This document provides instructions for removing and installing inlet and exhaust valves and valve guides on Caterpillar 325, 325L, and 325LN excavator models. It includes the required tools and multi-step procedures for both removal and installation. Safety notices are provided to keep parts clean and contain fluids. References are also included for determining if valves and guides can be reused.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...f8usiejdkmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using specific tools to compress springs, extract components, and install replacements. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325-A, 325, 325 L AND 325 LN EXCAVATOR (Prefix 9ZK) Service R...yan77xunhao
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 9 zk) service repair manual (9zk00001...ifoseidkkd
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...f8usiejdkmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using specific tools to compress springs, extract components, and install replacements. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325-A, 325, 325 L AND 325 LN EXCAVATOR (Prefix 9ZK) Service R...yan77xunhao
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 9 zk) service repair manual (9zk00001...ifoseidkkd
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
The document provides instructions for removing and installing various engine components on Caterpillar 336D2 excavators, including:
1) Removing and installing the engine oil filter and oil filter base.
2) Removing and installing the engine oil cooler.
3) Removing and installing the air cleaner assembly.
4) Removing and installing the turbocharger.
5) Removing and installing the water temperature regulator.
Detailed steps and illustrations are provided for each procedure.
This document provides instructions for disassembling a travel motor. It lists 27 steps to remove parts like the head, springs, pistons, bearings and seals. Tools required include bolts, nuts, retaining ring pliers, a bearing puller, and various adapters and eyebolts for safely removing parts with spring tension. Detailed illustrations accompany each step to ensure correct part identification and procedure. Safety notices warn of potential for parts propelled by springs and instruct wearing protective equipment.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...fuusejkddmmd3e
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
Caterpillar Cat 336D L Excavator (Prefix M3N) Service Repair Manual (M3N00001...fuusejkddmmd3e
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. It describes cleaning grease from the swing gear and bearing, marking them for alignment during reinstallation, attaching lifting tools, using a hydraulic torque wrench to remove bolts and spacers, and lifting out the swing gear and bearing assembly which weighs approximately 280 kg. Cleaning and inspection of parts is recommended before reassembly.
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
The document provides instructions for disassembling a 330F LN excavator travel motor. It lists 28 steps to completely disassemble the travel motor, removing components like the head, housing assembly, brake piston, friction discs, and pistons. Detailed illustrations accompany each step to show how to remove parts and what tools are required. Safety notices are included throughout to warn of spring forces, pressurized air, and other hazards during disassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly involves installing the parts in reverse order and adjusting the bearing preload using shims to achieve the proper clearance. Special tools and techniques like applying threadlocker and leak testing are required to properly reassemble the final drive.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure instructs putting the final drive back together in reverse order and adjusting the bearing preload using shims to achieve the proper clearance.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to align the front cover and tighten bolts.
4. Install a new front seal, crankshaft pulley, and fan if equipped.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...fuusejkddmmd3e
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...fuusejkddmmd3e
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...fuusejkddmmd3e
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly procedure then consists of 27 steps to dismantle the various components of the travel motor, including removing the head, brake piston, barrel assembly, cam plate, and other internal parts. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care when handling components and contain any fluids.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fuusejkddmmd3e
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fuusejkddmmd3e
This document provides disassembly instructions for a final drive on an excavator. It begins by having the technician mark the final drive for alignment and then remove the final drive and travel motor. Over 30 steps are then outlined to disassemble the various components of the final drive. This includes removing gears, carriers, shafts, seals and other parts using specialized tools. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fuusejkddmmd3e
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The document provides instructions for removing and installing various engine components on Caterpillar 336D2 excavators, including:
1) Removing and installing the engine oil filter and oil filter base.
2) Removing and installing the engine oil cooler.
3) Removing and installing the air cleaner assembly.
4) Removing and installing the turbocharger.
5) Removing and installing the water temperature regulator.
Detailed steps and illustrations are provided for each procedure.
This document provides instructions for disassembling a travel motor. It lists 27 steps to remove parts like the head, springs, pistons, bearings and seals. Tools required include bolts, nuts, retaining ring pliers, a bearing puller, and various adapters and eyebolts for safely removing parts with spring tension. Detailed illustrations accompany each step to ensure correct part identification and procedure. Safety notices warn of potential for parts propelled by springs and instruct wearing protective equipment.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...fuusejkddmmd3e
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
Caterpillar Cat 336D L Excavator (Prefix M3N) Service Repair Manual (M3N00001...fuusejkddmmd3e
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. It describes cleaning grease from the swing gear and bearing, marking them for alignment during reinstallation, attaching lifting tools, using a hydraulic torque wrench to remove bolts and spacers, and lifting out the swing gear and bearing assembly which weighs approximately 280 kg. Cleaning and inspection of parts is recommended before reassembly.
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
The document provides instructions for disassembling a 330F LN excavator travel motor. It lists 28 steps to completely disassemble the travel motor, removing components like the head, housing assembly, brake piston, friction discs, and pistons. Detailed illustrations accompany each step to show how to remove parts and what tools are required. Safety notices are included throughout to warn of spring forces, pressurized air, and other hazards during disassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly involves installing the parts in reverse order and adjusting the bearing preload using shims to achieve the proper clearance. Special tools and techniques like applying threadlocker and leak testing are required to properly reassemble the final drive.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure instructs putting the final drive back together in reverse order and adjusting the bearing preload using shims to achieve the proper clearance.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to align the front cover and tighten bolts.
4. Install a new front seal, crankshaft pulley, and fan if equipped.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...fuusejkddmmd3e
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...fuusejkddmmd3e
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...fuusejkddmmd3e
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly procedure then consists of 27 steps to dismantle the various components of the travel motor, including removing the head, brake piston, barrel assembly, cam plate, and other internal parts. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care when handling components and contain any fluids.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fuusejkddmmd3e
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fuusejkddmmd3e
This document provides disassembly instructions for a final drive on an excavator. It begins by having the technician mark the final drive for alignment and then remove the final drive and travel motor. Over 30 steps are then outlined to disassemble the various components of the final drive. This includes removing gears, carriers, shafts, seals and other parts using specialized tools. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fuusejkddmmd3e
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:17:22 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:18:18 UTC+0800 2020
5/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:19:14 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:20:10 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:21:05 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:22:01 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:22:57 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...