Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01333774
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00580923
1/2248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Remove eight bolts (1) from air inlet manifold (2) .
Illustration 2 g00580932
2. Remove air inlet manifold (2) and gasket (3) from the engine. Check the condition of gasket
(3). If gasket (3) is worn or damaged, use a new part for replacement.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 00:56:05 UTC+0800 2019
2/2248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01333848
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00581044
1. Install two guide bolts (4) into the cylinder head, as shown. The guide bolts are used to keep
gasket (3) and air inlet manifold (2) in position on the cylinder head during installation.
2. Put gasket (3) in position on the engine.
Illustration 2 g00580923
3. Put air inlet manifold (2) in position on the engine.
4. Install six of the eight bolts (1) and remove two guide bolts (4). Install the remaining two
bolts (1) .
5. Tighten bolts (1) to a torque of 22 N·m (16 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 00:57:01 UTC+0800 2019
2/2248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01458210
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Start By:
A. Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Before you begin the removal of the valve springs, refer to the Specifications Module,
"Cylinder Head Valves" topic for appropriate information on the valve springs.
1. Ensure that the piston is at the top center position.
Note: If the rocker arm assembly has not been removed, rotate the crankshaft in the normal
direction of rotation until the inlet valve of the appropriate cylinder has just opened and the
1/4248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. exhaust valve has not fully closed. If the rocker arm assembly has been removed, go to Step
2.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
Illustration 1 g00762206
a. Install Tool (A) .
b. Compress the valve springs in order to open the valve.
c. Turn the crankshaft until the piston touches the valve.
d. Continue to turn the crankshaft and release the pressure of Tool (A) until the piston is
at the top center position.
Illustration 2 g00762210
2. Install Tool (A) .
2/4248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 3. Compress valve springs (1). Remove two valve keepers (2) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
4. Release the pressure on Tool (A). Remove valve spring retainer (3) and valve springs (1) .
Note: If you are replacing all of the valve springs, the procedure can be done on two
cylinders at the same time. The procedure can be done on cylinder 1 and cylinder 4, or on
cylinder 2 and cylinder 3.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the new valve springs into position.
Note: Ensure that the closed damper coils are toward the cylinder head if double valve
springs are used.
3/4248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00762210
2. Install valve spring retainer (3) .
3. Install Tool (A). Compress valve springs (1) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
4. Install two valve keepers (2) .
5. Release the pressure slowly on Tool (A). Remove Tool (A). Strike the top of the valves with
a soft faced hammer in order to ensure that the valve keepers are properly installed.
Note: If you are replacing all of the valve springs the procedure can be done on two
cylinders at the same time. The procedure can be done on cylinder 1 and cylinder 4, or on
cylinder 2 and cylinder 3.
End By: Install the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 00:57:57 UTC+0800 2019
4/4248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01739737
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom face of the cylinder head. Use a dial indicator to check the depth of the
valves below the face of the cylinder head before the valve springs are removed. Refer to
Specifications, RENR2401, "Cylinder Head Valves" for the correct dimensions.
2. Place an index mark on the heads of the inlet valves and the exhaust valves for installation
purposes.
1/5248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00545731
3. Use Tooling (A) to compress inner springs (3) and outer springs (4).
Note: Some engines may have only a single inlet valve spring and a single exhaust valve
spring.
4. Remove valve keepers (1).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
2/5248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
5. Slowly release the pressure on Tooling (A) and remove Tooling (A).
6. Remove valve spring retainers (2).
7. Remove inner springs (3) and outer springs (4).
8. Remove seals (5).
9. Remove valve spring seat washers (6).
10. Remove inlet valves (7) and exhaust valves (7).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g00545731
1. Lubricate the stems of inlet valves (7) and the stems of exhaust valves (7) with clean engine
oil.
2. Install inlet valves (7) and exhaust valves (7) in the respective positions.
3. Install valve spring seat washers (6).
4. Install new seals (5).
5. Install inner springs (3) and outer springs (4).
4/5248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Install inner springs (3) and outer springs (4) on the valve spring seat washers with
the damper coils toward the cylinder head. This is done with double valve springs. If single
valve springs are used, the springs can be installed in either way.
6. Install valve spring retainers (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
7. Use Tooling (A) to compress inner springs (3) and outer springs (4).
Note: Some engines may have only a single inlet valve spring and a single exhaust valve
spring.
8. Install valve keepers (1).
9. Slowly release the pressure on Tooling (A) and remove Tooling (A). Strike the top of the
valves with a soft hammer in order to ensure that the valve keepers are properly installed.
Note: Refer to Specifications, RENR2401, "Cylinder Head Valves" for more information on
inlet valves and exhaust valves.
10. Use a dial indicator to check the depth of the new valves below the cylinder head. If the
depth of the new valves is below the correct depth, the valve seat inserts must be replaced.
Refer to Disassembly and Assembly, "Inlet and Exhaust Valve Seat Inserts - Remove and
Install".
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 00:58:53 UTC+0800 2019
5/5248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01632437
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2716 Valve Guide Driver 1
B FT-2717 Stop Collar 1
Start By:
A. Remove the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet
and Exhaust Valves - Remove and Install".
Illustration 1 g00808012
1/3248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00702790
1. Use Tool (A) in order to remove the valve guides from the cylinder head.
2. Repeat the procedure for the remaining valve guides.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2716 Valve Guide Driver 1
B FT-2717 Stop Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00632176
Typical example
1. Put the valve guide in position. Carefully tap the valve guide in order to start the
installation. Use Tool (A) and Tool (B) to seat the valve guide in the cylinder head.
2. Check the protrusion of the valve guides. The valve guides should protrude 7.70 to 7.85 mm
(0.303 to 0.309 inch) above the valve spring recess.
3. Repeat the procedure for the remaining valve guides.
Note: After installing the unfinished valve guides, you must ream the valve guides to the
finished diameter. Refer to Specifications, "Cylinder Head Valves" for the finished diameter
of the valve guides.
End By: Install the inlet valves and the exhaust valves. Refer to Disassembly and Assembly,
"Inlet and Exhaust Valves - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 00:59:48 UTC+0800 2019
3/3248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01556212
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool Group 1
6V-4196 Inlet Valve Seat Extractor (1)
1
6V-4195 Exhaust Valve Seat Extractor (1)
1
6V-4804 Handle Assembly (1)
1
( 1 )
This tool is included in the 166-7441 Valve Seat Extractor Tool Group .
Start By:
A. Remove the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet
and Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3248 Skid Steer Loader 6LZ01000-UP (MACHINE) POWERED BY 3034 Engine(SEB...
2019/11/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...