This document provides instructions for removing and installing various components of a 325C excavator engine, including:
- Removing and installing the flywheel, using link brackets and guide studs.
- Removing the crankshaft rear seal using a drill bit, slide hammer, and distorter rings.
- Installing the crankshaft rear seal with a seal installer.
- Removing and installing the flywheel housing, which weighs approximately 32 kg. Link brackets and sealant are used.
- Removing the vibration damper and pulley by removing bolts and spacers.
Caterpillar cat 325 c excavator (prefix bkt) service repair manual (bkt00001 ...fjsekkdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, flywheel housing, crankshaft rear seal, vibration damper and pulley.
- Detailed steps and required tools are given for each procedure, with illustrations to identify the parts. Precautions are noted to keep parts clean and contain fluids properly.
The document provides instructions for removing and installing a flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and safety notices, then outlines the step-by-step removal and installation procedures which include removing bolts, using lifting brackets, cleaning parts, applying sealant, and installing bolts with thread lock compound.
This document provides instructions for removing and installing a flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and safety precautions and gives a step-by-step process that includes removing bolts and installing sealant. Proper installation of O-rings and cleaning surfaces are emphasized to prevent leaks. Flywheel removal and installation procedures are referenced.
The document provides instructions for removing and installing a flywheel housing on a 325C excavator. It describes:
1) Removing the flywheel first using link brackets as tooling.
2) Cleaning all parts to prevent contamination before removal to avoid wear and failure.
3) Removing bolts to separate the flywheel housing, being careful to contain any fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that require cleaning surfaces and applying sealant or threadlocker to fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precautions are provided to keep parts clean and use threadlock compounds.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that require cleaning surfaces and applying sealant or threadlocker to fasteners.
Caterpillar cat 325 c excavator (prefix bkt) service repair manual (bkt00001 ...fjsekkdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, flywheel housing, crankshaft rear seal, vibration damper and pulley.
- Detailed steps and required tools are given for each procedure, with illustrations to identify the parts. Precautions are noted to keep parts clean and contain fluids properly.
The document provides instructions for removing and installing a flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and safety notices, then outlines the step-by-step removal and installation procedures which include removing bolts, using lifting brackets, cleaning parts, applying sealant, and installing bolts with thread lock compound.
This document provides instructions for removing and installing a flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and safety precautions and gives a step-by-step process that includes removing bolts and installing sealant. Proper installation of O-rings and cleaning surfaces are emphasized to prevent leaks. Flywheel removal and installation procedures are referenced.
The document provides instructions for removing and installing a flywheel housing on a 325C excavator. It describes:
1) Removing the flywheel first using link brackets as tooling.
2) Cleaning all parts to prevent contamination before removal to avoid wear and failure.
3) Removing bolts to separate the flywheel housing, being careful to contain any fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that require cleaning surfaces and applying sealant or threadlocker to fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precautions are provided to keep parts clean and use threadlock compounds.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that require cleaning surfaces and applying sealant or threadlocker to fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing a flywheel housing on a 325C excavator with a 3126B engine. It describes:
1) Removing the flywheel first, then bolts securing the housing to the cylinder block.
2) Lifting the housing off using link brackets and a lifting device due to its weight.
3) Cleaning and applying sealant to the housing and block face before installation.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing the vibration damper and pulley, flywheel housing, and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that require cleaning surfaces and applying sealant or threadlocker to fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...idkkdkmdm
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing the vibration damper and pulley, flywheel housing, and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, and installing the new seal with a seal installer tool.
- Removing and installing the flywheel housing which connects to the cylinder block, requiring cleaning of surfaces and use of a sealant and lifting tools.
- Removing the vibration damper and pulley from the crankshaft by removing bolts and spacers.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...jfjskekdhnejd
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for a crankshaft rear seal carrier, vibration damper, pulley, and flywheel housing that require cleaning surfaces and applying threadlock compounds.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...cdfzxs
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing the flywheel housing, vibration damper, and other components. Precise tools and cleaning of parts is emphasized to prevent contamination.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...fjsekkdmme
This document provides instructions for removing and installing various components of a 325C excavator engine, including:
- The flywheel, using link brackets and guide studs.
- The crankshaft rear seal, using a drill bit, slide hammer, and distorter rings.
- The crankshaft rear seal carrier, which is removed after removing the flywheel housing.
- The flywheel housing, which is fastened using link brackets before removal.
Precautions are provided to keep parts clean and contain fluids during disassembly and reassembly. Required tools are listed for each procedure.
This document provides instructions for removing and installing a flywheel, vibration damper, pulley, crankshaft rear seal, and flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and multi-step procedures for each component, including removing bolts, installing slide hammers, drilling holes, applying sealant, and checking runout after installation. Safety notices are included to keep parts clean and contain fluids properly.
This document provides instructions for removing and installing a flywheel, vibration damper, pulley, crankshaft rear seal, and flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and multi-step procedures for each component, including removing bolts, installing slide hammers, drilling holes, applying sealant, and checking runout after installation. Safety notices are included to keep parts clean and contain fluids properly.
The document provides instructions for removing and installing a flywheel housing on a 325C excavator. It details the required tools and safety notices, and outlines a multi-step procedure that includes removing bolts, taking care not to contaminate parts, and ensuring fluids are contained. Removal involves installing link brackets before taking off the remaining bolts and housing. Installation requires cleaning surfaces, applying sealant and thread lock compound, and torquing bolts to specification.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
More Related Content
Similar to Caterpillar Cat 325C EXCAVATOR (Prefix BKT) Service Repair Manual (BKT00001 and up).pdf
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing a flywheel housing on a 325C excavator with a 3126B engine. It describes:
1) Removing the flywheel first, then bolts securing the housing to the cylinder block.
2) Lifting the housing off using link brackets and a lifting device due to its weight.
3) Cleaning and applying sealant to the housing and block face before installation.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing the vibration damper and pulley, flywheel housing, and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that require cleaning surfaces and applying sealant or threadlocker to fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...idkkdkmdm
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing the vibration damper and pulley, flywheel housing, and rear seal carrier. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, and installing the new seal with a seal installer tool.
- Removing and installing the flywheel housing which connects to the cylinder block, requiring cleaning of surfaces and use of a sealant and lifting tools.
- Removing the vibration damper and pulley from the crankshaft by removing bolts and spacers.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...jfjskekdhnejd
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for a crankshaft rear seal carrier, vibration damper, pulley, and flywheel housing that require cleaning surfaces and applying threadlock compounds.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...cdfzxs
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing the flywheel housing, vibration damper, and other components. Precise tools and cleaning of parts is emphasized to prevent contamination.
Caterpillar cat 325 c excavator (prefix bla) service repair manual (bla00001 ...fjsekkdmme
This document provides instructions for removing and installing various components of a 325C excavator engine, including:
- The flywheel, using link brackets and guide studs.
- The crankshaft rear seal, using a drill bit, slide hammer, and distorter rings.
- The crankshaft rear seal carrier, which is removed after removing the flywheel housing.
- The flywheel housing, which is fastened using link brackets before removal.
Precautions are provided to keep parts clean and contain fluids during disassembly and reassembly. Required tools are listed for each procedure.
This document provides instructions for removing and installing a flywheel, vibration damper, pulley, crankshaft rear seal, and flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and multi-step procedures for each component, including removing bolts, installing slide hammers, drilling holes, applying sealant, and checking runout after installation. Safety notices are included to keep parts clean and contain fluids properly.
This document provides instructions for removing and installing a flywheel, vibration damper, pulley, crankshaft rear seal, and flywheel housing on a 325C excavator with a 3126B engine. It describes the required tools and multi-step procedures for each component, including removing bolts, installing slide hammers, drilling holes, applying sealant, and checking runout after installation. Safety notices are included to keep parts clean and contain fluids properly.
The document provides instructions for removing and installing a flywheel housing on a 325C excavator. It details the required tools and safety notices, and outlines a multi-step procedure that includes removing bolts, taking care not to contaminate parts, and ensuring fluids are contained. Removal involves installing link brackets before taking off the remaining bolts and housing. Installation requires cleaning surfaces, applying sealant and thread lock compound, and torquing bolts to specification.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjjsekkdmme
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. The flywheel removal procedure involves using link brackets and forcing bolts to lift the flywheel off the crankshaft. The crankshaft pulley is removed using a combination puller tool. Both components are installed by reversing the removal process and tightening to the specified torques.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Similar to Caterpillar Cat 325C EXCAVATOR (Prefix BKT) Service Repair Manual (BKT00001 and up).pdf (18)
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
A Guide to a Winning Interview June 2024Bruce Bennett
This webinar is an in-depth review of the interview process. Preparation is a key element to acing an interview. Learn the best approaches from the initial phone screen to the face-to-face meeting with the hiring manager. You will hear great answers to several standard questions, including the dreaded “Tell Me About Yourself”.
Success is often not achievable without facing and overcoming obstacles along the way. To reach our goals and achieve success, it is important to understand and resolve the obstacles that come in our way.
In this article, we will discuss the various obstacles that hinder success, strategies to overcome them, and examples of individuals who have successfully surmounted their obstacles.
Learnings from Successful Jobs SearchersBruce Bennett
Are you interested to know what actions help in a job search? This webinar is the summary of several individuals who discussed their job search journey for others to follow. You will learn there are common actions that helped them succeed in their quest for gainful employment.
Joyce M Sullivan, Founder & CEO of SocMediaFin, Inc. shares her "Five Questions - The Story of You", "Reflections - What Matters to You?" and "The Three Circle Exercise" to guide those evaluating what their next move may be in their careers.
In the intricate tapestry of life, connections serve as the vibrant threads that weave together opportunities, experiences, and growth. Whether in personal or professional spheres, the ability to forge meaningful connections opens doors to a multitude of possibilities, propelling individuals toward success and fulfillment.
Eirini is an HR professional with strong passion for technology and semiconductors industry in particular. She started her career as a software recruiter in 2012, and developed an interest for business development, talent enablement and innovation which later got her setting up the concept of Software Community Management in ASML, and to Developer Relations today. She holds a bachelor degree in Lifelong Learning and an MBA specialised in Strategic Human Resources Management. She is a world citizen, having grown up in Greece, she studied and kickstarted her career in The Netherlands and can currently be found in Santa Clara, CA.
We recently hosted the much-anticipated Community Skill Builders Workshop during our June online meeting. This event was a culmination of six months of listening to your feedback and crafting solutions to better support your PMI journey. Here’s a look back at what happened and the exciting developments that emerged from our collaborative efforts.
A Gathering of Minds
We were thrilled to see a diverse group of attendees, including local certified PMI trainers and both new and experienced members eager to contribute their perspectives. The workshop was structured into three dynamic discussion sessions, each led by our dedicated membership advocates.
Key Takeaways and Future Directions
The insights and feedback gathered from these discussions were invaluable. Here are some of the key takeaways and the steps we are taking to address them:
• Enhanced Resource Accessibility: We are working on a new, user-friendly resource page that will make it easier for members to access training materials and real-world application guides.
• Structured Mentorship Program: Plans are underway to launch a mentorship program that will connect members with experienced professionals for guidance and support.
• Increased Networking Opportunities: Expect to see more frequent and varied networking events, both virtual and in-person, to help you build connections and foster a sense of community.
Moving Forward
We are committed to turning your feedback into actionable solutions that enhance your PMI journey. This workshop was just the beginning. By actively participating and sharing your experiences, you have helped shape the future of our Chapter’s offerings.
Thank you to everyone who attended and contributed to the success of the Community Skill Builders Workshop. Your engagement and enthusiasm are what make our Chapter strong and vibrant. Stay tuned for updates on the new initiatives and opportunities to get involved. Together, we are building a community that supports and empowers each other on our PMI journeys.
Stay connected, stay engaged, and let’s continue to grow together!
About PMI Silver Spring Chapter
We are a branch of the Project Management Institute. We offer a platform for project management professionals in Silver Spring, MD, and the DC/Baltimore metro area. Monthly meetings facilitate networking, knowledge sharing, and professional development. For more, visit pmissc.org.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01980480
Flywheel - Remove and Install
SMCS - 1156-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B FT2712 Guide Stud 2
1/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01026562
1. Install Tooling (A) on the flywheel. Fasten a suitable lifting device to the flywheel. The
weight of flywheel (1) is approximately 23 kg (50 lb).
2. Remove two bolts and install Tooling (B). Remove the remaining bolts.
3. Remove flywheel (1).
4. Place the flywheel on a wood block. Use a hammer and a punch in order to remove the
flywheel ring gear.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B FT2712 Guide Stud 2
C 9S-3263 Thread Lock Compound 1
2/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01026562
1. Raise the temperature of the flywheel ring gear. Do not use a torch to heat the flywheel ring
gear. Position the flywheel ring gear on the flywheel with the part number toward the
crankshaft.
2. Use a suitable lifting device to position flywheel (1) on Tooling (B). The weight of flywheel
(1) is approximately 23 kg (50 lb).
3. Apply Tooling (C) to the threads of the bolts. Install the bolts. Remove Tooling (B) and
install the remaining bolts.
4. Tighten the bolts evenly to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
5. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:47:07 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01980554
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller Gp 1
C 4C-4869 Distorter Ring 1
D 5P-7312 Seal Distorter 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to drill three evenly spaced holes in the crankshaft rear seal.
1/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00989088
2. Carefully remove crankshaft rear seal (1) by alternating the position of Tooling (B) from
hole to hole. This will allow crankshaft rear seal (1) to be removed evenly without damage
to the rear flange surface of the crankshaft.
Note: New engines from the factory do not have a wear sleeve. Engines with seals that have
been replaced will be equipped with a wear sleeve. If the crankshaft of the engine is
equipped with a wear sleeve, refer to Disassembly and Assembly, "Crankshaft Wear Sleeve
(Rear) - Remove" in order to remove the wear sleeve.
3. Use Tooling (C) and Tooling (D) to remove the wear sleeve (if equipped).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:48:03 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01980581
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
E 1U-7598 Seal Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Replacement rear seals are supplied with a wear sleeve. This wear sleeve must be installed
with the rear seal. New engines from the factory do not have a wear sleeve. Do not install the rear
seal if any of the following conditions exist:
• The crankshaft rear seal has been separated from the wear sleeve.
• The rear seal group appears to be damaged.
• The crankshaft rear seal has been lubricated. The seal is designed to be installed dry.
1. Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of
the crankshaft rear seal.
1/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01026625
Typical example
2. Use Tooling (E) to install crankshaft rear seal (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:48:59 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01987820
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
Start By:
a. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01027007
1. Remove bolts (1).
2. Remove rear seal carrier (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-8440 Component Cleaner
B 169-5464 Quick Cure Primer
C 1U-8846 Gasket Sealant
D 9S-3263 Thread Lock Compound
NOTICE
Keep all parts clean from contaminants.
2/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01027007
1. Clean the joint face of rear seal carrier (2) and the cylinder block with Tooling (A).
2. Apply Tooling (B) to the joint face of rear seal carrier (2). Allow the primer to air dry for
three to five minutes.
Note: Tooling (C) is used on the joint face of rear seal carrier (2). Do not allow the sealant
to get into the oil passage in the mounting face of the cylinder block.
3. Apply Tooling (C) to the joint face of rear seal carrier (2). Spread the sealant uniformly.
Rear seal carrier (2) must be installed within ten minutes of application of the sealant.
4. Position rear seal carrier (2) on the dowels in the rear of the cylinder block.
5. Apply Tooling (D) on the threads of bolts (1). Install bolts (1) that hold rear seal carrier (2)
to the cylinder block.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
3/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i04855211
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01011885
1. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1).
2. Remove bolts (2) and bolt (3) that fastens flywheel housing (1) to the cylinder block.
3. Remove flywheel housing (1). The weight of flywheel housing (1) is approximately 32 kg
(70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 1U-8846 Gasket Sealant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g00740507
Correct installation of O-ring seal (3). Do not install the O-ring seal in location (4).
Note: On wet flywheel housings that have rear seal carriers, ensure that the O-ring seal (3)
is installed properly. Improper installation will result in leakage of torque converter oil
between the flywheel housing and the cylinder block.
Note: Ensure that the mating surface of the flywheel housing and the mounting face of the
cylinder block are thoroughly clean.
1. Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
Illustration 3 g01011885
3/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 2. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). Position flywheel
housing (1) on the cylinder block. The weight of flywheel housing (1) is approximately
32 kg (70 lb).
3. Install bolts (2) and bolt (3) that fastens flywheel housing (1) to the cylinder block.
4. Remove Tooling (A) and the hoist from flywheel housing (1).
5. Check the flywheel housing runout. Refer to the Systems Operation/Testing and Adjusting,
"Flywheel and Flywheel Housing".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:50:50 UTC+0800 2020
4/4
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02370081
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Illustration 1 g00612677
1. Remove bolts (2), crankshaft vibration damper (1), and the spacers from the crankshaft
pulley.
1/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g00612684
2. Remove belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
3. Remove bolts (4).
4. Remove crankshaft pulley (5).
Installation Procedure
Illustration 3 g00612684
1. Position crankshaft pulley (5) on the crankshaft. Install bolts (4) and tighten the bolts to a
torque of 160 ± 30 N·m (118 ± 22 lb ft).
2. Install belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
Note: Check the alignment marks on the rubber vibration dampers for proper alignment.
The rubber vibration damper should be replaced if the rubber vibration damper is out of
alignment. Refer to Specifications, "Vibration Damper".
2/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g00612677
3. Install the spacers and crankshaft vibration damper (1). Install bolts (2) and tighten to a
torque of 55 ± 10 N·m (40 ± 7 lb ft).
4. Adjust the tension of the belt. Refer to Specifications, "Belt Tension Chart".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:51:46 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982085
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00989224
1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:52:42 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982092
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00989228
1. Use Tooling (C) to install crankshaft front seal (1).
Note: The crankshaft seal is designed to be installed dry.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:53:38 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379367
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00728351
1. Remove four bolts (1) that fasten bracket (2) on the front of the engine.
Illustration 2 g00728369
2. Remove the bolts (3) and front cover (4) from the front housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:54:33 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379400
Front Cover - Install
SMCS - 1166-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The rear face of the cover and the front face of the housing must be clean.
1. Inspect the condition of the housing cover gasket. Replace the gasket, if necessary.
1/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00728369
2. Install the housing cover gasket.
3. Position front cover (4) on the front housing. Install the bolts (3) on front cover (4).
Illustration 2 g00728351
4. Position bracket (2) on the front of the engine.
5. Install four bolts (1) that fasten bracket (2) on the engine.
End By:
a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:55:29 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983906
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.