This document provides instructions for servicing the travel motor on a 324E L Excavator. It outlines 28 steps to disassemble the travel motor, including removing the head, brake piston, rotating assembly, and various seals and bearings. It then lists 13 steps for reassembling the travel motor, including installing seals, piston actuator, retaining rings, and adjusting bearing races on the shaft. Various tools are required to complete the disassembly and assembly processes.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...paws21610697
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and presents 28 steps to take the travel motor apart and put it back together. The steps include removing components like the head, brake piston, barrel assembly parts, and seals and installing them in reverse order. Cautions are provided about spring force and ensuring proper alignment of parts.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torques. Key steps include removing and installing retaining rings, seals, bearings and repositioning marked components in their original locations.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...paws21610697
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and presents 28 steps to take the travel motor apart and put it back together. The steps include removing components like the head, brake piston, barrel assembly parts, and seals and installing them in reverse order. Cautions are provided about spring force and ensuring proper alignment of parts.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torques. Key steps include removing and installing retaining rings, seals, bearings and repositioning marked components in their original locations.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 324 e l excavator (prefix jcz) service repair manual (jcz0000...fhhsjdkmem
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly is the reverse of the disassembly with instructions to lubricate parts, align markings and install components in the correct orientation using various tools. Proper assembly is important to prevent damage and ensure correct functioning of the travel motor.
Caterpillar cat 324 e excavator (prefix jcz) service repair manual (jcz00001 ...fhhsjdkmem
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly is the reverse of the disassembly with instructions to lubricate parts, align markings and install components in the correct orientation using various tools. Proper assembly is important to prevent damage and ensure correct functioning of the travel motor.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...jdkskmdmdm
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Proper assembly requires the use of several specialized tools to press components and install retaining rings. Cautions are provided regarding spring loaded parts and ensuring marks are aligned during reassembly.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...kubei069369925
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process is the reverse and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...f8uesjdkdmdm
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Proper assembly requires the use of several specialized tools to press components and install retaining rings. Cautions are provided regarding spring loaded parts and ensuring marks are aligned during reassembly.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...prmy389342
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys. Special tools are required for tasks like removing retaining rings and installing seals.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...8ufjsekddm8u
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly is the reverse of the disassembly with instructions to lubricate parts, align markings and install components in the correct orientation using various tools. Proper assembly is important to prevent damage and ensure correct functioning of the travel motor.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process is described in 27 steps and involves removing components like the motor head, brake piston, rotating assembly, seals, and bearings. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools required include retaining ring pliers, drivers, pullers, and press equipment. Cautions are provided about spring loading and containing fluids during repair work.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...shanruliu7360
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs, seals and bearings. The assembly section outlines putting the travel motor back together in the reverse order and notes the proper installation of components and use of retaining rings, seals and alignment marks. Tools required include retaining ring pliers, drivers, pullers and press equipment.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step procedure includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process is described in 27 steps and involves removing components like the motor head, brake piston, rotating assembly, seals, and bearings. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools required include retaining ring pliers, drivers, pullers, and press equipment. Cautions are provided about spring loading and containing fluids during repair work.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step procedure includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
DAEWOO DOOSAN MEGA 160TC TIER-II WHEEL LOADER Parts Catalogue Manual.pdfjfkskmmdmdm
The document provides a parts list and diagrams for components of a MEGA 160TC TIER-II engine. It includes lists of cylinder block, timing gear case, flywheel housing, crankshaft, and cylinder head parts with part numbers, descriptions, quantities, serial numbers and replacement part information. The parts are identified by key numbers on diagrams of each engine component.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
This document provides instructions for disassembling and assembling the final drive of an excavator. The key steps include:
1. Removing the final drive assembly and disassembling its internal components like gears, shafts, and housings.
2. Cleaning all parts thoroughly before assembly to prevent dirt from entering mechanisms.
3. Assembling the components in reverse order and ensuring proper installation of seals and bearings, applying anti-seize compound as needed.
4. Using tools like a press and micrometer to set the bearing preload and determine the correct shim thickness.
More Related Content
Similar to Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual (PNW00001 and up).pdf
Caterpillar cat 324 e l excavator (prefix jcz) service repair manual (jcz0000...fhhsjdkmem
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly is the reverse of the disassembly with instructions to lubricate parts, align markings and install components in the correct orientation using various tools. Proper assembly is important to prevent damage and ensure correct functioning of the travel motor.
Caterpillar cat 324 e excavator (prefix jcz) service repair manual (jcz00001 ...fhhsjdkmem
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly is the reverse of the disassembly with instructions to lubricate parts, align markings and install components in the correct orientation using various tools. Proper assembly is important to prevent damage and ensure correct functioning of the travel motor.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...jdkskmdmdm
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Proper assembly requires the use of several specialized tools to press components and install retaining rings. Cautions are provided regarding spring loaded parts and ensuring marks are aligned during reassembly.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...kubei069369925
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process is the reverse and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys and piston marks. Special tools are required for tasks like removing races and seals.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...f8uesjdkdmdm
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Proper assembly requires the use of several specialized tools to press components and install retaining rings. Cautions are provided regarding spring loaded parts and ensuring marks are aligned during reassembly.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...prmy389342
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys. Special tools are required for tasks like removing retaining rings and installing seals.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual (JCZ00001...8ufjsekddm8u
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process involves removing 28 components from the travel motor including the head, brake piston, plates, springs and seals. The assembly is the reverse of the disassembly with instructions to lubricate parts, align markings and install components in the correct orientation using various tools. Proper assembly is important to prevent damage and ensure correct functioning of the travel motor.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process is described in 27 steps and involves removing components like the motor head, brake piston, rotating assembly, seals, and bearings. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools required include retaining ring pliers, drivers, pullers, and press equipment. Cautions are provided about spring loading and containing fluids during repair work.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...shanruliu7360
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs, seals and bearings. The assembly section outlines putting the travel motor back together in the reverse order and notes the proper installation of components and use of retaining rings, seals and alignment marks. Tools required include retaining ring pliers, drivers, pullers and press equipment.
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process includes removing 28 components from the travel motor housing including the head, brake piston, plates, springs and seals. The assembly section outlines 29 steps to reinstall these components in reverse order using various tools. Special care must be taken when working with pressurized components or parts under spring force.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step procedure includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
Caterpillar Cat 324E L Excavator (Prefix JCZ) Service Repair Manual Instant D...rishang96299
This document provides instructions for disassembling and assembling the travel motor on 324E and 324E L excavator models. The disassembly process is described in 27 steps and involves removing components like the motor head, brake piston, rotating assembly, seals, and bearings. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools required include retaining ring pliers, drivers, pullers, and press equipment. Cautions are provided about spring loading and containing fluids during repair work.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step procedure includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
Similar to Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual (PNW00001 and up).pdf (19)
DAEWOO DOOSAN MEGA 160TC TIER-II WHEEL LOADER Parts Catalogue Manual.pdfjfkskmmdmdm
The document provides a parts list and diagrams for components of a MEGA 160TC TIER-II engine. It includes lists of cylinder block, timing gear case, flywheel housing, crankshaft, and cylinder head parts with part numbers, descriptions, quantities, serial numbers and replacement part information. The parts are identified by key numbers on diagrams of each engine component.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
This document provides instructions for disassembling and assembling the final drive of an excavator. The key steps include:
1. Removing the final drive assembly and disassembling its internal components like gears, shafts, and housings.
2. Cleaning all parts thoroughly before assembly to prevent dirt from entering mechanisms.
3. Assembling the components in reverse order and ensuring proper installation of seals and bearings, applying anti-seize compound as needed.
4. Using tools like a press and micrometer to set the bearing preload and determine the correct shim thickness.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325-A excavator engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening fasteners in a specific sequence using proper torque values. Required tools are listed for each job.
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...jfkskmmdmdm
The document provides disassembly and assembly instructions for the final drive of a 325B L excavator. It details 33 steps to disassemble the final drive components including removing carriers, gears, seals and bearings. It also outlines 28 steps for reassembling the final drive, including pressing in bearings, determining the correct shim thickness, installing seals and gears, and torquing bolts. Tools and torque specifications are provided. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the excavator's final drive system.
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...jfkskmmdmdm
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual...jfkskmmdmdm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 325-A excavator powered by a 3116 engine. It describes the required tools and gives step-by-step procedures and illustrations for removing the governor, installing a new governor, removing the fuel injection control linkage, and installing the fuel injection control linkage. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual...jfkskmmdmdm
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 325 and 325L excavators powered by 3116 engines. It describes the required tools and outlines the step-by-step procedures for removing and installing exhaust manifolds, removing inlet manifolds, and installing inlet manifolds. It also provides instructions for removing and installing inlet and exhaust valves from the cylinder head assembly.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmmdmdm
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, piston shoes, shaft assembly, seals, and other components. Special care must be taken to keep components in order and avoid damage during disassembly.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325 excavator engine. The removal procedure involves using a valve guide driver tool to push the guides out of the cylinder head from the intake/exhaust ports. For installation, new guides are lubricated and driven into the cylinder head with the driver tool. The instructions emphasize keeping parts clean to prevent wear and shortening component life.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmmdmdm
This document provides instructions for removing and installing an exhaust manifold and inlet and exhaust valves on a 325-A FM L EXCAVATOR 7LM. It describes:
1) Removing the bolts, exhaust manifold, and gaskets from the cylinder head to remove the exhaust manifold.
2) Installing new gaskets and mounting the exhaust manifold to the cylinder head, applying anti-seize compound and torqueing bolts.
3) Removing inlet and exhaust valves by compressing springs, removing retainers and springs, and removing seals and valves.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...jfkskmmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using specific tools to compress springs, extract components, and install replacement parts. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual (...jfkskmmdmdm
This service repair manual provides instructions for installing a governor on a Caterpillar 3116 engine that powers 325 and 325L excavators. It details cleaning and lubricating parts, placing seals and the governor in the cylinder head, installing clips and pins to connect components, and setting fuel settings using specialized tools. The document provides illustrations and numbered steps for the installation process and refers to other manuals for additional guidance.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual (...jfkskmmdmdm
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 325 and 325L excavators powered by 3116 engines. It describes the required tools and outlines the step-by-step procedures for removing components like bolts, studs, gaskets and manifolds. The installation section specifies applying anti-seize compound and sealer, installing new gaskets, bolts and manifolds, and tightening to the specified torques. It also includes warnings about keeping components clean and containing fluids.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325-A excavator engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening fasteners in a specific sequence using proper torque values. Required tools are listed for each job.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
2/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3), port plate (4), and bearing (5) .
3/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00887311
7. Remove O-ring seals (6). Remove springs (7) .
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
4/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
5/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00887401
Illustration 9 g00887405
12. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
6/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Remove shaft (15) from rotating assembly (16) .
Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
7/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00887463
17. Rotate shaft (15). Install shaft (15) into a suitable press. Install Tooling (E). Remove bearing
race (19) from shaft (15) .
Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
9/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
10/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 27 23:10:38 UTC+0800 2020
11/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324E L EXCAVATOR PNW
Configuration: 324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit Machine
Systems
Media Number -KENR9844-04 Publication Date -01/04/2015 Date Updated -14/04/2015
i04216229
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
2/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) in order to install
lip seal (28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (27) .
3/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 6 g02107975
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
4/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21) .
5/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g02107957
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5) .
Illustration 22 g00887295
10/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 177 ± 18 N·m (130.5 ± 13.27 lb ft).
End By: Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 27 23:11:38 UTC+0800 2020
11/11
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324E L EXCAVATOR PNW
Configuration: 324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit Machine
Systems
Media Number -KENR9844-04 Publication Date -01/04/2015 Date Updated -14/04/2015
i04216189
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00878123
2. Install new O-ring seal (6). Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4), as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 5. Carefully install travel motor (4) onto Tooling (A). Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3). Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 27 23:12:37 UTC+0800 2020
4/4
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324E L EXCAVATOR PNW
Configuration: 324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit Machine
Systems
Media Number -KENR9844-04 Publication Date -01/04/2015 Date Updated -14/04/2015
i04249066
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
B 138-7574 Link Bracket 2
C 154-6184 Forcing Bolt (M 20) 2
Start By:
A. Separate the track assembly. Refer to Disassembly and Assembly, "Track - Separate".
B. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/3
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 1 g00489826
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
2/3
324E L Excavator PNW00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP5...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...