This document provides instructions for removing and installing an exhaust manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 330B excavator engine. The procedures include using various tools to remove exhaust manifold nuts, compress valve springs, extract valve guides and seats, and installing replacement parts in the proper positions while ensuring cleanliness to prevent premature wear.
Caterpillar cat 330 b excavator (prefix 5ez) service repair manual (5ez00001 ...hfjsekekmmd
This document provides instructions for removing an engine oil filter base from a 330B excavator. The procedure involves using a strap wrench to remove the oil filter, then removing bolts and tube assemblies from the cylinder block. O-ring seals in the tube assemblies should be inspected and replaced if needed. Fluids are to be contained and disposed of properly during maintenance.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...hhjsekmdmm
The document provides instructions for disassembling the piston pump of a M315C wheeled excavator. It describes removing 31 individual parts from the pump in a specific sequence, including the servo valve, charge pump, gears, head, relief valves, pistons, barrel assembly, swashplate assembly, and other components. Cleanliness is important during disassembly to prevent dirt from entering the internal mechanisms. Personal injury can result from hydraulic pressure still remaining in the system, so precautions must be taken.
Caterpillar cat 330 b excavator (prefix 5ez) service repair manual (5ez00001 ...hfjsekekmmd
This document provides instructions for removing an engine oil filter base from a 330B excavator. The procedure involves using a strap wrench to remove the oil filter, then removing bolts and tube assemblies from the cylinder block. O-ring seals in the tube assemblies should be inspected and replaced if needed. Fluids are to be contained and disposed of properly during maintenance.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...hhjsekmdmm
The document provides instructions for disassembling the piston pump of a M315C wheeled excavator. It describes removing 31 individual parts from the pump in a specific sequence, including the servo valve, charge pump, gears, head, relief valves, pistons, barrel assembly, swashplate assembly, and other components. Cleanliness is important during disassembly to prevent dirt from entering the internal mechanisms. Personal injury can result from hydraulic pressure still remaining in the system, so precautions must be taken.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 248 b skid steer loader (prefix scl) service repair manual (s...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a 248B skid steer loader with a 3044C engine. It outlines the required tools and multi-step procedures, which include using air pressure to hold the valves in place while removing and installing the springs. Safety notices are included to warn of potential injury from parts propelled by spring force. The document also provides instructions for removing and installing inlet and exhaust valve guides and seats.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and servicing components of a 436B backhoe loader engine, including:
1) Removing the cylinder head by first removing other components and then gradually loosening and removing 22 bolts.
2) Disassembling the rocker shaft by removing retaining rings and disassembling the shaft, arms, and brackets.
3) Reassembling the rocker shaft by lubricating parts and installing them in the correct order onto the shaft.
4) Installing the rocker shaft and pushrods by positioning them correctly and adjusting valve lash.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fikkskkdmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to extract the old seat inserts and press in the new ones. Technicians are advised to keep all parts clean and lubricated to prevent wear during reassembly.
Caterpillar Cat 330B L EXCAVATOR (Prefix 1JS) Service Repair Manual (1JS00001...jdjkskmikdkmd
This document provides instructions for removing and installing various engine components on a 330B L Excavator, including:
1. The exhaust manifold, which is removed by taking off nuts and washers, and installing in reverse order.
2. Inlet and exhaust valves, which are compressed with a tool to remove keepers and springs, then reinstalled in cylinders.
3. Valve guides, which are driven out and replaced using a driver tool and collar.
4. Valve seat inserts, which are extracted and new ones installed using an extractor tool.
5. The engine oil filter base, which is removed by taking off the filter and bolts.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...udjdkkmdmdm
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to extract the old seat inserts and press in the new ones. Technicians are advised to keep all parts clean and lubricated to prevent damage and wear. Precise measurement is required to ensure the inserts are installed to the correct depth. Following the steps helps complete the valve seat service efficiently.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fikkskmmdm
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to press the inserts out of the cylinder head. New inserts are then pressed into place with the same tool and checked for proper depth. The instructions note to keep all parts clean from contamination to prevent premature wear.
Caterpillar Cat 330B L EXCAVATOR (Prefix 1JS) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to press the inserts out of the cylinder head. New inserts are then pressed into place with the same tool and checked for proper depth. The instructions note to keep all parts clean from contamination to prevent premature wear.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fjskefkemms
This document provides instructions for removing and installing various engine components on a 330B L EXCAVATOR, including:
- Exhaust manifold removal and installation requiring removal of the turbocharger and fuel lines.
- Inlet and exhaust valve removal and installation using specialized tools to compress springs.
- Removal and installation of valve guides, seats, and inserts using driver tools to precisely install components.
- Removal of the engine oil filter base requiring a strap wrench to remove the oil filter.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert parts, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...fuusejkddmmd3e
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert parts, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...dujkdksmdmdm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 248 b skid steer loader (prefix scl) service repair manual (s...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a 248B skid steer loader with a 3044C engine. It outlines the required tools and multi-step procedures, which include using air pressure to hold the valves in place while removing and installing the springs. Safety notices are included to warn of potential injury from parts propelled by spring force. The document also provides instructions for removing and installing inlet and exhaust valve guides and seats.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and servicing components of a 436B backhoe loader engine, including:
1) Removing the cylinder head by first removing other components and then gradually loosening and removing 22 bolts.
2) Disassembling the rocker shaft by removing retaining rings and disassembling the shaft, arms, and brackets.
3) Reassembling the rocker shaft by lubricating parts and installing them in the correct order onto the shaft.
4) Installing the rocker shaft and pushrods by positioning them correctly and adjusting valve lash.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fikkskkdmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to extract the old seat inserts and press in the new ones. Technicians are advised to keep all parts clean and lubricated to prevent wear during reassembly.
Caterpillar Cat 330B L EXCAVATOR (Prefix 1JS) Service Repair Manual (1JS00001...jdjkskmikdkmd
This document provides instructions for removing and installing various engine components on a 330B L Excavator, including:
1. The exhaust manifold, which is removed by taking off nuts and washers, and installing in reverse order.
2. Inlet and exhaust valves, which are compressed with a tool to remove keepers and springs, then reinstalled in cylinders.
3. Valve guides, which are driven out and replaced using a driver tool and collar.
4. Valve seat inserts, which are extracted and new ones installed using an extractor tool.
5. The engine oil filter base, which is removed by taking off the filter and bolts.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...udjdkkmdmdm
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to extract the old seat inserts and press in the new ones. Technicians are advised to keep all parts clean and lubricated to prevent damage and wear. Precise measurement is required to ensure the inserts are installed to the correct depth. Following the steps helps complete the valve seat service efficiently.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fikkskmmdm
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to press the inserts out of the cylinder head. New inserts are then pressed into place with the same tool and checked for proper depth. The instructions note to keep all parts clean from contamination to prevent premature wear.
Caterpillar Cat 330B L EXCAVATOR (Prefix 1JS) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 330B L excavator engine. The procedure involves using a special tool to press the inserts out of the cylinder head. New inserts are then pressed into place with the same tool and checked for proper depth. The instructions note to keep all parts clean from contamination to prevent premature wear.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fjskefkemms
This document provides instructions for removing and installing various engine components on a 330B L EXCAVATOR, including:
- Exhaust manifold removal and installation requiring removal of the turbocharger and fuel lines.
- Inlet and exhaust valve removal and installation using specialized tools to compress springs.
- Removal and installation of valve guides, seats, and inserts using driver tools to precisely install components.
- Removal of the engine oil filter base requiring a strap wrench to remove the oil filter.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert parts, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...fuusejkddmmd3e
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert parts, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...dujkdksmdmdm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...jdksmmdmdd
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert parts, and check spring forces. Precautions are given to keep parts clean and prevent damage during the processes.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...fujkse9didkke3
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
Similar to Caterpillar cat 330 b excavator (prefix 5ez) service repair manual (5ez00001 and up) (20)
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The installation procedure specifies applying lubricant to new seals before reconnecting the governor components using the same special tools. Technicians are referred to other documents for additional information on testing, adjusting, and inspecting the governor and linkage components.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are listed to prevent contamination and contain fluids. Required tools are also identified.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...diskkdkdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 l excavator (prefix 8nk) service repair manual (8nk00001 ...diskkdkdmdm
This document provides instructions for installing pistons and connecting rods in a Caterpillar 3116 engine. It outlines 13 steps for the installation, including cleaning and lubricating parts, inserting piston rings, lining up the piston and connecting rod, and torquing connecting rod cap bolts. Tools and torque specifications are listed in tables. The summary also refers to other documents providing guidance on determining whether parts can be reused.
Caterpillar cat 325 l excavator (prefix 7lj) service repair manual (7lj00001 ...diskkdkdmdm
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and remove clips and pins connecting the governor to the engine. The installation procedure specifies cleaning and lubricating parts before reinstalling components using the same special tools to connect the governor and linkage. Proper adjustment of settings is required after installation.
Caterpillar cat 325 l excavator (prefix 2sk) service repair manual (2sk00001 ...diskkdkdmdm
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
Caterpillar cat 325 l excavator (prefix 2jk) service repair manual (2jk00001 ...diskkdkdmdm
1) The document provides disassembly instructions for the final drive on 325 and 325L excavators. It describes removing over 30 parts in multiple steps, requiring various tools.
2) Key steps include removing the final drive cover, ring gear, carrier assemblies, planetary gears, seals, and bearings from the main housing. Precision is required to note part positions for reassembly.
3) Disassembly of the final drive is complex, with many heavy parts that require lifting equipment to handle safely. Thorough cleaning is important before disassembly.
Caterpillar cat 325 f l excavator (prefix rbw) service repair manual (rbw0000...diskkdkdmdm
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 325 f l excavator (prefix ndj) service repair manual (ndj0000...diskkdkdmdm
This document provides instructions for disassembling and assembling the travel motor of 325F and 325F L excavator models. The disassembly procedure involves removing 31 parts from the travel motor in 30 steps. The assembly procedure instructs assembling the travel motor in 11 steps and provides notices on properly installing keys to prevent damage. Key steps include using tools and lifting devices to remove heavy components like the head assembly and housing assembly, and ensuring parts are clean before assembly.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...diskkdkdmdm
The document provides instructions for disassembling and assembling the travel motor of an excavator model 325F. It involves 25 steps to disassemble the various components of the travel motor including removing the head, brake piston, barrel assembly, shoe retainer and more. The 23 steps for assembly involve installing these same components in reverse order, making sure to apply grease and seals correctly. Precise alignment and positioning of parts is important for correct reassembly.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...diskkdkdmdm
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing lips seals, keys, cam plate, barrel assembly, piston guide and more. Detailed illustrations accompany each step to ensure proper reassembly. Precautions are provided to prevent injury from released springs and to correctly install parts like the cam plate.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...diskkdkdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Specifications for determining if used parts can be reused are also referenced.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...diskkdkdmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing other components first. It then outlines 11 steps to install the cylinder head, including cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar cat 325 l excavator (prefix 2 sl) service repair manual (2sl00001...diskkdkdmdm
This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Guidelines are provided for determining whether used parts can be reused.
This document provides instructions for installing pistons and connecting rods and crankshaft main bearings in a Caterpillar 3116 engine. It outlines 13 steps for piston and connecting rod installation, including cleaning parts, applying oil, inserting pistons into cylinders, and torquing connecting rod cap bolts. It also describes 3 steps for removing crankshaft main bearings, such as using a bearing tool, and checking bearing condition.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and remove clips and pins connecting the governor to the engine. The installation procedure specifies cleaning and lubricating parts before reinstalling components using the same special tools to connect the governor and linkage. Proper adjustment of settings is required after installation.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01041426
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00537836
1/5(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 1. Remove two nuts (1), the washers and the heat shield from the exhaust manifold.
Illustration 2 g00537855
2. Remove bolt (3) from the bracket that holds two of the fuel injection lines in position.
Loosen nuts (2) and (4) and remove the two fuel injection lines from the engine. Put
protective caps on the fuel injectors and put protective caps on the fuel injection pump in
order to prevent contamination.
Illustration 3 g00537885
3. Remove the remaining ten exhaust manifold nuts (5) and the large washers. Remove
exhaust manifold (6).
2/5(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g00541058
4. Remove three exhaust manifold gaskets (7) from the cylinder head and the twelve exhaust
manifold studs, if necessary. Make sure that the position of the two longer studs are marked
for proper installation.
Installation Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. If the twelve exhaust manifold studs were removed, apply 5P-3931 Anti-Seize Compound
to both ends of the exhaust manifold studs and install the studs in the cylinder head. Make
sure that the two longer studs are installed in the correct position. Tighten the studs to a
torque of 27 ± 4 N·m (20 ± 3 lb ft).
3/5(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00541058
2. Put three exhaust manifold gaskets (7) in position on the cylinder head.
Illustration 6 g00537885
3. Install exhaust manifold (6). Install ten washers and nuts (5). The two longer studs are for
the installation of the heat shield. Tighten exhaust manifold nuts (5) to a torque of 47 ± 4
N·m (35 ± 3 lb ft).
Illustration 7 g00537855
4/5(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 4. Remove the protective caps from the fuel injectors and the fuel injection pump. Put the fuel
injection lines in position and tighten nuts (2) and (4) finger tight. Install bolt (3) in the
bracket that holds the fuel injection lines in position. Tighten nuts (3) and (4) with Tool (A)
to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 8 g00537836
5. Install the two large washers and the spacers on the two remaining exhaust manifold studs.
Install heat shield (1) and the remaining two washers and exhaust manifold nuts that fasten
heat shield (1) to the exhaust manifold. Tighten the two nuts to a torque of 47 ± 4 N·m (35 ±
3 lb ft).
6. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel system -
Prime" topic (Maintenance Section).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:44:59 UTC+0800 2020
5/5(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00962627
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 8S-2263 Valve Spring Tester 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and assembly, "Cylinder Head - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00490614
1. Use Tool (A) to compress valve spring (2) and remove valve keepers (1) .
2. Remove Tool (A), the rotocoil, the valve spring and the valve stem oil shield. Remove the
valve from the cylinder head. Put identification marks on the valves for installation
purposes.
Illustration 2 g00490682
3. Check the valve spring force with Tool (B). Refer to Specifications, "Cylinder Head
Valves" for information on the valve springs.
4. Perform Steps 1 through 3 for the remaining inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 5S-1322 Valve Keeper Inserter 1
2/4(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the inlet and exhaust valves with clean engine oil. Install the inlet and exhaust
valves in the original location in the cylinder head.
Illustration 3 g00508681
2. Install valves (3), oil shield (4), valve spring (2) and rotocoil (1) in the cylinder head.
Illustration 4 g00490777
3. Use Tool (A) to compress valve spring (2). Install valve keeper (5) on the valve stem with
Tool (B) .
3/4(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
4. Carefully remove Tool (A). Strike the top of the valve with a soft faced hammer in order to
ensure that the valve keepers are properly installed.
5. Repeat Steps 3 through 4 for the remaining inlet and exhaust valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:45:55 UTC+0800 2020
4/4(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00962891
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7349 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 1 g00490787
1. Use Tool (A) to remove the inlet and exhaust valve guides from the cylinder head.
2. Repeat Step 1 for the remaining inlet and exhaust valve guides.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-7349 Valve Guide Driver 1
B 9U-6954 Valve Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 2 g00490790
1. Put clean engine oil on the outside diameter of the valve guide. Install the valve guide with
Tool (A) and Tool (B), as shown.
Illustration 3 g00508601
2. Dimension (X) from the top of the valve guide to the cylinder head must be 22.23 ± 0.25
mm (0.875 ± 0.010 inch). For more information on the inlet and exhaust valve guides, refer
to Specifications, "Cylinder Head Valves".
Note: In order to help prevent damage to the valve guides, Tool (B) must be used during
installation.
3. Repeat Steps 1 and 2 for the remaining inlet and exhaust valve guides.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:46:51 UTC+0800 2020
3/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02107684
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4805 Valve Seat Extractor Tool Group 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00490857
1. Use Tooling (A) in order to remove the valve seat insert from the cylinder head.
2. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
3. Repeat Steps 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 6V-4805 Valve Seat Extractor Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g00508515
1. Shrink the new valve insert with reduced temperature. Use Tooling (A) in order to install
the new valve seat insert in the cylinder head.
Note: Do not increase the diameter of the extractor in the valve seat insert when the insert is
installed in the cylinder head.
2. Repeat Step 1 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:47:47 UTC+0800 2020
3/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00981264
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
1/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00499430
1. Remove the oil filter from engine oil filter base (1) with Tool (A).
Illustration 2 g00499568
2. Remove bolts (5), tube assembly (3) and the gasket. Remove the O-ring seal in tube
assembly (3) and replace the O-ring seal, if necessary.
3. Remove the bolts that hold tube assembly (4) to the cylinder block. Remove tube assembly
(4) and the gasket. Remove the O-ring seal in tube assembly (4) and replace the O-ring seal,
if necessary.
4. Remove four bolts (2) and engine oil filter base (1) from the cylinder block. Remove the O-
ring seals from engine oil filter base (1), if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:48:42 UTC+0800 2020
2/3(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00983225
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
A. Remove the engine oil filter and the engine oil filter base. Refer to Disassembly and
Assembly, "Engine Oil Filter Base - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00500551
1/2(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Typical Example
Illustration 2 g00500559
Typical Example
1. Remove O-ring seals (1) from the engine oil filter base. Remove four bolts (2), two covers
(3) and two gaskets (6) .
Note: Plunger (4) is for the oil filter bypass. Plunger (7) is for the engine oil cooler bypass.
2. Remove springs (5), plunger (4) and plunger (7) from the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:49:38 UTC+0800 2020
2/2(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00983561
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00500559
1/2(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 2 g00500551
1. Install plunger (7), plunger (4) and springs (5) .
Note: Plunger (7) is for the engine oil cooler bypass. Plunger (4) is for the oil filter bypass.
Note: Check the condition of the O-ring seals and gaskets. If the seals or gaskets are worn
or damaged, use new parts for replacement.
2. Install two gaskets (6), two covers (3), four bolts (2) and O-ring seals (1) .
End By: Install the engine oil filter base and the oil filter. Refer to Disassembly and Assembly,
"Engine Oil Filter Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:50:34 UTC+0800 2020
2/2(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 5EZ
Configuration: ISJ HEX COMMONALITY CHART 5EZ00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00981970
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Check the condition of the O-ring seals and the gaskets. If the seals or the gaskets are worn
or damaged, use new parts for replacement.
1/2(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 1 g00499568
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
2. Put the O-ring seals on engine oil filter base (1). Install engine oil filter base (1) on the
cylinder block with four bolts (2) .
3. Put the O-ring seal and the gasket in position on tube assembly (4). Install tube assembly (4)
on the cylinder block. Install the bolts that hold tube assembly (4) in position.
4. Put the O-ring seal and the gasket in position on tube assembly (3). Fasten the clip to tube
assembly (4). Position tube assembly (3) onto the cylinder block and install bolts (5).
Illustration 2 g00499430
5. Install engine oil filter (1) with Tool (A) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 19:51:30 UTC+0800 2020
2/2(W)
w
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...