This document provides assembly and disassembly instructions for the swing drive of 323E excavator models. It includes 21 steps to disassemble components like the sun gear, carrier assembly, ring gear, housing and shaft. It also includes assembly steps applying anti-seize compound and torque specifications. Tools required include retaining ring pliers, link brackets, sleeves, pullers and hydraulic equipment. Cleanliness is emphasized to prevent contamination of parts.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing components in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of seals is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before assembly and replacing any worn or damaged components.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 352F-VG Excavator (Prefix YEG) Service Repair Manual (YEG0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator model. It begins by listing the required tools and parts. The disassembly instructions describe 32 steps to remove components like plugs, seals, springs, pistons, plates and bearings from the motor. Precautions are provided for parts under spring tension. The assembly section lists specifications for installing 11 components, including torques and seals. Proper lubrication of parts is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing components in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of seals is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before assembly and replacing any worn or damaged components.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 352F-VG Excavator (Prefix YEG) Service Repair Manual (YEG0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator model. It begins by listing the required tools and parts. The disassembly instructions describe 32 steps to remove components like plugs, seals, springs, pistons, plates and bearings from the motor. Precautions are provided for parts under spring tension. The assembly section lists specifications for installing 11 components, including torques and seals. Proper lubrication of parts is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323E LN EXCAVATOR TDW
Configuration: 323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04609390
Swing Drive
SMCS - 5459
Specifications
Illustration 1 g02724358
Table 1
Specification for 148-4679 Swing Drive Gp
Item Qty Part Specification Description
1 1 Torque to 45.0 ± 4.5 N·m (33.2 ± 3.3 lb ft).
1/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 227-6221
Breather As
2 1
114-1399
Gauge Pipe Torque to 60 ± 6 N·m (44 ± 4 lb ft).
3 - -
Apply blue Loctite High Flex GM to the mating surfaces of the ring
gear and the housing.
4 - -
Surfaces of the mounting area, contact area of the bolt and surfaces of
the pinion shaft must be free of paint. Before assembly, the contact
surfaces of the bolt, the washer, and the tightened parts must be clean
and free of protective coating and oil.
Disassembly Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-1863 Retaining Ring Pliers 1
B 138-7575 Link Brackets 2
C
4C-5660 Adapter 2
5F-7369 Puller Leg 2
3H-0465 Push-Puller Plate 2
1P-0820 Hydraulic Puller 1
3H-0468 Puller Plate 2
350-7768 Electric Hydraulic Pump Gp(1)
1
1U-9889 Crossblock 1
D 138-7573 Link Brackets 2
E FT-3023 Sleeve 1
F
5F-7343 Bearing Puller Gp 1
3H-0465 Push-Puller Plate 4
5F-7369 Puller Leg 2
5F-7342 Adapter 2
1P-0820 Hydraulic Puller 1
350-7768 Electric Hydraulic Pump Gp(1)
1
(1)
350-7769 (230 V)
2/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Start By:
a. Remove the swing motor and swing drive.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Illustration 2 g00702449
1. Remove sun gear (1) from carrier assembly (2).
3/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g00702450
2. Remove spacer (3).
Illustration 4 g00702451
3. Remove carrier assembly (2) from ring gear (4).
Illustration 5 g00702452
4. Drive roll pin (5) into shaft (6). Remove shaft (6) and the gear assembly.
4/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00702456
5. Disassemble the gear assembly, as follows: washer (7), gear (8), bearing (9), and washer (10).
Remove roll pin (5) from shaft (6).
6. Repeat Step 4 through Step 5 for the remaining gear assemblies.
Illustration 7 g00702457
7. Remove retaining ring (11). Remove carrier (13) from the sun gear.
Illustration 8 g00702459
8. Use Tooling (A) in order to remove retaining ring (14).
5/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00702583
9. Use two people in order to remove ring gear (15) from housing (16). The weight of ring gear
(15) is approximately 29 kg (65 lb).
Illustration 10 g00702584
10. Remove spacer (17) from carrier assembly (18).
Illustration 11 g00702596
11. Use Tooling (A) to remove retaining ring (19).
6/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01338951
12. Remove carrier assembly (18) from the housing. The weight of carrier assembly (18) is
approximately 25 kg (55 lb).
Illustration 13 g00702640
13. Drive roll pin (20) into shaft (21). Remove shaft (21).
Illustration 14 g00702648
14. Disassemble the gear assembly, as follows: washer (22), bearing (23), gear (24), bearing (25),
and washer (26). Remove roll pin (20) from shaft (21).
15. Repeat Step 13 through Step 14 for the remaining gear assemblies.
7/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01339732
16. Remove bolts (27) from the housing.
Illustration 16 g01339903
Illustration 17 g01339833
17. Attach Tooling (B) and a suitable lifting device in order to remove housing (28). The weight of
housing (28) is approximately 68 kg (150 lb). If shaft assembly (29) is stuck in housing (28)
install Tooling (C) in order to remove shaft assembly (29).
8/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01338949
Illustration 19 g01339781
Illustration 20 g01339877
18. Use Tooling (A) in order to install retaining ring (19). Attach a suitable lifting device to shaft
assembly (29). The weight of shaft assembly (29) is approximately 45 kg (100 lb). Position
shaft assembly (29) onto Tooling (E). Install Tooling (D).
19. Position Tooling (E) and shaft assembly (29) as a unit into a suitable press. The weight of
Tooling (E) and the shaft assembly (29) is approximately 93 kg (205 lb). Use Tooling (A) in
order to remove retaining ring (19). Remove bearings (30) and spacer (31).
Note: If excessive force is required to remove bearings, use Tooling (F) in order to remove the
top bearing first.
9/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g01338948
20. Attach a suitable lifting device to Tooling (D) in order to remove cage (33) and Tooling (E).
Remove cage (33) and Tooling (E) from shaft (32).
Illustration 22 g01340053
21. Remove O-ring seal (34). Remove lip seals (35).
Assembly Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A 5P-1863 Retaining Ring Pliers 1
B 138-7575 Link Brackets 2
D 138-7573 Link Brackets 2
E FT-3023 Sleeve 1
G 1P-0520 Driver Gp 1
H 5P-3931 Anti-Seize Compound 1
J 8M-4856 (1)
Sleeve 1
10/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. K -
Guide Stud
M16 - 2.00 by 140mm
2
L - Loctite Hi Flex GM 1
(1)
This part is being discontinued. Replace with 367-6742 Sleeve .
Note: Cleanliness is an important factor. Before assembly, clean all parts in cleaning fluid. Allow the
parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the
parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts
for replacement.
Illustration 23 g01339794
Illustration 24 g01339807
1. Use a suitable press and Tooling (G) in order to install lip seal (35) into cage (33).
2. Use two people to place shaft (32) in a suitable press. The weight of shaft (32) is approximately
30 kg (65 lb). Install cage (33). Install O-ring seal (34).
11/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 25 g01339812
Illustration 26 g01339149
3. Apply Tooling (H) to inner diameter of the bearing and the shaft. Use a suitable press and
Tooling (J) in order to install bearing (30). Install spacer (31). The bevel of the spacer must
face upward.
4. Install bearing (30).
Illustration 27 g01339824
12/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g01339903
5. Attach a suitable lifting device to shaft assembly (29). Use Tooling (A) in order to install
retaining ring (19). Install shaft assembly (29) onto Tooling (E). Remove the suitable lifting
device.
6. Attach Tooling (B) and a suitable lifting device to housing (28). Install housing (28) on the
shaft assembly. Position the shaft assembly to the side by 90 degrees. Remove tooling (E).
Illustration 29 g01339732
7. Install bolts (27).
Illustration 30 g00703698
13/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 8. Assemble the gear assembly, as follows: washer (22), bearing (23), gear (24), bearing (25), and
washer (26).
Illustration 31 g00702640
Illustration 32 g00703700
9. Use a deburring tool in order to remove the metal burr from the openings in the carrier. Install
shaft (21) and the gear assembly into the carrier assembly. Drive roll pin (20) into shaft (21).
Orient the split in roll pin (20) vertically to the carrier. Align the split in the roll pin to the top
or to the bottom. Make a stake mark on each side of the roll pin hole in the carrier. Each stake
mark should be approximately 2.25 ± 0.75 mm (0.090 ± 0.030 inch) from the outside diameter
of the roll pin hole.
10. Repeat Step 8 through Step 9 for the remaining gear assemblies.
14/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 33 g01338951
11. Install carrier assembly (18) into the housing. The weight of carrier assembly (18) is
approximately 25 kg (55 lb).
Illustration 34 g00702596
12. Use Tooling (A) to install retaining ring (19).
Illustration 35 g00702584
13. Install spacer (17) into carrier assembly (18).
15/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 36 g01340279
Illustration 37 g00702583
14. Apply Tooling (L) to the face of housing (16). Install Tooling (K) in order to help align the
housing and the ring gear. Use two people in order to install ring gear (15) onto housing (16).
The weight of ring gear (15) is approximately 29 kg (65 lb).
Illustration 38 g00702459
15. Install retaining ring (14) into the sun gear.
16/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 39 g00702457
16. Install carrier (13) into the sun gear. Install retaining ring (11) into sun gear (12).
Illustration 40 g00703707
17. Assemble the gear assembly, as follows: washer (7), gear (8), bearing (9), and washer (10)
Illustration 41 g00702452
17/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 42 g00703700
18. Use a deburring tool in order to remove the metal burr from the openings in the carrier. Install
shaft (6) and the gear assembly into the carrier assembly. Drive roll pin (5) into shaft (6).
Orient the split in roll pin (5) vertically to the carrier. Align the split in the roll pin to the top or
to the bottom. Make a stake mark on each side of the roll pin hole in the carrier. Each stake
mark should be approximately 2.25 ± 0.75 mm (0.090 ± 0.030 inch) from the outside diameter
of the roll pin hole.
19. Repeat Step 17 through Step 18 for the remaining gear assemblies.
Illustration 43 g00702451
20. Install carrier assembly (2) into ring gear (4).
18/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 44 g00702450
21. Install spacer (3).
Illustration 45 g00702449
22. Install sun gear (1) into carrier assembly (2).
End By:
a. Install the swing motor and swing drive.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 14:12:36 UTC+0800 2020
19/19
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERE...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323E LN EXCAVATOR TDW
Configuration: 323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04491082
Swing Gear and Bearing
SMCS - 7063
Specifications
1/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g02724727
Typical example
Table 1
Specification for 333-2969 Gear and Bearing Gp and 333-2966 Gear and Bearing Gp
Item Qty Part Specification Description
- - -
Position "S" that is on inner race (12) relative to the carbody
assembly (1) and bearing stopper (2). Refer to Illustration 1.
- - - The five holes which are marked “3” are not for use.
4 4 8T-4136
Bolt
Apply blue Loctite 242 to the threads.
Torque to 20 ± 2 N·m (177 ± 18 lb in).
2/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 5 8
8T-4136
Bolt
Apply blue Loctite 242 to the threads.
Torque to 37 ± 4 N·m (27 ± 3 lb ft).
6 1
7Y-1650
Hose
Clamp
Torque to 5.39 ± 0.49 N·m (47.71 ± 4.34 lb in).
7 2
8T-4137
Bolt
Apply blue Loctite 242 to the threads.
Torque to 37 ± 4 N·m (27 ± 3 lb ft).
8 1
096-4902
Dowel
Apply Loctite C5A Cooper Anti-Seize to the dowel holes.
9 - -
Apply blue Loctite High Flex GM between the mating surfaces of
the gear group and upper frame assembly. Apply blue Loctite High
Flex GM between the mating surfaces of the gear group and
carbody assembly.
10 37
8T-0362
Bolt
Apply Loctite C5A Cooper Anti-Seize to the threads. Omit the bolt
seats and surfaces of the washers.
Torque for the bolts except for the Akashi facility to 568 ± 59 N·m
(419 ± 44 lb ft).
Torque for the bolts for the Akashi facility to 294 ± 29 N·m
(217 ± 21 lb ft).
Additional torque for the bolts for the Akashi facility to 50 ± 5
degrees.
11 40
8T-0360
Bolt
Apply Loctite C5A Cooper Anti-Seize to the threads. Omit the bolt
seats and surfaces of the washers.
Torque for the bolts except for the Akashi facility to 568 ± 59 N·m
(419 ± 44 lb ft).
Torque for the bolts for the Akashi facility to 294 ± 29 N·m
(217 ± 21 lb ft).
Additional torque for the bolts for the Akashi facility to 50 ± 5
degrees.
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7576 Link Bracket 4
B -
Guide Bolts
M20 x 2.5 by 150mm
2
Start By:
a. Separate the upper frame from the undercarriage frame.
3/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 1. Remove all the grease from the swing gear and bearing. Put the grease in a suitable
container for storage or disposal.
Illustration 2 g02672179
2. Remove bolts (1). Install bolts and mark swing gear and bearing (2) or alignment purposes
Illustration 3 g02672908
3. Attach Tooling (A) and a suitable lifting device in order to remove swing gear and bearing
(2) from the undercarriage (3).
Installation Procedure
1. Install swing gear and bearings (2) in reverse order of removal.
End By:
a. Connect the upper frame from the undercarriage frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 14:13:35 UTC+0800 2020
4/4
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323E LN EXCAVATOR TDW
Configuration: 323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04507920
Pilot Valve
SMCS - 5059
Removal Procedure
Start By:
a. Release the hydraulic system pressure.
Illustration 1 g02686500
1. Disconnect all hose assemblies (1). Disconnect all harness assemblies (2).
1/2
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g02686503
2. Remove four bolts (3) and pilot valve (4).
Installation Procedure
1. Install pilot valve (4) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 14:14:35 UTC+0800 2020
2/2
323E L, 323E LN & 323E SA Excavators TDW00001-UP (MACHINE) POWERED ...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...