1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a 325L excavator.
2. It describes using a valve spring compressor tool to compress the valve spring when removing or installing valves. Proper lubrication and cleaning of parts is emphasized.
3. Instructions include tapping new valve guides into position in the cylinder head using driver tools to fully seat the guides. Reusing parts is addressed by referring to other guideline documents.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...shudun96087
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...qme229722
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...kesi7153062
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...shudun96087
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...qme229722
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to other documents for specifications on the reusability of valve seats.
Caterpillar Cat 325 L EXCAVATOR (Prefix 2SL) Service Repair Manual (2SL00001 ...kesi7153062
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325 L excavator. It begins with an overview of the required tools and safety notices. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure is not described, but refers the technician to install the new valve seat inserts using the same tools. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts and install new ones, ensuring the parts are clean from contaminants. References are provided for determining if valve seats can be reused.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
The document provides instructions for disassembling a travel motor on an excavator model 330F. It lists 28 steps to completely disassemble the travel motor, including removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Various specialized tools are required to properly support, remove, and disassemble the parts in the correct sequence. Safety precautions are provided throughout to warn of potential spring forces or pressurized air when disassembling parts.
Caterpillar Cat 330D2 L Excavator (Prefix PTE) Service Repair Manual (PTE0000...shudun96087
This document provides instructions for removing and installing a turbocharger on Caterpillar 330D2 L excavator engines. The removal process involves disconnecting hoses and tubes, removing mounting bolts and nuts, and taking off the turbocharger. For installation, the instructions specify cleaning components, applying anti-seize compound to studs, mounting the turbocharger using nuts and bolts, and orienting and securing connecting tubes with gaskets and specified torques. Tools including a rubber lubricant and anti-seize compound are listed. Safety notices advise keeping components clean and containing fluids.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...shudun96087
This document provides disassembly and assembly instructions for the final drive of a 330D2 excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the final drive assembly including gears, shafts, carriers, seals and housings. The assembly procedure instructs how to reinstall these parts in reverse order and also describes how to properly set the bearing preload using shims.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...shudun96087
This document provides disassembly instructions for a final drive system. It outlines 33 steps to fully disassemble the drive, including removing covers, gears, carriers, shafts, seals, and housing components. Various tools are required, and notes provide guidance on cleaning, marking parts, and safely lifting heavy components. Detailed illustrations accompany each step to show the assembly views and identified parts.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides details on installing seals, adjusting bearing preload using shims, and torquing bolts to specifications.
More Related Content
Similar to Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and up).pdf
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...hfjsekekmmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It describes the required tools and gives a multi-step process including using a valve seat extractor tool to remove the inserts from the cylinder head and install new inserts. References are provided for determining if valve seats can be reused and the appropriate specifications.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...jdfjskekmdme
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325L excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts and install new ones, ensuring the parts are clean from contaminants. References are provided for determining if valve seats can be reused.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...cdfzxs
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325L excavator engine:
1. Use a valve guide driver tool to remove the old valve guides from the cylinder head. Keep all parts clean from contaminants.
2. Position the new inlet valve guides in the cylinder head and use a driver tool and guide collar to fully install them. Repeat for the exhaust valve guides.
3. Reinstall the inlet and exhaust valves following the specified procedure using a valve spring compressor tool.
Similar to Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and up).pdf (17)
The document provides instructions for disassembling a travel motor on an excavator model 330F. It lists 28 steps to completely disassemble the travel motor, including removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Various specialized tools are required to properly support, remove, and disassemble the parts in the correct sequence. Safety precautions are provided throughout to warn of potential spring forces or pressurized air when disassembling parts.
Caterpillar Cat 330D2 L Excavator (Prefix PTE) Service Repair Manual (PTE0000...shudun96087
This document provides instructions for removing and installing a turbocharger on Caterpillar 330D2 L excavator engines. The removal process involves disconnecting hoses and tubes, removing mounting bolts and nuts, and taking off the turbocharger. For installation, the instructions specify cleaning components, applying anti-seize compound to studs, mounting the turbocharger using nuts and bolts, and orienting and securing connecting tubes with gaskets and specified torques. Tools including a rubber lubricant and anti-seize compound are listed. Safety notices advise keeping components clean and containing fluids.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...shudun96087
This document provides disassembly and assembly instructions for the final drive of a 330D2 excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the final drive assembly including gears, shafts, carriers, seals and housings. The assembly procedure instructs how to reinstall these parts in reverse order and also describes how to properly set the bearing preload using shims.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...shudun96087
This document provides disassembly instructions for a final drive system. It outlines 33 steps to fully disassemble the drive, including removing covers, gears, carriers, shafts, seals, and housing components. Various tools are required, and notes provide guidance on cleaning, marking parts, and safely lifting heavy components. Detailed illustrations accompany each step to show the assembly views and identified parts.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides details on installing seals, adjusting bearing preload using shims, and torquing bolts to specifications.
This document provides disassembly instructions for a final drive system. It outlines 32 steps to fully disassemble the drive, including removing covers, gears, carriers, shafts, seals, and housing components. Various tools are required, and notes provide guidance on cleaning, marking parts, weight of components, and pressing/lifting procedures. Detailed illustrations accompany each step.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...shudun96087
The document provides instructions for removing the final drive and travel motor assembly from a 330D L hydraulic excavator. It lists the required tools and safety precautions. The procedure involves applying vacuum pressure to the hydraulic system, disconnecting hoses, and removing bolts to detach the final drive and travel motor assembly using lifting tools. Markings are to be made to ensure correct reinstallation orientation.
Caterpillar Cat 330D L Mobile Hydraulic Excavator (Prefix H3D) Service Repair...shudun96087
This document provides instructions for removing and installing rear gear group components on a 330D L excavator with a C9 engine. The removal procedure involves using tools to remove retaining bolts and gears. Bearings are removed from adapters using specialized tools. Clearances are checked when installing new bearings. The installation procedure specifies matching angles and distances when pressing bearings in place and reinstalling gears and covers. Torques are provided for reinstalling bolts.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...shudun96087
This document provides instructions for removing and installing the final drive and travel motor on a 330D L hydraulic excavator. The removal procedure involves disconnecting hoses, removing bolts and fittings, and lifting the final drive and travel motor assembly out of the machine. The installation procedure describes reinstalling components in the reverse order and includes precautions for ensuring components are clean and properly torqued.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...shudun96087
The document provides instructions for removing and installing the rear gear group on a 330D L excavator. It describes in detail:
- Removing the flywheel and pump drive gear.
- Removing bolts and parts like retainers, gears, bushings, adapters, bearings, and covers to disassemble the rear gear group.
- Cleaning requirements and using special tools during removal and installation.
- Installing corresponding parts in reverse order and ensuring proper positioning and torque specifications are followed.
The summary focuses on the high-level steps of removing the flywheel, disassembling the rear gear group by removing multiple bolts and parts, cleaning requirements, and reinstalling parts in reverse order
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...shudun96087
The document provides instructions for removing and disassembling the swivel component of an excavator. Key steps include:
1. Releasing hydraulic pressure and disconnecting hose assemblies.
2. Removing bolts and covers to access the swivel.
3. Lifting the swivel out after disconnecting remaining fittings and hoses.
4. Cleaning and positioning the swivel on a repair stand for disassembly.
5. Separating the outside housing from the rotor by removing bolts, washers, and other retaining components.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual (HAS00001...shudun96087
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly to prevent damage. It instructs installing new O-rings and seals if worn. The steps include positioning the rotor and outside housing using lifting tools, applying the seals and O-rings, and securing with bolts, washers, and covers while torquing to the specified values. Proper cleaning and inspection of parts is emphasized to avoid contamination issues.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...shudun96087
This document provides instructions for removing and installing the camshaft on a Caterpillar C9 engine. The removal procedure involves using a hook tool to lift each camshaft lobe out of the cylinder head after removing the rocker arm and shaft assembly. The installation procedure specifies applying lubricant to the camshaft lobes before positioning them back into the cylinder head using the hook tool. Proper lubrication and placement of parts is emphasized to prevent premature wear and failure.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...shudun96087
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...shudun96087
This document provides instructions for removing and installing an operator console on an excavator. It begins by removing the seat and then removing plates (1) and (2). Hoses, lines, wires and tubes are identified and plugged to prevent fluid loss and contamination. Screws are removed from the console mounting brackets and the console is lifted off. Reinstallation follows the removal steps in reverse.
This service repair manual provides instructions for repairing 330D and 330D L excavators. It details the process for removing and installing the cylinder head, which includes draining coolant, removing mounting bolts and hoses, and lifting the head off using a lifting bracket. It also provides instructions for removing and installing the camshaft, which involves aligning timing marks, removing mounting bolts, and sliding the camshaft in and out of the engine block. Precautions are given to keep parts clean and avoid damaging lobes or bearings during removal and installation.
The document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves:
1. Removing all grease from the swing gear and bearing and placing it in a suitable container.
2. Marking the swing gear and bearing and frame for reassembly.
3. Using lifting equipment and link brackets to support the swing gear and bearing while removing bolts.
4. Removing the 280 kg swing gear and bearing assembly.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...shudun96087
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes how to remove and install the cylinder head, which involves draining coolant, removing accessories, sensors and bolts, and lifting the head off. It also details removing and installing the lifter group by using tools to pull lifters from the cylinder block and lubricating them before replacing in their original locations. Precautions are given to keep parts clean and contain fluids during repair work.
The documents provide instructions for removing and installing components related to the valve train of a Caterpillar 330B excavator engine, including:
- Removing the cylinder head by detaching various lines and manifolds, then removing bolts and lifting the head off
- Disassembling the rocker shaft by removing supports, arms, springs and the shaft itself
- Assembling the rocker shaft by installing the above components in reverse order
- Removing the rocker shaft and pushrods
- Installing the rocker shaft and pushrods, adjusting valve lash and tightening bolts in a specific sequence
The documents emphasize cleaning parts and containing fluids to prevent contamination and properly disposing of
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:31:27 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:32:22 UTC+0800 2020
5/5
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:33:18 UTC+0800 2020
4/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:34:14 UTC+0800 2020
4/4
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:35:10 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:36:05 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:37:01 UTC+0800 2020
2/2
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 6KK
Configuration: 325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 22:37:57 UTC+0800 2020
3/3
325, 325L TRACK TYPE EXCAVATORS 6KK00001-UP (MACHINE) POWERED ...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...