The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized throughout and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, including a press, hammer, and pullers. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive unit from the machine and then disassembling it into individual components. These include removing gears, carriers, shafts, seals, and other parts. Precautions are outlined regarding cleanliness and lubrication. Required tools are listed. The assembly procedure then provides mirrored instructions for reassembling the final drive unit.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, with attention to cleanliness and proper part labeling.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive from the machine, disassembling the internal components, and assembling the components back into the final drive housing. The procedures involve removing retaining rings, gears, shafts, seals, and other parts. Special tools are required and cleanliness is important when disassembling and assembling. Weights of removed parts are provided to assist with lifting.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...pwg56547003
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336D2 L Excavator (Prefix HBH) Service Repair Manual (HBH0000...pwg56547003
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It details 27 steps to remove over 50 individual parts, placing components in order and marking locations for reassembly.
3) Special care is required when removing parts under spring pressure or that could fall, and clean-up of fluids is important.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, including a press, hammer, and pullers. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 c excavator (prefix jld) service repair manual (jld00001 ...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive unit from the machine and then disassembling it into individual components. These include removing gears, carriers, shafts, seals, and other parts. Precautions are outlined regarding cleanliness and lubrication. Required tools are listed. The assembly procedure then provides mirrored instructions for reassembling the final drive unit.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjkskedmme
The document provides instructions for disassembling a final drive component from an excavator. It lists the required tools and gives step-by-step instructions to remove the final drive housing, gears, shafts, seals, and other internal parts. Detailed illustrations accompany each step. Disassembly involves removing retaining rings, gears, shafts, bearings, seals, and other parts from the housing using various tools, with attention to cleanliness and proper part labeling.
Caterpillar cat 325 c l excavator (prefix jld) service repair manual (jld0000...fjskeazqkkdmme
This document provides instructions for disassembling and assembling the final drive on 325C and 325C L excavator models. It gives detailed steps for removing the final drive from the machine, disassembling the internal components, and assembling the components back into the final drive housing. The procedures involve removing retaining rings, gears, shafts, seals, and other parts. Special tools are required and cleanliness is important when disassembling and assembling. Weights of removed parts are provided to assist with lifting.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...pwg56547003
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336D2 L Excavator (Prefix HBH) Service Repair Manual (HBH0000...pwg56547003
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It details 27 steps to remove over 50 individual parts, placing components in order and marking locations for reassembly.
3) Special care is required when removing parts under spring pressure or that could fall, and clean-up of fluids is important.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual (GJA0000...pwg56547003
1) The document provides step-by-step instructions to disassemble a travel motor from an excavator model 336D2 L.
2) Over 25 steps are outlined to remove components such as the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates.
3) Tools and safety precautions are listed for tasks like removing components under spring pressure.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...pwg56547003
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on an excavator. The disassembly process involves removing 30 individual parts in 11 steps, taking care with any parts under spring tension. The assembly follows the reverse of disassembly and involves positioning and installing 30 parts in 28 steps, ensuring proper bearing end play and lubrication.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...pwg56547003
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps to disassemble components such as the head, springs, seals, plates, and piston. It then lists 19 steps to reassemble these components and install new seals and O-rings, ensuring proper alignment of parts and applying thread lock compounds. Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolts. Cleanliness is emphasized throughout assembly and replacement of all worn parts.
Caterpillar Cat 336D L Excavator (Prefix MPL) Service Repair Manual (MPL00001...pwg56547003
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...pwg56547003
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual (L5X00001...pwg56547003
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are provided to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...pwg56547003
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components like gears, seals, springs and housings. The assembly procedure reverses the disassembly process in 22 steps and provides torque specifications for reinstalling components. Tools required include lifting devices, pry bars, driver groups and torque wrenches.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...pwg56547003
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled fan motor assembly back in place.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual (DTS00001...pwg56547003
This document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L excavator. The disassembly procedure involves removing over 30 individual parts in sequenced steps. The assembly procedure instructs putting the parts back together in reverse order and adjusting clearances as needed. Cleaning and inspecting parts is emphasized for proper reassembly.
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled piston motor back onto the fan motor assembly.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...pwg56547003
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts and lifting devices to extract the cover and internal gears and shafts.
3. Using tools like retaining ring pliers to detach components like carrier assemblies.
4. Pressing shafts from carriers and disassembling carriers by removing pins, washers and gears.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...pwg56547003
This document provides instructions for removing and installing camshafts on a Caterpillar C7 engine. The summary is:
1. The procedure begins by removing components like the vibration damper, pulley, rocker arms and pushrods.
2. Tools like timing pins and a puller are required to remove the camshaft.
3. The camshaft is removed by inserting timing pins, applying the puller, and removing camshaft bolts.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...pwg56547003
This document provides assembly instructions for a final drive in 3 steps:
1. Clean all parts thoroughly before assembly and inspect for wear or damage.
2. Apply specified tools, compounds, and brackets to assemble components like bearings, gears, seals and housings.
3. Measure clearances and torque bolts to specified values to correctly assemble and install the final drive. Cleanliness, compound application and torque specifications are critical to the assembly process.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...pwg56547003
The document provides instructions for disassembling the final drive of a 325D L excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Individual parts are to be disassembled from larger assemblies using hammers, punches, and presses. Cleanliness is important to prevent dirt from entering mechanisms during disassembly.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...pwg56547003
This document provides the disassembly and assembly procedures for a 325D L excavator travel motor. The key steps include:
1. Removing 28 components from the travel motor housing in a specific order using various tools.
2. Cleaning all parts thoroughly before assembly.
3. Assembling the travel motor in reverse order, replacing all seals and applying thread lock compound, noting part markings and orientations.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...pwg56547003
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, vibration damper and pulley, and crankshaft front seal. The procedures include using various tools to remove bolts, drilling holes, lifting components, and applying sealant.
2) Removing the flywheel requires attaching lifting tools, removing bolts, and removing the flywheel. Installing requires positioning, bolting, and checking runout.
3) Similar step-by-step processes are provided for the other components following safety notices to keep parts clean and contain fluids.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual (GJA0000...pwg56547003
1) The document provides step-by-step instructions to disassemble a travel motor from an excavator model 336D2 L.
2) Over 25 steps are outlined to remove components such as the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates.
3) Tools and safety precautions are listed for tasks like removing components under spring pressure.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...pwg56547003
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on an excavator. The disassembly process involves removing 30 individual parts in 11 steps, taking care with any parts under spring tension. The assembly follows the reverse of disassembly and involves positioning and installing 30 parts in 28 steps, ensuring proper bearing end play and lubrication.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...pwg56547003
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps to disassemble components such as the head, springs, seals, plates, and piston. It then lists 19 steps to reassemble these components and install new seals and O-rings, ensuring proper alignment of parts and applying thread lock compounds. Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolts. Cleanliness is emphasized throughout assembly and replacement of all worn parts.
Caterpillar Cat 336D L Excavator (Prefix MPL) Service Repair Manual (MPL00001...pwg56547003
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual (LMG00001...pwg56547003
The document provides instructions for installing a swivel on an excavator. It describes:
1) Attaching lifting equipment to the swivel and positioning it. 2) Installing a boot, clamp, retainer and bolts to mount the swivel. 3) Connecting hydraulic hose assemblies and fittings. 4) Removing the vacuum cap to complete installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual (L5X00001...pwg56547003
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are provided to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...pwg56547003
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components like gears, seals, springs and housings. The assembly procedure reverses the disassembly process in 22 steps and provides torque specifications for reinstalling components. Tools required include lifting devices, pry bars, driver groups and torque wrenches.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...pwg56547003
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled fan motor assembly back in place.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001...pwg56547003
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual (DTS00001...pwg56547003
This document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L excavator. The disassembly procedure involves removing over 30 individual parts in sequenced steps. The assembly procedure instructs putting the parts back together in reverse order and adjusting clearances as needed. Cleaning and inspecting parts is emphasized for proper reassembly.
The document provides instructions for disassembling and assembling the piston pump of an excavator. It details 22 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then details 31 steps for assembly, including cleaning parts, installing bearings, seals, springs, and other components in the reverse order of disassembly. Safety warnings are provided to wear protective equipment when handling spring loaded parts.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled piston motor back onto the fan motor assembly.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...pwg56547003
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts and lifting devices to extract the cover and internal gears and shafts.
3. Using tools like retaining ring pliers to detach components like carrier assemblies.
4. Pressing shafts from carriers and disassembling carriers by removing pins, washers and gears.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...pwg56547003
This document provides instructions for removing and installing camshafts on a Caterpillar C7 engine. The summary is:
1. The procedure begins by removing components like the vibration damper, pulley, rocker arms and pushrods.
2. Tools like timing pins and a puller are required to remove the camshaft.
3. The camshaft is removed by inserting timing pins, applying the puller, and removing camshaft bolts.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...pwg56547003
This document provides assembly instructions for a final drive in 3 steps:
1. Clean all parts thoroughly before assembly and inspect for wear or damage.
2. Apply specified tools, compounds, and brackets to assemble components like bearings, gears, seals and housings.
3. Measure clearances and torque bolts to specified values to correctly assemble and install the final drive. Cleanliness, compound application and torque specifications are critical to the assembly process.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...pwg56547003
The document provides instructions for disassembling the final drive of a 325D L excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Individual parts are to be disassembled from larger assemblies using hammers, punches, and presses. Cleanliness is important to prevent dirt from entering mechanisms during disassembly.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...pwg56547003
This document provides the disassembly and assembly procedures for a 325D L excavator travel motor. The key steps include:
1. Removing 28 components from the travel motor housing in a specific order using various tools.
2. Cleaning all parts thoroughly before assembly.
3. Assembling the travel motor in reverse order, replacing all seals and applying thread lock compound, noting part markings and orientations.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...pwg56547003
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1) The flywheel, flywheel housing, crankshaft rear seal, vibration damper and pulley, and crankshaft front seal. The procedures include using various tools to remove bolts, drilling holes, lifting components, and applying sealant.
2) Removing the flywheel requires attaching lifting tools, removing bolts, and removing the flywheel. Installing requires positioning, bolting, and checking runout.
3) Similar step-by-step processes are provided for the other components following safety notices to keep parts clean and contain fluids.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 8 00:51:28 UTC+0800 2020
3/3
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i04758849
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure (227-6116)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
1/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
2/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg (70
lb).
Illustration 3 g00879362
5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2) .
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4) .
3/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 5 g00780428
7. Remove gear (8). Remove spacer (9) .
Illustration 6 g00780432
8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11) .
9. Repeat Step 8 for the remaining two gear assemblies.
4/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 7 g00781401
10. Remove retaining ring (14) .
Illustration 8 g00781407
11. Remove carrier assembly (15) .
Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15) .
5/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21) .
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24) .
17. Repeat Steps 16.a through 16.e for the other two planetary.
7/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 15 g00781529
18. Remove gear (25). Remove spacer (26) .
Illustration 16 g00781559
19. Remove carrier assembly (27) .
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27), as follows.
8/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28) .
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
22. Repeat Steps 21.a through 21.e for the other two planetary gears.
9/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 20 g00781730
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34) .
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B) .
10/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35) .
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35) .
11/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38) .
Illustration 27 g01147975
12/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36) .
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36) .
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 8 00:52:24 UTC+0800 2020
13/13
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR JLD
Configuration: 325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
325C Excavator Machine Systems
Media Number -RENR5367-11 Publication Date -01/01/2012 Date Updated -17/02/2017
i04758848
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure (227-6116)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D
194-3878 Spanner Wrench As 1
194-3884 Spacer 1
E 138-7574 Link Bracket 2
H 6V-7030 Micrometer Depth Gauge Group 1
J FT-2770 Leak Down Test Tool 1
K 1U-6396 O-Ring Assembly Compound 1
L 5P-3931 Anti-Seize Compound 1
M 1U-8846 Gasket Sealant 1
N 8T-0531 Duo-Cone Seal Installer As 1
P 5P-3931 Anti-Seize Compound 1
Q 240-1886 Drill Fixture Gp 1
R 9S-3263 Thread Lock Compound 1
1/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Note: Cleanliness is an important factor. Before assembly, clean all parts thoroughly in cleaning
fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. All disassembly and all assembly procedures must be
performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts covered and
protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring. Use Tooling (K) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Note: Some of the images that are in this procedure do not show the sprocket assembly that is
attached to the final drive housing. If necessary, the weights that are given include the weight of
the sprocket assembly.
Illustration 1 g01147975
1. Apply Tooling (P) to the outer diameter of the bearings.
2. Use a suitable press to Install bearings (40) and (41). Make sure that bearing (41) and
bearing (40) contact the counterbore in housing (36) .
3. Use Tooling (N) to install Duo-Cone seal (39B) .
2/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g01147981
4. Use Tooling (N) to install Duo-Cone seal (39A) onto housing (38).
Illustration 3 g01147930
5. Use Tooling (E) and a suitable lifting device to install housing (36) onto housing (38). The
weight of housing (36) is approximately 100 kg (220 lb).
6. Remove Tooling (E) from housing (36) .
3/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 4 g01147724
7. Install stopper plate (35). Do not tighten stopper plate assembly (35) at this time.
Note: Stopper plate (35) will secure housing (36) to housing (38) .
8. Install Tooling (E) and a suitable lifting device to housing (36). The combined weight of
housing assembly (36) and (38) is approximately 120 kg (265 lb). Install housing assembly
(36) and (38) in a suitable press.
9. Remove stopper plate (35) .
Illustration 5 g01147727
10. Assemble Tooling (D), as shown.
Illustration 6 g01147731
11. Install Tooling (D) into housing (36), as shown.
12. Apply a force of 4000 kg (8818 lb) to the top of Tooling (D). Rotate housing (36) in order to
seat the bearings.
13. Reduce the force on the top of Tooling (D) to 1000 kg (2205 lb).
4/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 7 g01147737
14. Use Tooling (H) to take a measurement in three locations. Average the three measurements
and record the average measurement as Dimension (W) .
15. Remove Tooling (D) .
16. Separate Tooling (D) .
Illustration 8 g01147743
17. Use a micrometer in order to measure the thickness at three locations of the spacer from
Tooling (D). Record the average measurement as Dimension (X) .
5/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 9 g01147742
18. Use a micrometer in order to measure the thickness at three locations of stopper plate (35).
Record the average measurement as Dimension (Y) .
19. Subtract Dimension (X) from Dimension (Y) and record this figure as Dimension (Z) .
Illustration 10 g01147724
20. Install stopper plate (35) onto housing (38). Do not tighten stopper plate (35) at this time.
Stopper plate (35) will secure the final drive assembly while the final drive assembly is
repositioned onto Tooling (A) .
21. Use Tooling (E) and a suitable lifting device to reposition the final drive assembly onto
Tooling (A). The combined weight of housing assembly (36) and (38) is approximately 120
kg (265 lb).
22. Secure the final drive assembly to Tooling (A) .
6/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 11 g01148004
23. Secure the spanner socket from Tooling (D) to stopper plate (35) .
24. In order to determine the final bearing preload, add Dimension (W) to Dimension (Z) and
record this figure as Dimension (V) .
25. Use Tooling (H) to measure the distance in three locations.
26. Tighten stopper plate (35) until the average of the measurements is equal to Dimension (V) .
27. Remove Tooling (D) .
Illustration 12 g01372092
28. Install Tooling (Q) and a suitable vacuum onto stopper plate (35) .
7/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 13 g01147789
29. Use a suitable drill and Tooling (Q) in order to drill a hole to the depth of 15 mm (0.6 inch)
in the stopper palte and in housing (38) .
Illustration 14 g01147796
30. Install dowel (37) .
Illustration 15 g01147650
8/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 31. Apply Tooling (R) on bolts (35A). Install plate (35B) and bolts (35A) .
32. Repeat Steps 28 through 31 for the opposite side of stopper plate (35) .
Illustration 16 g00781807
33. Install O-ring seal (34) on housing (36) .
Illustration 17 g00781730
34. Install gear (33) on housing (36).
9/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engine...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 18 g00781719
35. Assemble carrier assembly (27), as follows.
Illustration 19 g00781607
a. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
b. Install two bearings (31) in planetary gear (32) .
c. Install thrust washers (30) and planetary gear (32) in the carrier assembly.
d. Install planetary shaft (28) in the carrier assembly.
e. Align the split in spring pin (29) to the top or to the bottom. Make a stake mark on
each side of the spring pin hole in the carrier. Each stake mark should be
approximately 1.50 mm (0.059 inch) from the outside diameter of the spring pin hole.
10/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 20 g00903073
f. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
36. Repeat Steps 35.a through 35.e in order to install the other two planetary gears in the carrier.
Illustration 21 g00781559
37. Use two people to install carrier assembly (27) in gear (33). The weight of carrier assembly
(27) is approximately 38 kg (85 lb).
11/19
325C & 325C L Excavators JLD00001-UP (MACHINE) POWERED BY 3126 Engi...
2020/7/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...