This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes, and removing mounting bolts and clips. The installation procedure specifies cleaning and lubricating parts, reconnecting linkages and tubes using the special tools, and adjusting settings once installed. Proper cleanup and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. It describes:
1) Removing the fuel shutoff solenoid, disconnecting control cables, and removing clips, tubes, and bolts to detach the governor.
2) Installing new O-rings, attaching the governor with bolts and clips, reconnecting control cables, and reinstalling fuel shutoff components.
3) Removing the rocker shaft, pushrods, clips and bolts to detach the fuel injection control linkage from the governor.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...fjskefksemer
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Components like O-rings and seals are also removed. Installation is the reverse, applying lubricant to new seals and using tools to reconnect linkages and tubes. Proper torque specifications are listed for bolts. Reference documents are also provided for additional governor information.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...fujsekfkksemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Components like O-rings and seals are also removed. Installation is the reverse, applying lubricant to new seals and using tools to reconnect everything. Precise instructions with illustrations are provided to ensure correct installation.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with a list of required tools. The removal procedure involves 11 steps that remove connecting tubes, clips, bolts and seals to detach the governor. The installation procedure reverses these steps, replacing seals and using special tools to reattach connecting pins and tubes. Proper lubrication of seals and adjustment of fuel settings are emphasized.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation.
It also references other documents for additional governor information and maintenance guidelines.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...fujsefkksemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation.
It also references other documents for additional governor information and maintenance guidelines.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...ujfdjjkjskkemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. It describes:
1) Removing the fuel shutoff solenoid, disconnecting control cables, and removing clips, tubes, and bolts to detach the governor.
2) Installing new O-rings, attaching the governor with bolts and clips, reconnecting control cables, and reinstalling fuel shutoff components.
3) Removing the rocker shaft, pushrods, clips and bolts to detach the fuel injection control linkage from the governor.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...fjskefksemer
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Components like O-rings and seals are also removed. Installation is the reverse, applying lubricant to new seals and using tools to reconnect linkages and tubes. Proper torque specifications are listed for bolts. Reference documents are also provided for additional governor information.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...fujsekfkksemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Components like O-rings and seals are also removed. Installation is the reverse, applying lubricant to new seals and using tools to reconnect everything. Precise instructions with illustrations are provided to ensure correct installation.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with a list of required tools. The removal procedure involves 11 steps that remove connecting tubes, clips, bolts and seals to detach the governor. The installation procedure reverses these steps, replacing seals and using special tools to reattach connecting pins and tubes. Proper lubrication of seals and adjustment of fuel settings are emphasized.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation.
It also references other documents for additional governor information and maintenance guidelines.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...fujsefkksemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation.
It also references other documents for additional governor information and maintenance guidelines.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...ujfdjjkjskkemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel lines and cables, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new seals, and securing the governor with bolts while ensuring proper adjustment and movement of linkages. Special tools and calibration procedures are referenced for working on the governor and fuel control systems.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...ujfjjkskkemmd
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...fujsjefskekm
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation according to separate testing instructions.
It also includes instructions for removing the fuel injection control linkage by removing bolts and a clevis pin connecting it to the governor.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...ujdfjjkskkmmde
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with a list of required tools and safety notices. The removal procedure involves 11 steps that include disconnecting cables and tubes, removing clips and seals. The installation procedure reverses these steps, adding lubrication of new seals and adjustment of the fuel setting. Precise use of specialized tools is emphasized to properly position parts like the clevis pin and tube assembly.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...fujsefkxswksemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...fjjsefkksemme
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation according to separate testing instructions.
It also includes instructions for removing the fuel injection control linkage by removing bolts and a clevis pin connecting it to the governor.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...uufdjjdjfjkkskm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with removal steps such as disconnecting cables and tubes, and removing clips, pins, seals and bolts. Installation is the reverse of removal, applying new seals and lubricant before securing components with clips, pins and bolts. Special tools are required, and other manuals should be referenced for additional governor information. The overall procedure involves properly containing fluids, using the correct tools, and ensuring all connections are sealed.
Caterpillar cat 322 l excavator (prefix 8 ml) service repair manual (8ml00001...fjsjekksemm
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with removal steps such as disconnecting cables and tubes, and removing clips, pins, seals and bolts. Installation is the reverse of removal, applying new seals and lubricant and reconnecting all components. Special tools are required including governor pliers and pin pilots. References are provided for additional information on governor inspection and testing procedures.
Caterpillar cat 322 n excavator (prefix 8 ml) service repair manual (8ml00001...fjskekmsemmwe
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with removal steps such as disconnecting cables and tubes, and removing clips, pins, seals and bolts. Installation is the reverse of removal, applying new seals and lubricant before securing components with clips, pins and bolts. Special tools are required, and other manuals should be referenced for additional governor information. The overall procedure involves properly containing fluids, using the correct tools, and ensuring all connections are sealed.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
More Related Content
Similar to Caterpillar Cat 322 N EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Download.pdf
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel lines and cables, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new seals, and securing the governor with bolts while ensuring proper adjustment and movement of linkages. Special tools and calibration procedures are referenced for working on the governor and fuel control systems.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...ujfjjkskkemmd
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...fujsjefskekm
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation according to separate testing instructions.
It also includes instructions for removing the fuel injection control linkage by removing bolts and a clevis pin connecting it to the governor.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...ujdfjjkskkmmde
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with a list of required tools and safety notices. The removal procedure involves 11 steps that include disconnecting cables and tubes, removing clips and seals. The installation procedure reverses these steps, adding lubrication of new seals and adjustment of the fuel setting. Precise use of specialized tools is emphasized to properly position parts like the clevis pin and tube assembly.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...fujsefkxswksemm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
Caterpillar cat 322 l excavator (prefix 4 rm) service repair manual (4rm00001...fjjsefkksemme
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It describes:
1. Removing fuel and oil lines, clips, bolts and pins to detach the governor from the engine.
2. Installing new O-rings, attaching the governor to the engine with bolts and pins, and reconnecting fuel and oil lines.
3. Checking the fuel setting adjustment after installation according to separate testing instructions.
It also includes instructions for removing the fuel injection control linkage by removing bolts and a clevis pin connecting it to the governor.
Caterpillar cat 322 n excavator (prefix 4 rm) service repair manual (4rm00001...uufdjjdjfjkkskm
This document provides instructions for removing and installing a governor on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to access the governor. The installation procedure specifies cleaning and lubricating parts, installing new O-rings, and securing the governor with bolts and clips. Special tools and calibration are required to properly adjust the governor settings.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with removal steps such as disconnecting cables and tubes, and removing clips, pins, seals and bolts. Installation is the reverse of removal, applying new seals and lubricant before securing components with clips, pins and bolts. Special tools are required, and other manuals should be referenced for additional governor information. The overall procedure involves properly containing fluids, using the correct tools, and ensuring all connections are sealed.
Caterpillar cat 322 l excavator (prefix 8 ml) service repair manual (8ml00001...fjsjekksemm
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with removal steps such as disconnecting cables and tubes, and removing clips, pins, seals and bolts. Installation is the reverse of removal, applying new seals and lubricant and reconnecting all components. Special tools are required including governor pliers and pin pilots. References are provided for additional information on governor inspection and testing procedures.
Caterpillar cat 322 n excavator (prefix 8 ml) service repair manual (8ml00001...fjskekmsemmwe
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with removal steps such as disconnecting cables and tubes, and removing clips, pins, seals and bolts. Installation is the reverse of removal, applying new seals and lubricant before securing components with clips, pins and bolts. Special tools are required, and other manuals should be referenced for additional governor information. The overall procedure involves properly containing fluids, using the correct tools, and ensuring all connections are sealed.
Similar to Caterpillar Cat 322 N EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Download.pdf (10)
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for removing and installing various components of the rear power take-off (RPTO) and vibration damper on a 993K wheel loader. It describes in detail how to disassemble the RPTO by removing nuts, bearings, and gears. It then explains the reverse process to assemble the RPTO. Separate sections provide procedures for installing the RPTO and removing/installing the vibration damper and pulley, including the use of various tools. Detailed illustrations accompany each step.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K Wheel Loader. It describes removing 16 different components of the parking brake including pistons, springs, discs, plates, and housings. Detailed illustrations and torque specifications are provided for each step of disassembly and assembly. Tools required include a slide hammer, puller, driver group, link brackets, lever puller hoist, and sealant. Personnel safety warnings and proper procedures are noted throughout.
The document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the various components of the torque converter including removing housing bolts, gears, bearings, seals, and other parts. It then describes 26 steps for reassembling the torque converter components in reverse order, noting specific alignment and torque specifications. The overall document provides detailed technical instructions for maintenance personnel to fully disassemble and reassemble the machine's torque converter.
The document provides instructions for disassembling and assembling the service brake on a Caterpillar 993K wheel loader. The disassembly procedure involves removing reaction plates, discs, springs, pistons, seals and other brake components. The assembly procedure describes installing these components in reverse order and applying grease and torques as specified. Safety precautions are provided to prevent injury from spring forces.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing and removing fuel injection nozzles
- Disassembling and assembling the fuel ratio control
- Removing and installing the fuel shutoff solenoid
The instructions include diagrams illustrating the components and numbered steps for disassembly, cleaning, inspection, and reassembly of the parts. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the swing drive of a M325C MH wheeled excavator. It lists 31 steps for disassembly, removing components like the cover, carrier assembly, gears, shafts, and seals. It then lists 35 steps for assembly, installing these components in reverse order along with tools needed and special instructions. Precautions are given to contain fluids, clean parts thoroughly, and use lifting devices due to component weights up to 310 kg.
This document provides instructions for disassembling the front final drive, carrier, hubs, and brakes of an M320 Excavator. It outlines 28 steps to remove components like the planetary carrier, sun gear, ring gear, brake piston, hub, bearings and seals. Various tools are required including retaining ring pliers, pullers, wrenches and adapters. Safety notices are included about containing fluids, releasing hydraulic pressure and avoiding damage during disassembly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322 LN EXCAVATOR 4RM
Configuration: 322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 23:27:19 UTC+0800 2019
5/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322 LN EXCAVATOR 4RM
Configuration: 322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00673178
1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
Illustration 2 g00672733
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
Illustration 3 g00672742
3. Install the O-ring seal and tube assembly (5) in the cylinder head.
2/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g00673180
4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
Illustration 5 g00673182
5. Place the governor in position on the engine.
Illustration 6 g00613563
6. Install the washers and bolts (7) that hold the governor in place.
3/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g00672755
7. Install clevis pin (6) in Tooling (B).
Illustration 8 g00672752
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.
4/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 9 g00655975
10. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 10 g00613071
11. Install clip (4).
Illustration 11 g00613041
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 23:28:15 UTC+0800 2019
5/5
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322 LN EXCAVATOR 4RM
Configuration: 322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00613071
1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
Illustration 2 g00655975
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 3 g00613149
2/3
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
Illustration 4 g00630566
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 23:29:10 UTC+0800 2019
3/3
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322 LN EXCAVATOR 4RM
Configuration: 322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.
1/4
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00661331
Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
Illustration 2 g00750163
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".
2/4
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
Illustration 3 g00672755
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
Illustration 4 g00672752
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.
3/4
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 5 g00655975
14. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 6 g00613071
15. Install clip (4).
End By:
a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 23:30:06 UTC+0800 2019
4/4
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322 LN EXCAVATOR 4RM
Configuration: 322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i05919358
Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0302 Bar 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00775441
2/3
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
22. Illustration 2 g00625237
1. Remove fuel injector hold-down bolt (1) .
Note: Do not pry on the injector hold-down bracket. Damage to the unit injector could
occur. The unit injector has a notch on the opposite side of the rack. This notch is used for
prying the unit injector loose. Some fuel injector racks move freely when the spring is not
compressed. Do not move the fuel injector rack without compressing the fuel injector spring
slightly. Damage may occur to the unit injector.
2. Use Tooling (A) to loosen the unit injector. Rotate the unit injector in order to disengage
injector rack bar (3) from fuel injection control linkage (2) .
3. Remove the unit injector. Ensure that two O-ring seals are on the unit injector.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 16 23:31:02 UTC+0800 2019
3/3
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERE...
2019/10/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...