The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsfskekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...uudfjjjskkemmd
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...uujjfjjkskmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...ujjfdjkjskkmdm
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsjefkksekmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsefjfkksekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsfskekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...uudfjjjskkemmd
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...uujjfjjkskmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...ujjfdjkjskkmdm
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsjefkksekmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsefjfkksekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...yushantuanjing
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires removing other components like the alternator first.
3. Cleaning and applying sealant when installing the front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires draining fluids first.
3. Cleaning and applying sealant when reinstalling the front housing.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...sijipang18046
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...r8qvui4a
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
Caterpillar Cat 322C FM EXCAVATOR (Prefix M2H) Service Repair Manual (M2H0000...jfksemmdm3e
This document provides instructions for removing and installing the camshaft idler gear on a Caterpillar 3126B engine. The removal procedure involves rotating the crankshaft to align timing marks, removing mounting bolts and plates, and pressing the bearing out of the idler gear. The installation procedure specifies cleaning parts, pressing the bearing into the idler gear, positioning the idler shaft and securing with a bolt, and aligning timing marks. Tools include a driver and press. Proper containment of fluids is emphasized.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
More Related Content
Similar to Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual (EMR00001 and up).pdf
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...yushantuanjing
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires removing other components like the alternator first.
3. Cleaning and applying sealant when installing the front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires draining fluids first.
3. Cleaning and applying sealant when reinstalling the front housing.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...sijipang18046
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...r8qvui4a
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
Caterpillar Cat 322C FM EXCAVATOR (Prefix M2H) Service Repair Manual (M2H0000...jfksemmdm3e
This document provides instructions for removing and installing the camshaft idler gear on a Caterpillar 3126B engine. The removal procedure involves rotating the crankshaft to align timing marks, removing mounting bolts and plates, and pressing the bearing out of the idler gear. The installation procedure specifies cleaning parts, pressing the bearing into the idler gear, positioning the idler shaft and securing with a bolt, and aligning timing marks. Tools include a driver and press. Proper containment of fluids is emphasized.
Similar to Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual (EMR00001 and up).pdf (8)
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...fusjekkdmdmd2w
The documents provide instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
1. Installing the flywheel, which involves heating the ring gear, cleaning parts, using guide bolts and lifting devices, and tightening bolts to the specified torque.
2. Removing the crankshaft rear seal, which is non-serviceable, requiring replacement of the entire housing assembly after removing setscrews.
3. Installing the crankshaft rear seal housing assembly using an alignment tool and tightening setscrews to the specified torque.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02370081
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Illustration 1 g00612677
1. Remove bolts (2), crankshaft vibration damper (1), and the spacers from the crankshaft
pulley.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00612684
2. Remove belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
3. Remove bolts (4).
4. Remove crankshaft pulley (5).
Installation Procedure
Illustration 3 g00612684
1. Position crankshaft pulley (5) on the crankshaft. Install bolts (4) and tighten the bolts to a
torque of 160 ± 30 N·m (118 ± 22 lb ft).
2. Install belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
Note: Check the alignment marks on the rubber vibration dampers for proper alignment.
The rubber vibration damper should be replaced if the rubber vibration damper is out of
alignment. Refer to Specifications, "Vibration Damper".
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00612677
3. Install the spacers and crankshaft vibration damper (1). Install bolts (2) and tighten to a
torque of 55 ± 10 N·m (40 ± 7 lb ft).
4. Adjust the tension of the belt. Refer to Specifications, "Belt Tension Chart".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:10:23 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982085
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00989224
1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:11:19 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982092
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00989228
1. Use Tooling (C) to install crankshaft front seal (1).
Note: The crankshaft seal is designed to be installed dry.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:12:15 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379367
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00728351
1. Remove four bolts (1) that fasten bracket (2) on the front of the engine.
Illustration 2 g00728369
2. Remove the bolts (3) and front cover (4) from the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:13:10 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379400
Front Cover - Install
SMCS - 1166-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The rear face of the cover and the front face of the housing must be clean.
1. Inspect the condition of the housing cover gasket. Replace the gasket, if necessary.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00728369
2. Install the housing cover gasket.
3. Position front cover (4) on the front housing. Install the bolts (3) on front cover (4).
Illustration 2 g00728351
4. Position bracket (2) on the front of the engine.
5. Install four bolts (1) that fasten bracket (2) on the engine.
End By:
a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:14:06 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983906
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01028155
2. Remove belt tightener (2).
3. Remove front housing (3).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:15:02 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983976
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01028155
1. Clean the joint face on front housing (3) with Tooling (A).
2. Apply Tooling (B) to the joint face. Allow the primer to dry for at least three to five
minutes.
Note: Do not allow Tooling (C) to seal the main oil passage on front housing (3).
3. Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (3) must be
installed within ten minutes of applying the sealant.
4. Install front housing (3) on the cylinder block.
5. Install belt tightener (2).
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01028154
6. Install front engine support (1).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
b. Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:15:58 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02375078
Camshaft Idler Gear - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01027207
1. Rotate the crankshaft until the number one piston is at the top center position. Timing mark
(4) for camshaft idler gear (2) should be in line with timing mark (5) for crankshaft drive
gear (6).
2. Remove the bolts that fasten plate (1) to idler shaft (3). Remove plate (1).
3. Slide camshaft idler gear (2) from idler shaft (3).
4. Use Tooling (A) and a suitable press to remove the bearing from camshaft idler gear (2).
5. Remove the bolt and idler shaft (3) from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
NOTICE
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01027207
1. Position idler shaft (3) on the cylinder block. Install the bolt that holds idler shaft (3) to the
cylinder block. Tighten the bolt to a torque of 70 ± 15 N·m (51 ± 11 lb ft).
2. Use Tooling (A) and a suitable press to install the bearing in camshaft idler gear (2). Install
the bearing until the bearing is 0.40 ± 0.25 mm (0.016 ± 0.010 inch) below the front face of
camshaft idler gear (2).
3. Install camshaft idler gear (2) on idler shaft (3). Align timing mark (4) for camshaft idler
gear (2) with timing mark (5) for crankshaft drive gear (6).
4. Position plate (1) and install the bolts. Tighten the bolts to a torque of 70 ± 15 N·m
(51 ± 11 lb ft).
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:16:53 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02370572
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01182877
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 1. Remove bolts (2) and valve mechanism cover (1).
2. Remove the seal from valve mechanism cover (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01182877
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g01182875
1. Install the seal in valve mechanism cover (1).
2. Position valve mechanism cover (1) on the engine and install bolts (2). Tighten the bolts in a
numerical sequence.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:17:49 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982239
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Disconnect the harness assembly from the valve mechanism cover base.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g01027286
2. Disconnect harness assemblies (1) from each of the unit injectors.
3. Remove valve mechanism cover base (2).
Installation Procedure
Illustration 2 g01027286
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...