This document provides installation instructions for removing and installing a crankshaft front seal on a 323 excavator. It outlines 20 steps to remove the existing seal using a specialty tool. These include preventing the crankshaft from rotating, installing guide studs, and using bolts to pull the seal from the front cover. New seal installation requires cleaning parts and pressing the new seal into place, ensuring proper orientation. Special tools and torque specifications are provided to correctly complete the procedure.
This document provides installation instructions for a rear power takeoff (RPTO) on a 323 excavator with a C7.1 engine. It involves cleaning components, pressing bearings into housings, aligning gears and idler hubs, lubricating and installing components, and tightening bolts to specified torques. The instructions also cover removing and installing the crankshaft pulley assembly and front seal.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...fjsqazkekdmme
The document provides instructions for installing the rear power take-off (RPTO) on a 950K wheel loader. It describes cleaning components, aligning sleeve bearings, installing gears and idler hubs onto the flywheel housing using press tools, lubricating parts, and tightening bolts to specified torques. The 20-step procedure includes installing adapters and seals, checking backlash and end play, and attaching the gear assembly to the crankshaft.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...ujdkkdkdmm
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. The removal procedure involves using a special tool to press the seal out of the front cover. For installation, the new seal is pressed into the front cover using the same tool. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...wedsrffcdgdv
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. It describes using a special tool to press the seal out of and into the front cover. Cleanliness is emphasized to prevent premature wear. The instructions are part of a service manual for Caterpillar C7.1 engines.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides installation instructions for a rear power takeoff (RPTO) on a 323 excavator with a C7.1 engine. It involves cleaning components, pressing bearings into housings, aligning gears and idler hubs, lubricating and installing components, and tightening bolts to specified torques. The instructions also cover removing and installing the crankshaft pulley assembly and front seal.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...fjsqazkekdmme
The document provides instructions for installing the rear power take-off (RPTO) on a 950K wheel loader. It describes cleaning components, aligning sleeve bearings, installing gears and idler hubs onto the flywheel housing using press tools, lubricating parts, and tightening bolts to specified torques. The 20-step procedure includes installing adapters and seals, checking backlash and end play, and attaching the gear assembly to the crankshaft.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...ujdkkdkdmm
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. The removal procedure involves using a special tool to press the seal out of the front cover. For installation, the new seal is pressed into the front cover using the same tool. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...wedsrffcdgdv
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. It describes using a special tool to press the seal out of and into the front cover. Cleanliness is emphasized to prevent premature wear. The instructions are part of a service manual for Caterpillar C7.1 engines.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...fusjekkdmdmd2w
The documents provide instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
1. Installing the flywheel, which involves heating the ring gear, cleaning parts, using guide bolts and lifting devices, and tightening bolts to the specified torque.
2. Removing the crankshaft rear seal, which is non-serviceable, requiring replacement of the entire housing assembly after removing setscrews.
3. Installing the crankshaft rear seal housing assembly using an alignment tool and tightening setscrews to the specified torque.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...fusjekkdmdmd2w
- The document provides instructions for installing a cylinder head on a 3054C engine.
- It describes cleaning the cylinder block and head, installing a new gasket and dowels, and lifting the head into place using guide bolts.
- The setscrews securing the cylinder head are then installed and tightened in numerical order to the specified torque.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling components such as the final drive, travel motor, counterbalance valve housing, barrel assembly, and piston assemblies. Safety notices are included to warn of potential injuries from parts propelled by springs, hydraulic pressure, and hot oil.
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer tools, for reclaiming
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a 3054C engine. The flywheel removal procedure involves installing guide bolts and link bracket to support the flywheel weight before removing all setscrews. For installation, the ring gear may need to be heated to 250°C and aligned correctly. The crankshaft rear seal housing is non-serviceable and must be replaced if removed. A plastic sleeve protects the new seal during installation. The crankshaft wear sleeve is removed using a puller and installed using an oil seal installer, bolt, and washer.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...fusjekkdmdmd2w
The documents provide instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
1. Installing the flywheel, which involves heating the ring gear, cleaning parts, using guide bolts and lifting devices, and tightening bolts to the specified torque.
2. Removing the crankshaft rear seal, which is non-serviceable, requiring replacement of the entire housing assembly after removing setscrews.
3. Installing the crankshaft rear seal housing assembly using an alignment tool and tightening setscrews to the specified torque.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...fusjekkdmdmd2w
- The document provides instructions for installing a cylinder head on a 3054C engine.
- It describes cleaning the cylinder block and head, installing a new gasket and dowels, and lifting the head into place using guide bolts.
- The setscrews securing the cylinder head are then installed and tightened in numerical order to the specified torque.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling components such as the final drive, travel motor, counterbalance valve housing, barrel assembly, and piston assemblies. Safety notices are included to warn of potential injuries from parts propelled by springs, hydraulic pressure, and hot oil.
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer tools, for reclaiming
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a 3054C engine. The flywheel removal procedure involves installing guide bolts and link bracket to support the flywheel weight before removing all setscrews. For installation, the ring gear may need to be heated to 250°C and aligned correctly. The crankshaft rear seal housing is non-serviceable and must be replaced if removed. A plastic sleeve protects the new seal during installation. The crankshaft wear sleeve is removed using a puller and installed using an oil seal installer, bolt, and washer.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292388
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components of the rear power take-off (RPTO) are clean and free from wear
and damage.
1/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g02069024
2. If necessary, follow Steps 2.a through Steps 2.c in order to install the sleeve bearing from
the flywheel housing.
a. Accurately align oil Holes (X) in sleeve bearing (20) with the oil holes in flywheel
housing (9).
b. Use Tooling (A) in order to install sleeve bearing (20) into flywheel housing (9).
Note: Ensure that the oil holes are correctly aligned. If the oil holes are not correctly
aligned, the sleeve bearing should be removed.
c. Repeat Step 2.a through Steps 2.c in order to install sleeve bearing (21) to flywheel
housing (9).
3/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g02069021
3. If necessary, follow Steps 3.a through Steps 3.d in order to install the sleeve bearing to the
gears.
a. Place gear (17) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (20) with Grooves (Y) in gear (17).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19) into gear
(17).
d. Repeat Steps 3.a through Step 3.c in order to install the sleeve bearing to gear (18).
4. Lubricate idler hub (15) and gear (17) with clean oil. Install idler hub (15) to gear (17).
Note: Ensure that the gear and the idler hub are correctly oriented.
5. Install gear (17) and idler hub (15) assembly to flywheel housing (9).
Note: Ensure that the oil hole in the idler hub is correctly positioned.
6. Install bolts (13) to idler hub (15) and hand tighten bolts.
Note: Ensure that the idler hub is correctly aligned to the flywheel housing.
7. Repeat Steps 4 through Step 6 in order to install gear (18), idler hub (16) and bolts (14) to
flywheel housing (9).
5/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 8. Tighten bolts (13) and bolts (14) to a torque of 100 N·m (74 lb ft).
9. Ensure that there is tactile backlash between gear (17) and gear (18). Ensure that there is
end play between the idler hubs and the gears.
Illustration 5 g02069020
10. install gear assembly (11) and gear assembly (12) to flywheel housing (9).
6/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 7 g02070473
11. If necessary, follow Steps 11.a through Steps 11.c in order to install the sleeve bearing to
the adapter.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to install sleeve bearing (10) into
adapter (2).
c. Repeat Steps 11.a through Step 11.b in order to install the sleeve bearing into adapter
(5).
12. Install a new O-ring seal (3) (not shown) to adapter (2).
13. Install adapter (2) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
14. Install bolts (1) and tighten the bolts to a torque of 55 N·m (41 lb ft).
15. Install a new O-ring seal (6) (not shown) to adapter (5).
16. Install adapter (5) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
17. Install bolts (4) and tighten the bolts to a torque of 55 N·m (41 lb ft).
8/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 18. Ensure that there is tactile backlash between the gears. Ensure that there is end play between
the gears and the flywheel housing and the adapters.
19. Install gear (7) to crankshaft (8).
20. If necessary, install the OEM equipment to the rear power take-off (RPTO).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:14:00 UTC+0800 2020
9/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05909481
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Remove Tooling (A) .
2/3
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:15:00 UTC+0800 2020
3/3
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05909490
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.e in order to install vibration damper,
crankshaft pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Fri Sep 25 01:16:00 UTC+0800 2020
3/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292118
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly
2/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03413520
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:16:59 UTC+0800 2020
4/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292119
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g03429500
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (1).
Note: Do not damage the edge of the housing for the crankshaft front seal.
2. Screw bolt (2) into Tooling (A) in order to remove crankshaft front seal (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly
2/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front seal in the front housing is clean and free from
damage.
Illustration 2 g03429501
2. Assemble Tooling (B).
3. Align new crankshaft front seal (1) to the front housing.
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (1). Ensure that the front face of the seal is
installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch) into the front housing.
5. Remove Tooling (B) from the crankshaft.
End By:
3/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:17:59 UTC+0800 2020
4/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292301
Front Cover - Remove and Install - Heavy Duty Front Cover
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump- Remove" for
the correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
c. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
d. Remove the crankshaft front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
1/5
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g03410400
1. Remove bolts (3), bolts (4), and bolts (5). Identify the positions of bolts of different length.
2. Remove front cover (1) from the front housing.
3. Remove gasket (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Studs
M8 by 70 mm
2
B 364-7210 Front Cover Alignment Tool 1
2/5
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...