The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...fusjejkdkmse
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head over to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4. Installing the valve seat inserts, valves, and electronic unit injectors to complete the job.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...fjkskedmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and multi-step procedures for removal and installation, which include removing other engine components, using specialty tools to remove the guides and seats, cleaning parts, and ensuring proper installation height or alignment. Safety notices are provided to keep parts clean and contain fluids properly during the process.
Caterpillar cat 325 b l excavator (prefix 4ds) service repair manual (4ds0000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and high temperature sealer if the manifold has multiple pieces, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a 325-A excavator powered by a 3116 engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets and torque specifications. Tools required are also listed.
Caterpillar cat 325 d l mobile hyd power unit (prefix h3n) service repair man...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using special tools to compress the valve springs, and removing components in the proper order - retainer locks, springs, washers and seals before removing the valves. Installation is the reverse process, lubricating and seating the valves before reinstalling the spring and retainer components. Safety precautions are outlined to avoid injury from the force of compressed springs.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 322 c excavator (prefix fed) service repair manual (fed00001 ...ujdfjkkskmem
This document provides instructions for disassembling a pilot valve used in 322C and 322C L excavators powered by a 3126 engine. The summary is:
1. The pilot valve must first be removed from the machine by disconnecting hoses, wires, switches, and removing mounting bolts.
2. To disassemble the pilot valve, over 30 individual parts must be removed including fittings, seals, covers, springs, bushings, and spools.
3. Cleanliness is important during disassembly to prevent contamination, and identification marks should be made on parts.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjkskedmme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...fusjejkdkmse
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head over to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4. Installing the valve seat inserts, valves, and electronic unit injectors to complete the job.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...fjkskedmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and multi-step procedures for removal and installation, which include removing other engine components, using specialty tools to remove the guides and seats, cleaning parts, and ensuring proper installation height or alignment. Safety notices are provided to keep parts clean and contain fluids properly during the process.
Caterpillar cat 325 b l excavator (prefix 4ds) service repair manual (4ds0000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and high temperature sealer if the manifold has multiple pieces, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a 325-A excavator powered by a 3116 engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets and torque specifications. Tools required are also listed.
Caterpillar cat 325 d l mobile hyd power unit (prefix h3n) service repair man...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using special tools to compress the valve springs, and removing components in the proper order - retainer locks, springs, washers and seals before removing the valves. Installation is the reverse process, lubricating and seating the valves before reinstalling the spring and retainer components. Safety precautions are outlined to avoid injury from the force of compressed springs.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 322 c excavator (prefix fed) service repair manual (fed00001 ...ujdfjkkskmem
This document provides instructions for disassembling a pilot valve used in 322C and 322C L excavators powered by a 3126 engine. The summary is:
1. The pilot valve must first be removed from the machine by disconnecting hoses, wires, switches, and removing mounting bolts.
2. To disassemble the pilot valve, over 30 individual parts must be removed including fittings, seals, covers, springs, bushings, and spools.
3. Cleanliness is important during disassembly to prevent contamination, and identification marks should be made on parts.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjkskedmme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjsekmsmmes
The document provides instructions for removing and installing valve guides and valve seat inserts in a Caterpillar C6.4 engine. It describes:
1) Removing the valves, electronic unit injectors, and turning the cylinder head upside down to access the valve guides.
2) Using specialty tools to remove the old valve guides and install new guides.
3) Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4) Reinstalling the valves and electronic unit injectors after installing new guides and inserts.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...jfjskekdhnejd
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...cdfzxs
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
Kubota v3800 di t-e3cb diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document consists of detailed checklists for performing maintenance at regular intervals, with items to check daily, every 50 hours, 250 hours, 500 hours, 1000 hours, and longer intervals. It concludes by listing special tools needed for servicing the engines.
Kubota v3800 di t-e3bg diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then lists general precautions and a maintenance checklist. The bulk of the document provides detailed checklists for various maintenance intervals, from daily checks to every 3000 hours. It concludes with an overview of special tools needed for servicing.
Kubota v3800 di t-e3b diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document lists check points that should be performed at regular intervals, such as daily, every 50 hours, every 250 hours, and annually. It concludes by listing special tools that may be required for maintenance and servicing.
More Related Content
Similar to Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac00001 and up)
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjsekmsmmes
The document provides instructions for removing and installing valve guides and valve seat inserts in a Caterpillar C6.4 engine. It describes:
1) Removing the valves, electronic unit injectors, and turning the cylinder head upside down to access the valve guides.
2) Using specialty tools to remove the old valve guides and install new guides.
3) Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4) Reinstalling the valves and electronic unit injectors after installing new guides and inserts.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...jfjskekdhnejd
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...cdfzxs
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
Similar to Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac00001 and up) (18)
Kubota v3800 di t-e3cb diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document consists of detailed checklists for performing maintenance at regular intervals, with items to check daily, every 50 hours, 250 hours, 500 hours, 1000 hours, and longer intervals. It concludes by listing special tools needed for servicing the engines.
Kubota v3800 di t-e3bg diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then lists general precautions and a maintenance checklist. The bulk of the document provides detailed checklists for various maintenance intervals, from daily checks to every 3000 hours. It concludes with an overview of special tools needed for servicing.
Kubota v3800 di t-e3b diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document lists check points that should be performed at regular intervals, such as daily, every 50 hours, every 250 hours, and annually. It concludes by listing special tools that may be required for maintenance and servicing.
Kubota v3600 t-e3 cb diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document lists check points that should be performed at regular intervals, such as daily, every 50 hours, every 250 hours, and annually. It concludes by listing special tools that may be required for maintenance and servicing.
Kubota v3600 t-e3 bg diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then lists general precautions and a maintenance checklist. The bulk of the document provides detailed checklists for various maintenance intervals, from daily checks to every 3000 hours. It concludes with an overview of special tools needed for servicing.
Kubota v3600 t-e3 b diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document consists of detailed checklists for performing maintenance at regular intervals, with items to check daily, every 50 hours, 250 hours, 500 hours, 1000 hours, and longer intervals. It concludes by listing special tools needed for servicing tasks.
Kubota v3600 e3 cb diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document lists check points that should be performed at regular intervals, such as daily, every 50 hours, every 250 hours, and annually. It concludes by listing special tools that may be required for maintenance and servicing.
Kubota v3300 t-e2 b diesel engine service repair manualfjkskekxsdcmdmme
The document provides information on servicing a diesel engine. It begins with identifying the engine model and serial number. The second part describes the engine identification codes and emission control details. The third part lists general precautions for servicing including arranging removed parts carefully, using special tools as required, and disconnecting the battery before working on live wires.
Kubota v3300 e3 bg diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document lists check points that should be performed at regular intervals, such as daily, every 50 hours, every 250 hours, and annually. It concludes by listing special tools that may be required for maintenance and servicing.
Kubota v3300 e2 b diesel engine service repair manualfjkskekxsdcmdmme
The document provides information on servicing a diesel engine. It begins with identifying the engine model and serial number. The second part describes the engine identification codes and emission control details. The third part lists general precautions for servicing including arranging removed parts carefully, using special tools as required, and disconnecting the battery before working on live wires.
This document provides a summary of tractor transmission mechanisms, including:
1. Sliding mesh, constant mesh, and synchronous mesh transmission gears that transfer power from the clutch to the wheels.
2. Hydraulic shuttle shift and swing shift mechanisms that allow changing direction without using the clutch.
3. Dual speed and hydrostatic transmission types that provide variable speed control through hydraulic components.
4. Glide shift transmissions that combine gear changes with continuously variable speed control for smooth shifting.
5. Power shift systems using electric and hydraulic components for automated gear changes based on vehicle speed or load.
Detailed diagrams and explanations are given for the construction and operation of various clutch, transmission, and
Hyundai 70 ds 7e forklift truck service repair manualfjkskekxsdcmdmme
This document provides an overview and outline of the contents of a service manual for a machine. It is divided into 8 sections that cover general information, removal and installation procedures, descriptions of the power train, brake, steering, hydraulic, electrical, and mast systems. The sections are further broken down into groups that describe the structure, operation, maintenance, troubleshooting, disassembly/assembly, and adjustment procedures for the various components within each system. Safety symbols are defined that will be used throughout the manual. Conversion tables are also provided to allow simple conversions between different units of measurement.
Kubota v3600 e3 b diesel engine service repair manualfjkskekxsdcmdmme
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document lists check points that should be performed at regular intervals, such as daily, every 50 hours, every 250 hours, and annually. It concludes by listing special tools that may be required for maintenance and servicing.
Hyundai 70 df 7 forklift truck service repair manualfjkskekxsdcmdmme
This document provides an overview and outline of the contents of a service manual for a machine. It includes 8 sections that cover general information, removal and installation procedures, descriptions of the power train, brake, steering, hydraulic, electrical, and mast systems. Each section includes groups that describe the structures, operations, inspections, troubleshooting, disassembly/assembly procedures, and adjustments for the various components and systems. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 70 d 7e forklift truck service repair manualfjkskekxsdcmdmme
This document provides instructions for disassembling and assembling a steering unit. It includes diagrams labeling the parts and components. The instructions describe how to remove parts like the end cover, gearwheel set, cardan shaft, distributor plate, check valve, bearing races and thrust bearing. Reassembly instructions provide details on installing parts like the spool, sleeve, cross pin, neutral position springs, O-rings and lip seal in the correct order and orientation. Torque specifications are also provided for mounting bolts.
Hyundai 60 ds 7e forklift truck service repair manualfjkskekxsdcmdmme
This document provides an overview and outline of the contents of a service manual for a machine. It is divided into 8 sections that cover general information, removal and installation procedures, descriptions of the power train, brake, steering, hydraulic, electrical, and mast systems. The sections are further broken down into groups that describe the structure, operation, maintenance, troubleshooting, disassembly/assembly, and adjustment procedures for the various components within each system. Safety symbols are defined that will be used throughout the manual. Conversion tables are also provided as a reference.
Hyundai 60 df 7 forklift truck service repair manualfjkskekxsdcmdmme
This document provides an overview and outline of the contents of a service manual for a machine. It includes 8 sections that cover general information, removal and installation procedures, descriptions of the power train, brake, steering, hydraulic, electrical, and mast systems. Each section includes groups that describe the structures, operations, inspections, troubleshooting, disassembly/assembly procedures, and adjustments for the various components and systems. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:29:06 UTC+0800 2020
4/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:31:04 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:32:03 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:33:03 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:34:02 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:35:01 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377713
1. Install a new gasket (2) (not shown). Install engine oil bypass valve (1). Tighten engine oil
bypass valve (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:36:00 UTC+0800 2020
2/2
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751822
Engine Oil Pump Relief Valve - Remove and Install
SMCS - 1304-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377698
1/3
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g01377701
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove engine oil pump relief valve (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 3 g01377701
Illustration 4 g01377698
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install engine oil pump relief valve (1). Tighten engine oil pump relief valve (1) to a torque
of 59 ± 10 N·m (44 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 22:37:00 UTC+0800 2020
3/3
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D LN EXCAVATOR RAC
Configuration: 323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02741773
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolts (1) from the cover (2).
2. Remove cover (2) for the engine oil pump from the front housing. Remove gasket (3) (not
shown).
Illustration 2 g00607770
3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
2/4
323D LN & 323D S Excavators RAC00001-UP (MACHINE) POWERED BY C6.4 E...
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...