This document provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing by removing bolts and support pieces.
- Removing and installing the camshaft idler gear by pressing out/in the bearing and aligning timing marks.
- Removing and installing the valve mechanism cover and base by removing/replacing bolts and reconnecting harnesses.
- Removing the rocker shaft and pushrods by loosening adjustment screws, removing bolts, and separating connecting pieces.
The document provides detailed step-by-step instructions accompanied by illustrations of each component for guidance on
Caterpillar cat 324 d l excavator (prefix dfp) service repair manual (dfp0000...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar cat 324 d l excavator (prefix dfp) service repair manual (dfp0000...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
This document provides instructions for removing and installing various engine components on a Caterpillar 735 articulated truck, including:
- Installing the rear power take-off using specific tools and torque specifications.
- Removing and installing the vibration damper and pulley using lifting devices and guide studs.
- Removing the crankshaft front seal using a slide hammer puller.
- Installing the new crankshaft front seal and wear sleeve using a seal locator, bolts, nut and seal installer.
Caterpillar cat 320 d l excavator (prefix klm) service repair manual (klm0000...fujsjefjwekskemm
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal. Technicians are advised to keep all parts clean and free of contaminants to prevent premature wear. The instructions are part of a service manual for Caterpillar 320D and 320D L excavators.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a C11 Industrial Engine HRA. The procedures describe using various tools to remove and install components in a specific sequence, and include notices about keeping parts clean and containing fluids.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...JayHaines2
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document contains illustrations and specifies any required tools. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d excavator (prefix dfp) service repair manual (dfp00001 ...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...shudun96087
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...qme229722
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...kesi7153062
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
This document provides instructions for removing and installing various engine components on a Caterpillar 735 articulated truck, including:
- Installing the rear power take-off using specific tools and torque specifications.
- Removing and installing the vibration damper and pulley using lifting devices and guide studs.
- Removing the crankshaft front seal using a slide hammer puller.
- Installing the new crankshaft front seal and wear sleeve using a seal locator, bolts, nut and seal installer.
Caterpillar cat 320 d l excavator (prefix klm) service repair manual (klm0000...fujsjefjwekskemm
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal. Technicians are advised to keep all parts clean and free of contaminants to prevent premature wear. The instructions are part of a service manual for Caterpillar 320D and 320D L excavators.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a C11 Industrial Engine HRA. The procedures describe using various tools to remove and install components in a specific sequence, and include notices about keeping parts clean and containing fluids.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...JayHaines2
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document contains illustrations and specifies any required tools. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d excavator (prefix dfp) service repair manual (dfp00001 ...fjskekdmmem
This document provides instructions for servicing components of a 324D and 324D L excavator powered by a C7 engine. It describes procedures for removing and installing components such as the front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft, and pushrods. The document emphasizes keeping parts clean and contains illustrations to support the text instructions.
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...shudun96087
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes procedures for removing and installing various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The manual emphasizes keeping components clean and applying sealant and primer as specified. Tools required are also listed for each procedure.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...qme229722
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...kesi7153062
This service repair manual provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing
- Removing and installing the camshaft idler gear
- Removing and installing the valve mechanism cover and valve mechanism cover base
- Removing the rocker shaft and pushrods
Detailed step-by-step instructions are provided for each procedure, along with illustrations to identify the specific components and torque specifications for fasteners. Technicians are advised to keep components clean and free of contaminants during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies any required tools for each procedure. Technicians are instructed to keep all parts clean and free of contaminants to prevent premature wear during reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 324 d ln excavator (prefix kjr) service repair manual (kjr000...ifoseidkkd
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator, including:
1. Removing and installing the front cover, which involves removing bolts and installing a new gasket.
2. Removing the front housing, which requires supporting the engine, removing bolts, and removing the housing.
3. Installing the front housing, which involves cleaning, applying primer and sealant, positioning the housing, and installing bolts.
Similar to Caterpillar cat 324 d l excavator (prefix dfp) service repair manual (dfp00001 and up) (17)
Caterpillar cat 324 d excavator (prefix tsn) service repair manual (tsn00001 ...fjskekazswdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure instructs to install components in reverse order, noting that all seals and gaskets must be replaced and components cleaned before assembly. Proper tooling and torque specifications are listed for selected assembly steps.
Caterpillar cat 324 d excavator (prefix t2d) service repair manual (t2d00001 ...fjskekazswdmme
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover and internal gears from the final drive housing.
2. Remove the carrier assemblies that contain the planetary gears.
3. Disassemble the carrier assemblies by removing the planetary shafts, thrust washers, and gears.
Caterpillar cat 324 d excavator (prefix mnd) service repair manual (mnd00001 ...fjskekazswdmme
The document provides instructions for disassembling the final drive of a 324D excavator. It involves removing over 30 individual parts in a specific sequence, including the cover, gears, carrier assembly, planetary carrier, shafts and seals. Cleanliness is important to prevent dirt entering during disassembly. Tools including link brackets, eyebolts, and retaining ring pliers are required. The procedure removes components step-by-step and identifies each part and subassembly that must be dismantled from the final drive.
Caterpillar cat 324 d excavator (prefix jzr) service repair manual (jzr00001 ...fjskekazswdmme
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of parts that are spring loaded or require specific orientation. Tools required for the procedures are also listed.
Caterpillar cat 324 d excavator (prefix jat) service repair manual (jat00001 ...fjskekazswdmme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure instructs to install components in the reverse order and notes that all seals and gaskets must be replaced, parts must be cleaned before assembly, and lubricant applied to components. Proper tooling is listed for removing and installing retaining rings, seals, and races.
Caterpillar cat 324 d excavator (prefix dfp) service repair manual (dfp00001 ...fjskekazswdmme
This document provides instructions for disassembling and assembling various components of a Caterpillar 324D and 324D L excavator engine, including:
- Removing and installing the front housing by removing bolts and support pieces.
- Removing and installing the camshaft idler gear by pressing out/in the bearing and aligning timing marks.
- Removing and installing the valve mechanism cover and base by removing/replacing bolts and reconnecting harnesses.
- Removing the rocker shaft and pushrods by loosening adjustment screws, removing bolts, and separating connecting pieces.
The document provides detailed step-by-step instructions with accompanying illustrations for each procedure. Safety notices
Caterpillar cat 324 d excavator (prefix cjx) service repair manual (cjx00001 ...fjskekazswdmme
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing bolts and crankshaft pulley bolts.
Crown pth50 series hand pallet truck service repair manualfjskekazswdmme
This document is a service and parts manual for the PTH50 series pallet truck. It provides instructions for maintenance, troubleshooting, and replacing parts. The manual describes the hydraulic unit functions for raising, lowering and neutral operations. It also provides details on inspecting and lubricating components, checking fluid levels, and removing and disassembling the hydraulic unit.
Crown lp3020 lift truck service repair manualfjskekazswdmme
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown lp3010 lift truck service repair manualfjskekazswdmme
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown gpc3060 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC 3000 series of trucks. It contains information on safety procedures, lifting and jacking the trucks, routine maintenance tasks, hydraulic and electrical systems, and repair instructions. Sections cover general safety, maintenance schedules, hydraulic and transmission component repair, electrical diagrams, operator menus, and specifications for various GPC 3000 truck models.
Crown gpc3055 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC 3000 series of trucks. It contains information on safety procedures, lifting and jacking the trucks, routine maintenance tasks, hydraulic and electrical systems, and repair instructions. The manual includes diagrams of components and lubrication points, specifications for recommended fluids and replacement parts, and torque settings for fasteners. Procedures are provided for servicing the hydraulic unit, drive unit, transmission, and electrical systems.
Crown gpc3045 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC 3000 series of trucks. It contains information on safety procedures, lifting and jacking the trucks, routine maintenance tasks, hydraulic and electrical systems, and repair instructions. The manual includes diagrams of components and lubrication points, specifications for recommended fluids and replacement parts, and torque settings for fasteners. Procedures are provided for servicing the hydraulic unit, drive unit, transmission, and electrical systems.
Crown gpc3040 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC 3000 series of trucks. It contains information on safety procedures, lifting and jacking the trucks, routine maintenance tasks, hydraulic and electrical systems, and repair instructions. Sections cover general safety, maintenance schedules, hydraulic and transmission component repair, electrical diagrams, operator menus, and specifications for various GPC 3000 truck models.
Crown gpc3020 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC 3000 series of trucks. It contains information on safety procedures, lifting and jacking the trucks, routine maintenance tasks, hydraulic and electrical systems, and repair instructions. The manual includes diagrams of components and lubrication points, specifications for recommended fluids and replacement parts, and torque settings for fasteners. Procedures are provided for servicing the hydraulic unit, drive unit, transmission, and electrical systems.
Crown gpc2040 s lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC2000 Series. It provides safety information and procedures for maintenance, repair, and testing of components. The manual contains sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, and electrical diagrams. Safety is the top priority, and all work must be done by qualified personnel according to the instructions in the manual.
Crown gpc2040 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC2000 Series. It provides safety information and procedures for maintenance, repair, and testing of components. The manual contains sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, and electrical diagrams. Safety must be followed when working on the truck including following all applicable regulations and only allowing qualified personnel to perform repairs.
Crown gpc2020 lift truck service repair manualfjskekazswdmme
This document is a maintenance manual for the GPC2000 Series. It provides safety information and procedures for maintenance, repair, and testing of components. The manual contains sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, and electrical diagrams. Safety must be followed when working on the truck including following maintenance schedules and using proper protective equipment. Only authorized personnel should perform repairs.
Crown esr4500 series forklift service repair manualfjskekazswdmme
This document is a maintenance manual for the ESR4500 Series truck. It contains information over multiple pages on safety procedures, component access, maintenance schedules, hydraulic and electrical systems, status codes, and the service level functions. The manual provides maintenance technicians with specifications, repair instructions, component locations, and troubleshooting guides to service the trucks.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302664
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
B. Remove the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit
Injector Hydraulic Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01153092
1. Support the weight of the front of the engine. Remove bolts (1) and front engine support
(2) .
Illustration 2 g01153093
2. Remove bolts (3) and bolts (5). Remove front housing (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:47:19 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302689
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 1 g01153093
1. Clean the joint face on front housing (4) with Tooling (A) .
2. Apply Tooling (B) to the joint face. Allow the primer to dry for at least three to five
minutes.
3. Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (4) must be
installed within ten minutes of applying the sealant.
4. Position front housing (4) on the cylinder block.
5. Install bolts (3) and bolts (5) .
Illustration 2 g01153092
6. Position front engine support (2) and install bolts (1) .
End By:
a. Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector
Hydraulic Pump - Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:48:18 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02230724
Camshaft Idler Gear - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 1 g01125301
1. Remove bolts (4) and retaining plate (1) .
2. Remove camshaft idler gear (2) .
3. Remove bolt (7) and idler shaft (3) from the cylinder block. Remove thrust plate (5) .
4. Use Tooling (A) and a suitable press to remove bearing (6) from camshaft idler gear (2) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 2 g01125304
1. Use Tooling (A) and a suitable press to install bearing (6) in camshaft idler gear (2). Install
the bearing until the bearing is 1.080 ± 0.250 mm (0.0425 ± 0.0098 inch) below the front
face of camshaft idler gear (2) .
2. Position thrust plate (5) and idler shaft (3) on the cylinder block. Install bolt (7). Tighten the
bolt to a torque of 70 ± 15 N·m (51 ± 11 lb ft).
3. Install camshaft idler gear (2) on idler shaft (3). Ensure that timing mark (8) is facing
outward. Align timing mark (8) with timing mark (9) on crankshaft drive gear (10) .
4. Position plate (1) and install bolts (4). Tighten the bolts to a torque of 70 ± 15 N·m (51 ± 11
lb ft).
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:49:18 UTC+0800 2020
3/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302870
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01153188
1/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 1. Remove bolts (1) .
2. Remove valve mechanism cover (2) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01153188
2/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 3 g00945775
1. Position valve mechanism cover (2) on the engine.
2. Install bolts (1). Tighten bolts (1) in a numerical sequence to a torque of 15 ± 3 N·m (11 ± 2
lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:50:17 UTC+0800 2020
3/3
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02302895
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01153198
1. Disconnect harness assembly (4) from valve mechanism cover base (3) .
2. Disconnect harness assemblies (1) .
3. Remove bolts (2), valve mechanism cover base (3), and the gasket from the cylinder head.
Installation Procedure
2/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 2 g01153198
Illustration 3 g01127431
1. Position the gasket and valve mechanism cover base (3) on the cylinder head. Install bolts
(2) and tighten bolts (2) in a numerical sequence to the standard torque.
2. Connect harness assemblies (1) .
3/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 3. Connect harness assembly (4) to valve mechanism cover base (3) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:51:16 UTC+0800 2020
4/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02303847
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place identification marks on each rocker arm and on each pushrod in order to identify the
proper location in the engine for installation.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g01153544
2. Loosen rocker arm adjustment screws (4) .
3. Remove bolts (1), bolts (2), and rocker shaft (3) .
4. Remove inlet valve bridges (5) and pushrods (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:52:16 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307337
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
a. Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01155738
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
Note: Place an identification mark on each of the components of the rocker shaft for
installation purposes.
1. Remove retaining ring (2).
2. Remove stand (3), inlet rocker arms (4), exhaust rocker arms (5), stands (6), and springs (7)
from the rocker shaft.
3. Remove dowel pin (8) and stand (9) from the rocker shaft.
4. Remove plug (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:53:15 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02307338
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate all of the components of the rocker shaft with clean engine oil.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g01155738
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plug (1).
3. Install stand (9) and dowel pin (8) on the rocker shaft.
4. Install springs (7), stands (6), exhaust rocker arms (5), inlet rocker arms (4), and stand (3)
on the rocker shaft.
5. Install retaining ring (2).
End By:
a. Install the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:54:14 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02303869
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 1 g01153544
1. Apply Tooling (A) to both ends of pushrods (6) .
2. Lubricate pushrods (6) with clean engine oil. Install pushrods (6) and inlet valve bridges
(5) .
3. Position rocker shaft (3). Install bolts (1) and bolts (2). Finger tighten bolts (1) and bolts (2).
Tighten bolts (2) and bolts (1) to standard torque.
4. Apply Tooling (A) to each of the button faces of the rocker arms.
5. Adjust the valve lash of the rocker arm by turning rocker arm adjustment screws (4). Refer
to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 23:55:14 UTC+0800 2020
2/2
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D L EXCAVATOR DFP
Configuration: 324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02303932
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
B. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
And Pushrod - Remove".
C. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
D. Remove the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive
Mounting Group - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01153598
1. Disconnect harness assemblies (1), (2), (3), (4), and (5) .
Illustration 2 g01153599
2/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. 2. Disconnect hose assembly (6) and tube assembly (7) .
Illustration 3 g01153600
3. Disconnect tube assembly (8) and tube assembly (10) from turbocharger (9) .
Illustration 4 g01153645
4. Attach a suitable lifting device to cylinder head (11). The weight of cylinder head (11) is
approximately 175 kg (385 lb).
3/4
324D & 324D L Excavators DFP00001-UP (MACHINE) POWERED BY C7 Engine(...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...