, covers and bolts to fully assemble the swivel.
4) Removing the vacuum tool after installation is complete.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjskkkdmem
The document provides installation instructions for a swivel on an excavator. It includes:
1) Attaching lifting devices and positioning the swivel assembly.
2) Installing hoses, fittings, and covers on the swivel.
3) Reinstalling the hydraulic tank cap and filling the hydraulic system.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjjsekwsxkdmmem
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...f8uesjdkdmdm
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...f8sejdkdmdijd
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to secure the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...ze3xiandiao
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the reverse order of disassembly. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...f7usuejkdkddm3
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to fill the hydraulic system.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...ufs89eodkdmdm
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...jdkskmmdmd1
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...jdkskmdmdm
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 323 d l excavator (prefix nde) service repair manual (nde0000...fjjsekmsmmes
The document provides instructions for removing and installing a camshaft on a Caterpillar C6.4 engine. To remove the camshaft, first remove the valve lifters and then pull out the camshaft. To install the camshaft, lubricate the valve lifters, reinstall them in their original locations, and then insert the camshaft. Proper cleaning and lubrication of parts is important to prevent wear.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...uujjfjkkkdmme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the pump from the machine. Safety precautions are provided, such as ensuring all attachments are lowered and oil is cool before removal to avoid injury from hydraulic pressure. The piston pump weighs approximately 45 kg.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...shudun96087
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly to prevent damage. It instructs installing new O-rings and seals if worn. The steps include positioning the rotor and outside housing using lifting tools, applying the seals and O-rings, and securing with bolts, washers, and covers while torquing to the specified values. Proper cleaning and inspection of parts is emphasized to avoid contamination issues.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...kesi7153062
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly to prevent damage. It instructs installing new O-rings and seals if worn. The steps include positioning the rotor and outside housing using lifting tools, applying the seals and O-rings, and securing with bolts, washers, and covers while torquing to the specified values. Proper cleaning and inspection of parts is emphasized to avoid contamination issues.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...cnp692569
The document provides installation instructions for a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it.
2) Connecting hydraulic hoses and installing supporting components.
3) Installing fittings, hoses, covers and bolts to fully assemble the swivel.
4) Removing the vacuum tool after installation is complete.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjskkkdmem
The document provides installation instructions for a swivel on an excavator. It includes:
1) Attaching lifting devices and positioning the swivel assembly.
2) Installing hoses, fittings, and covers on the swivel.
3) Reinstalling the hydraulic tank cap and filling the hydraulic system.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjjsekwsxkdmmem
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...f8uesjdkdmdm
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...f8sejdkdmdijd
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to secure the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...ze3xiandiao
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the reverse order of disassembly. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...f7usuejkdkddm3
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to fill the hydraulic system.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...ufs89eodkdmdm
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...jdkskmmdmd1
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...jdkskmdmdm
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...pwg56547003
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...jfdjskmdmme
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Separating the track and removing fasteners and hoses to access the assembly.
2. Attaching lifting tools and slowly removing the heavy assembly from the excavator.
3. Reversing the process to reinstall the assembly, replacing seals and fasteners, and refilling fluids. Proper torque and sequencing is required.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...cdfzxs
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to install the components in reverse order. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...fjjsekkksmeik
This document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. The removal process involves: releasing hydraulic pressure, separating the track, removing hoses and fittings, attaching lifting tools, and removing mounting bolts. The installation is the reverse of removal, and includes checking seals, applying anti-seize compound, reconnecting hoses, filling the hydraulic system, and reinstalling covers. A separate section provides instructions for removing the swivel assembly, which involves disconnecting hoses, attaching lifting tools, and removing retaining bolts.
Similar to Caterpillar cat 330 d l excavator (prefix has) service repair manual (has00001 and up) (20)
John deere 975 combines service repair manual (tm4387)fjjsekkksmeik
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
1996 polaris indy tran sport snowmobile service repair manualfjjsekkksmeik
This document provides publication numbers and service bulletin indexes for Polaris snowmobiles from 1994-1998. It lists the model, model number, owner's manual part number, parts manual part number, and other relevant documentation for each year. The section also indexes service bulletins by number and provides brief descriptions of the technical issues covered in each bulletin for 1994-1995 models.
This document provides instructions for renewing various components of the 2.9L Jaguar engine, including the auxiliary drive shaft, camshaft, crankshaft, cylinder head, oil pump, timing chains, and other parts. The renewal process involves removing worn parts and cleaning and inspecting components before fitting replacements and reassembling the engine. Special tools are required for some tasks like removing oil seals.
1989 polaris indy 500 sks snowmobile service repair manualfjjsekkksmeik
The document describes vehicle models and specifications for 1985-1995. It provides details on model identification numbers, engine types, dimensions, features and specifications for each model year. Model details are given for 1985 models including the Star, SS, Indy Trail, Indy 600, 600SE and LongTrack.
Yamaha outboard ft50 cet service repair manual l 450101 fjjsekkksmeik
The document is a service manual that provides general information and technical tips about an FT50C outboard motor. It includes:
1) An overview of the manual format and symbols used as well as safety procedures for working on the motor.
2) Details on the motor features such as its use of leaded gasoline, newly designed four carburetors, and CDI ignition unit.
3) Explanations of technical aspects like the carburetor operation including its starting, idle, medium and high speed functions.
Terex girolift 5022 perfora telescopic handler service repair manualfjjsekkksmeik
This document is a workshop manual that provides instructions for maintenance and repairs of a handler with a telescopic boom. It contains sections on general information, safety regulations, technical specifications, inspections, disassembly and assembly, troubleshooting, maintenance of specific components like the axle, engine, pumps, gearbox, and load limiter. The appendices provide information on tools, torque specifications, weights of parts, and refilling specifications. The manual is intended to allow safe and proper maintenance of the machine.
Perkins phaser 135 ti model al (euro 2) diesel engine service repair manualfjjsekkksmeik
This document provides a workshop manual for the Perkins Phaser 135 Ti 4 cylinder diesel engine. It contains specifications, instructions for disassembly and assembly of engine components, timing procedures, and safety information. The manual is divided into chapters covering the cylinder head, pistons and connecting rods, crankshaft, timing components, cylinder block, and other systems such as fuel, cooling, and aspiration.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...fjjsekkksmeik
The document provides instructions for disassembling the piston pump (swing) of an M315C wheeled excavator. It describes removing 22 individual parts from the pump housing including the servo valve, charge pump, gears, head, port plate, relief valves, spool, and adjustment screw. Cleanliness is important when disassembling to prevent dirt from entering the internal mechanisms. Personal injury precautions are also noted regarding hydraulic pressure and spring force.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjsekkksmeik
This document provides assembly and disassembly instructions for the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, pistons, seals and bearings. It notes to mark components' orientations. Reassembly follows the reverse of disassembly, noting to replace bolts and apply threadlock. Safety warnings caution of parts under spring pressure and ensuring fluid containment.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...fjjsekkksmeik
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...fjjsekkksmeik
The document provides instructions for disassembling a 330D2 excavator travel motor. The 27 step procedure includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, and other components. Special tools are required and technicians are warned to contain fluids, mark components for reassembly, and use care when handling springs or moving parts that could cause injury.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...fjjsekkksmeik
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...fjjsekkksmeik
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components given their significant weights ranging from 32 to 550 kilograms. Cleanliness is emphasized to prevent dirt entry during disassembly.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...fjjsekkksmeik
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure reverses this process and puts the travel motor back together in 25 steps, reinstalling the parts in the reverse order that they were removed. Precise instructions are given for each step to ensure correct reassembly.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...fjjsekkksmeik
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...fjjsekkksmeik
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07188136
Final Drive and Travel Motor - Install
SMCS - 4050-012; 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 439-3938 Link Bracket 1
D - Loctite C5A Copper Anti-Seize -
Note: Check the O-ring seals for wear or for damage. Replace the O-ring seals, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01181921
1. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
2. Position travel motor (11). Install bolts (12) that mount travel motor (11) to final drive (13).
2/5(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g01181917
3. Install O-ring seals (10) and (9).
Illustration 3 g01181914
4. Install counterbalance valve (8) and bolts (7).
Illustration 4 g01181911
3/5(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g01182266
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb).
6. Carefully position final drive and travel motor (5). Apply Tooling (D) to the threads of bolts
(6).
7. Tighten bolts (6) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
Illustration 6 g01223711
8. Install fitting (4). Connect hose assemblies (3).
4/5(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 7 g00944947
9. Remove Tooling (A). Install the cap onto the hydraulic tank.
10. Fill the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricant Viscosities
and Refill Capacities".
Illustration 8 g01223707
11. Install cover (2) and bolts (1). Tighten bolts (1) to a torque of 130 ± 10 N·m (96 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:00:12 UTC+0800 2020
5/5(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434256
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g01209599
1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216069
2. Disconnect hose assemblies (1), (2), and (3). Remove support (4).
Illustration 3 g01216082
2/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 3. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Remove bolts (6) and retainer (8). Remove clamp (7) and boot
(5).
Illustration 4 g01216099
4. Remove bolts (10) and covers (11).
Illustration 5 g01216098
5. Disconnect hose assemblies (15). Disconnect fitting (16). Disconnect hose assemblies (12).
Remove fittings (14). Remove bolts (13). Remove swivel (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:01:15 UTC+0800 2020
3/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02568407
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-3822 Bolt 2
6V-5839 Washer 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 1. Thoroughly clean the outside of the swivel joint prior to disassembly.
Illustration 1 g00633843
Illustration 2 g00633841
2. Use a suitable lifting device to position the swivel joint onto Tooling (B). Fasten the swivel joint to
Tooling (B), as shown. The weight of the swivel joint is approximately 43 kg (95 lb).
3. Remove bolts (1), washers (2), and cover (3) from outside housing (8).
4. Remove O-ring seal (7) from outside housing (8).
5. Remove bolts (4), washers (5), and retainer (6) from rotor (11).
2/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 6. Use Tooling (A) in order to separate the outside housing (8) from rotor (11). The weight of outside
housing (8) is approximately 20 kg (45 lb). The weight of rotor (11) is approximately 21 kg (46 lb).
7. Remove seals (9) from outside housing (8).
8. Remove O-ring seals (10) from the outside housing (8).
9. Remove plug (13). Remove O-ring seal (12) from plug (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:02:18 UTC+0800 2020
3/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02426337
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components,
if necessary.
1/2(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g00633843
1. Install O-ring seal (12) on plug (13). Apply clean hydraulic oil on the seal. Install plug (13).
2. Install seals (9) and O-ring seals (10) into outside housing (8).
3. Carefully install outside housing (8) over rotor (11).
4. Install retainer (6), washers (5), and bolts (4). This holds the rotor (11) and the outside housing (8)
together.
5. Apply clean hydraulic oil on O-ring seal (7). Install the O-ring seal in the outside housing.
6. Install cover (3), washers (2), and bolts (1) that secure the cover.
7. Check the swivel joint for leaks. Plug the drain ports of the inside body. Apply shop air pressure in
the top of the swivel joint and check the swivel joint for leaks. The shop air pressure should be
between 0.2758 MPa (40 psi) and 0.4137 MPa (60 psi).
End By:
a. Install the swivel joint. Refer to Disassembly and Assembly, "Swivel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:03:21 UTC+0800 2020
2/2(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434356
Swivel - Install
SMCS - 5060-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Illustration 1 g01216082
1. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Position swivel (9). Install boot (5) and clamp (7). Install
retainer (8) and bolts (6).
1/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g01216069
2. Connect hose assemblies (1), (2), and (3). Install support (4).
Illustration 3 g01216098
3. Install bolts (13). Install fittings (14). Install fitting (16). Connect hose assemblies (15).
Connect hose assemblies (14) and (12) to swivel (9).
Illustration 4 g01216099
4. Install covers (11) and bolts (10).
2/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 5 g01209599
5. Remove Tooling (A).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:04:24 UTC+0800 2020
3/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434311
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Remove
SMCS - 5479-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes
for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g00690963
1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the
hydraulic system.
2/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 2 g01206719
2. Open door (1).
Illustration 3 g01216136
3. Disconnect harness assemblies (4).
4. Disconnect hose assemblies (2) and (3).
5. Remove bolts (5) and solenoid valve (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:05:27 UTC+0800 2020
3/3(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434312
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Install
SMCS - 5479-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01216136
1/2(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 1. Install solenoid valve (6) and bolts (5).
2. Connect hose assemblies (2) and (3).
3. Connect harness assemblies (4).
Illustration 2 g01206719
4. Close door (1).
Illustration 3 g00690963
5. Remove Tooling (A) from the hydraulic tank.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:06:29 UTC+0800 2020
2/2(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02413351
Swing Cushion Valve - Remove
SMCS - 5454-015
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Illustration 1 g01206252
1. Disconnect hose assemblies (1) and (2). Disconnect harness assembly (4). Remove bolts (3)
and remove swing cushion valve (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 16:07:32 UTC+0800 2020
1/1(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR HAS
Configuration: 330D L Excavator HAS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02096925
Swing Cushion Valve - Disassemble - Fine Swing Solenoid
SMCS - 5454-015
Disassembly Procedure
Start By:
a. Remove the swing cushion valve. Refer to Disassembly and Assembly, "Swing Cushion
Valve - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
Illustration 1 g00702083
1. Remove O-ring seals (1) and (2) from the valve body.
2. Remove the fine swing solenoid, as follows.
1/4(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 2 g00702084
a. Remove bolts (3).
b. Remove fine swing solenoid (4).
Illustration 3 g00702085
c. Remove O-ring seal (8), (6), (7), and (5).
3. Remove the relief valves, as follows.
Illustration 4 g00702097
2/4(W)
w
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...