1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a 325L excavator.
2. It describes using a valve spring compressor tool to compress the valve spring when removing or installing valves. Proper lubrication and cleaning of parts is emphasized.
3. Instructions include tapping new valve guides into position in the cylinder head using driver tools to fully seat the guides. Reusing parts is addressed by referring to other guideline documents.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...shudun96087
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...qme229722
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...kesi7153062
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...shudun96087
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...qme229722
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...kesi7153062
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts and install new ones, ensuring the parts are clean from contaminants. References are provided for determining if valve seats can be reused.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...kesi7153062
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. Installation is the reverse, applying a new O-ring seal and reconnecting all lines. Proper cleaning and containment of fluids is emphasized. The document outlines procedures for both non-dual and dual tapered roller bearing pump types.
Caterpillar Cat 336D2 L Excavator (Prefix EF3) Service Repair Manual (EF30000...kesi7153062
The document provides instructions for disassembling a 336D2 and 336D2 L excavator travel motor. It describes 27 steps to remove parts like the motor head assembly, springs, seals, plates, pistons, bearings and other components. Various tools are required including bolts, pins, retaining rings and specialty tools like bearing pullers and drivers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336D2 L Excavator (Prefix DGR) Service Repair Manual (DGR0000...kesi7153062
This document provides instructions for installing and removing unit injector sleeves on a Caterpillar C9 engine. It outlines the required tools and multi-step procedures for cleaning and preparing the sleeves and cylinder head, installing new seals, and using specialty tools to correctly position and secure the sleeves. Special care must be taken to avoid contaminating parts and ensure proper installation of seals to prevent oil leakage and engine performance issues.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D2 GC excavator. It describes 30 steps to disassemble the pump, removing components like the head, seals, bearings, pistons, and housing. It also describes 25 steps to reassemble the pump and install all components in the reverse order. Safety warnings are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of Caterpillar 336D2 and 336D2 L excavators. The disassembly procedure involves removing 30 parts in 8 steps, taking precautions for spring-loaded parts. The assembly procedure reinstalls the parts in 30 steps, heating and cooling certain parts, using tools such as retaining ring pliers and a dial indicator, and ensuring proper shim thickness and end play. Precautions are given to prevent injury from spring-loaded parts.
More Related Content
Similar to Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and up).pdf
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts and install new ones, ensuring the parts are clean from contaminants. References are provided for determining if valve seats can be reused.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Similar to Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and up).pdf (17)
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...kesi7153062
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. Installation is the reverse, applying a new O-ring seal and reconnecting all lines. Proper cleaning and containment of fluids is emphasized. The document outlines procedures for both non-dual and dual tapered roller bearing pump types.
Caterpillar Cat 336D2 L Excavator (Prefix EF3) Service Repair Manual (EF30000...kesi7153062
The document provides instructions for disassembling a 336D2 and 336D2 L excavator travel motor. It describes 27 steps to remove parts like the motor head assembly, springs, seals, plates, pistons, bearings and other components. Various tools are required including bolts, pins, retaining rings and specialty tools like bearing pullers and drivers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336D2 L Excavator (Prefix DGR) Service Repair Manual (DGR0000...kesi7153062
This document provides instructions for installing and removing unit injector sleeves on a Caterpillar C9 engine. It outlines the required tools and multi-step procedures for cleaning and preparing the sleeves and cylinder head, installing new seals, and using specialty tools to correctly position and secure the sleeves. Special care must be taken to avoid contaminating parts and ensure proper installation of seals to prevent oil leakage and engine performance issues.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D2 GC excavator. It describes 30 steps to disassemble the pump, removing components like the head, seals, bearings, pistons, and housing. It also describes 25 steps to reassemble the pump and install all components in the reverse order. Safety warnings are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of Caterpillar 336D2 and 336D2 L excavators. The disassembly procedure involves removing 30 parts in 8 steps, taking precautions for spring-loaded parts. The assembly procedure reinstalls the parts in 30 steps, heating and cooling certain parts, using tools such as retaining ring pliers and a dial indicator, and ensuring proper shim thickness and end play. Precautions are given to prevent injury from spring-loaded parts.
This document provides instructions for installing and removing the final drive and travel motor, and disassembling and assembling the swivel, on Caterpillar 336D2 and 336D2 L excavators. The procedures include using various tools to lift heavy components, installing and tightening bolts, replacing O-rings and seals, and checking for leaks during assembly. Cleanliness is emphasized to prevent contamination.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
1. The document provides instructions for disassembling and assembling the piston pump of a 336D2 excavator.
2. It details 30 steps for assembly, including installing various parts like bearings, seals, springs, and fasteners.
3. Instructions are accompanied by illustrations and warnings about safety and cleanliness.
This document provides instructions for disassembling a travel motor on a 336D2 L excavator. The process involves 27 steps and uses various tools. Key steps include removing the motor head assembly, springs, spools, relief valves, plugs and O-rings. Safety precautions are provided to release spring forces without injury.
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse, applying a new O-ring seal and grease, positioning the pump, and reconnecting all lines and bolts. Proper cleaning and containment of fluids is emphasized to prevent contamination.
The document provides instructions for disassembling a 336D2 and 336D2 L excavator travel motor. It describes 27 steps to remove parts like the motor head assembly, springs, seals, plates, pistons, bearings and other components. Various tools are required including bolts, pins, retaining rings and specialty tools like bearing pullers and drivers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
This document provides instructions for removing and installing unit injectors and unit injector sleeves on a Caterpillar C9 engine. It outlines the required tools and safety procedures. The procedures include draining fluids, removing injectors, cleaning parts, installing new seals, and reinstalling injectors and sleeves. Special care must be taken to properly install seals and avoid damaging parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on Caterpillar 336D L and 336D LN excavators. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can propel parts, while the assembly follows 30 steps to reinstall all parts in the reverse order. Tools include retaining ring pliers, a dial indicator, and a bearing puller. The document emphasizes cleanliness during assembly and replacing any worn parts.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...kesi7153062
1. The document provides instructions for disassembling and assembling a piston pump used in a hydraulic excavator fan.
2. The disassembly process involves using various tools to remove over 30 individual parts from the pump in sequential order.
3. Reassembly requires carefully installing each part in reverse order, ensuring proper placement of seals, bearings, springs and other components.
4. Cleanliness is emphasized throughout to prevent contamination during assembly.
Caterpillar Cat 336D L Excavator (Prefix WET) Service Repair Manual (WET00001...kesi7153062
The document provides instructions for removing the final drive and travel motor, and swivel, from an excavator model 336D L. Key steps include:
1. Separating the track, disconnecting hydraulic hoses, and removing bolts to detach the final drive and travel motor assembly.
2. Removing O-rings and bolts to separate the travel motor from the final drive.
3. Releasing hydraulic pressure before removing the swivel.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...kesi7153062
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...kesi7153062
1. The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L excavator.
2. The disassembly process includes removing 30 individual parts in 9 steps, taking care with spring-loaded components.
3. Reassembly requires installing the parts in reverse order, with 30 steps to install all components and ensure proper operation.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...kesi7153062
The document provides instructions for removing and installing the final drive and travel motor assembly on a 336D L excavator. Key steps include:
1. Removing hoses, fittings, bolts and covers to access the assembly.
2. Attaching lifting tools and carefully removing the heavy final drive and travel motor unit.
3. Inspecting and replacing seals if needed before reinstalling the component and reconnecting all hoses and fittings. Proper torque is applied to bolts during reinstallation.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...kesi7153062
The document provides instructions for assembling and disassembling the swivel component of an excavator. It outlines the required tools and safety procedures. The assembly procedure involves cleaning parts, positioning the swivel joint using lifting devices, and installing seals, housings, and fittings in the correct order while applying lubricants. The disassembly process is the reverse and uses specialized tools to separate components. Proper cleaning and containment of fluids is emphasized throughout.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:31:27 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:32:22 UTC+0800 2020
5/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:33:18 UTC+0800 2020
4/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:34:14 UTC+0800 2020
4/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:35:10 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:36:05 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:37:01 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:37:57 UTC+0800 2020
3/3
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...