This document provides removal and installation procedures for components of the heating and air conditioning system on a 320E and 320E L excavator model. The procedures include removing and installing components like the air conditioner group, refrigerant receiver-dryer, actuator motors, and control module. Safety precautions are outlined, such as using protective equipment when working with refrigerant and not smoking in areas where refrigerant may be present. Detailed steps are accompanied by illustrations showing the component locations and part numbers.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides removal and installation instructions for removing and installing a radiator on a Caterpillar 527 Track Skidder. It describes removing guards, disconnecting hoses, removing bolts, and lifting out the radiator using lifting tools. The installation procedure reverses these steps, ensuring all connections are secure. Safety notices are provided regarding containing fluids, preventing contamination, and handling refrigerant.
The documents provide instructions for servicing components of a Caterpillar 3306 engine used in a 235 excavator, including:
1) Procedures for removing and installing the automatic timing advance, which involves aligning gears, removing bolts and plates, and using support tools.
2) Disassembling the automatic timing advance unit by removing screws, plates, springs, weights and seals.
3) Reassembling the automatic timing advance unit by installing seals, gears, slides, weights, springs and plates.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00455-00...fujskekdjdmd
The document provides instructions for servicing components of a 235 excavator, including removing, disassembling, and reassembling the boom speed control valve, track brake valve, boom vent valve, swing combiner and relief valve, and pump selector valve. Removal instructions involve disconnecting lines and removing mounting bolts. Disassembly involves removing internal components like springs, stems, and plugs. Reassembly follows the reverse order and ensures proper installation of seals and adjustment of clearance sizes.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, technicians must disconnect harness assemblies, tubes, and hoses after relieving fuel pressure and marking components.
3. Installation requires connecting new fuel lines and hoses according to illustrated steps while maintaining cleanliness to prevent contamination.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides removal and installation instructions for removing and installing a radiator on a Caterpillar 527 Track Skidder. It describes removing guards, disconnecting hoses, removing bolts, and lifting out the radiator using lifting tools. The installation procedure reverses these steps, ensuring all connections are secure. Safety notices are provided regarding containing fluids, preventing contamination, and handling refrigerant.
The documents provide instructions for servicing components of a Caterpillar 3306 engine used in a 235 excavator, including:
1) Procedures for removing and installing the automatic timing advance, which involves aligning gears, removing bolts and plates, and using support tools.
2) Disassembling the automatic timing advance unit by removing screws, plates, springs, weights and seals.
3) Reassembling the automatic timing advance unit by installing seals, gears, slides, weights, springs and plates.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00455-00...fujskekdjdmd
The document provides instructions for servicing components of a 235 excavator, including removing, disassembling, and reassembling the boom speed control valve, track brake valve, boom vent valve, swing combiner and relief valve, and pump selector valve. Removal instructions involve disconnecting lines and removing mounting bolts. Disassembly involves removing internal components like springs, stems, and plugs. Reassembly follows the reverse order and ensures proper installation of seals and adjustment of clearance sizes.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, technicians must disconnect harness assemblies, tubes, and hoses after relieving fuel pressure and marking components.
3. Installation requires connecting new fuel lines and hoses according to illustrated steps while maintaining cleanliness to prevent contamination.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings and pins, attaching lifting devices, tightening nuts and bolts, and connecting hoses and harnesses. Tools required include a driver, lever puller, and bearing installer. Safety precautions are provided for working on pressurized hydraulic systems.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3306 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Technicians are directed to clean parts, replace worn gaskets, and properly contain fluids during the repair process.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00596-01...fujskekdjdmd
This document provides instructions for removing and installing the automatic timing advance component from a Caterpillar 3306 engine. It describes:
- Removing the front housing before removing the timing advance
- Using turning tools to align marks on gears and position the #1 piston at top dead center
- Removing two plugs and installing a tool to view inside the flywheel housing
- Removing a bolt to take off the timing advance
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major system sections and lists parts for the engine mounting, engine hoses, air intake and exhaust piping, air cleaner piping, and air cleaner inner parts. The parts lists include part numbers, descriptions, and quantities.
This document provides instructions for removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid on a 322C and 322C L excavator powered by a 3126 engine. The removal and installation procedures include multiple illustrations and steps such as disconnecting tubes, removing bolts and filters, inspecting parts, lubricating components, and reinstalling parts. Safety notices are provided to keep components clean and contain fluids.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...fujskekdjdmd
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM350-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides a parts list for engine-related components of a HM350-1L machine with serial number A10001 or higher. It includes 20 main item categories from A to Y with numerous sub-items listed under each category. The parts list provides part numbers, descriptions, and other specifications for each item.
This document provides instructions for removing and installing final drive sprockets and travel brake valves on a 322-A excavator. It outlines the necessary safety procedures and gives step-by-step instructions for each job. To remove a final drive sprocket, tools must be installed under the frame and 16 bolts removed to lift the sprocket off. Travel brake valves are removed by releasing hydraulic pressure, disconnecting pipes, and removing 6 bolts. Detailed cleaning and installation steps are provided for both components.
Komatsu HM300-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides parts information for an HM300-1L machine with serial number range A10001-UP. It includes a list of major system sections and references to more detailed parts pages for the engine and its components. Parts are identified by number, description, and other specifications. The sections covered include the engine and its mounting, hoses, piping, harness, damper, air cleaner, and other related parts.
CASE 845B 845B DHP Motor Grader Service Repair Manual.pdffujskekdjdmd
This document provides technical specifications and descriptions of components for 667TA engines, including the engine block, crankshaft, connecting rod, piston, and camshaft. It describes the main features of each component as well as their functions within the engine. It also provides diagrams to illustrate the components.
Caterpillar Cat 322C L 322CL Excavator (Prefix FED) Service Repair Manual (FE...fujskekdjdmd
The document provides instructions for disassembling the pilot valve of a 322C excavator. It describes 27 steps to fully disassemble the pilot valve, removing components like fittings, seals, covers, springs, spools and plugs. Cleanliness is important during disassembly and identification marks should be made on components. Personal protective equipment is recommended when releasing spring forces during disassembly.
Caterpillar Cat 322C L 322CL Hydraulic Excavator (Prefix HEK) Service Repair ...fujskekdjdmd
This document provides instructions for removing and installing components on a 322C L Hydraulic Excavator including:
1. Removing and installing a unit injector hydraulic pump, which involves disconnecting lines and reconnecting a harness.
2. Removing a turbocharger by removing bolts, nuts and disconnecting tubes.
3. Disassembling a turbocharger by removing housings and waste gate.
4. Assembling a turbocharger by positioning housings and cartridge assembly and reconnecting tubes.
5. Removing an exhaust manifold by first removing the turbocharger, then removing bolts and nuts.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NDDC7000...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
This document provides instructions for removing and installing final drive sprockets and travel brake valves on a 322-A excavator. It describes using tools to support the sprocket and brake valve during removal to avoid injury. The steps include releasing hydraulic pressure, removing mounting bolts and hoisting out the heavy components. Reinstallation involves cleaning parts, checking seals, applying thread lock and torqueing fasteners to the specified values.
CASE 595SLE Loader Backhoe Service Repair Manual.pdffujskekdjdmd
This document provides instructions for removing and installing the engine and radiator on a Case loader backhoe. It describes removing identification tags from hoses and wires, raising the loader and installing a support strut, opening the hood, removing bolts and nuts from the hood pivot point, and having an assistant help remove retainers and lower the hood. Steps are provided for draining coolant, removing hoses and fans, removing mounting bolts, and lifting out the radiator or engine. Reinstallation follows the removal steps in reverse order.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NFDC7000...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NFC10100...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings and pins, attaching lifting devices, tightening nuts and bolts, and connecting hoses and harnesses. Tools required include a driver, lever puller, and bearing installer. Safety precautions are provided for working on pressurized hydraulic systems.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3306 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Technicians are directed to clean parts, replace worn gaskets, and properly contain fluids during the repair process.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00596-01...fujskekdjdmd
This document provides instructions for removing and installing the automatic timing advance component from a Caterpillar 3306 engine. It describes:
- Removing the front housing before removing the timing advance
- Using turning tools to align marks on gears and position the #1 piston at top dead center
- Removing two plugs and installing a tool to view inside the flywheel housing
- Removing a bolt to take off the timing advance
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major system sections and lists parts for the engine mounting, engine hoses, air intake and exhaust piping, air cleaner piping, and air cleaner inner parts. The parts lists include part numbers, descriptions, and quantities.
This document provides instructions for removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid on a 322C and 322C L excavator powered by a 3126 engine. The removal and installation procedures include multiple illustrations and steps such as disconnecting tubes, removing bolts and filters, inspecting parts, lubricating components, and reinstalling parts. Safety notices are provided to keep components clean and contain fluids.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...fujskekdjdmd
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM350-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides a parts list for engine-related components of a HM350-1L machine with serial number A10001 or higher. It includes 20 main item categories from A to Y with numerous sub-items listed under each category. The parts list provides part numbers, descriptions, and other specifications for each item.
This document provides instructions for removing and installing final drive sprockets and travel brake valves on a 322-A excavator. It outlines the necessary safety procedures and gives step-by-step instructions for each job. To remove a final drive sprocket, tools must be installed under the frame and 16 bolts removed to lift the sprocket off. Travel brake valves are removed by releasing hydraulic pressure, disconnecting pipes, and removing 6 bolts. Detailed cleaning and installation steps are provided for both components.
Komatsu HM300-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides parts information for an HM300-1L machine with serial number range A10001-UP. It includes a list of major system sections and references to more detailed parts pages for the engine and its components. Parts are identified by number, description, and other specifications. The sections covered include the engine and its mounting, hoses, piping, harness, damper, air cleaner, and other related parts.
CASE 845B 845B DHP Motor Grader Service Repair Manual.pdffujskekdjdmd
This document provides technical specifications and descriptions of components for 667TA engines, including the engine block, crankshaft, connecting rod, piston, and camshaft. It describes the main features of each component as well as their functions within the engine. It also provides diagrams to illustrate the components.
Caterpillar Cat 322C L 322CL Excavator (Prefix FED) Service Repair Manual (FE...fujskekdjdmd
The document provides instructions for disassembling the pilot valve of a 322C excavator. It describes 27 steps to fully disassemble the pilot valve, removing components like fittings, seals, covers, springs, spools and plugs. Cleanliness is important during disassembly and identification marks should be made on components. Personal protective equipment is recommended when releasing spring forces during disassembly.
Caterpillar Cat 322C L 322CL Hydraulic Excavator (Prefix HEK) Service Repair ...fujskekdjdmd
This document provides instructions for removing and installing components on a 322C L Hydraulic Excavator including:
1. Removing and installing a unit injector hydraulic pump, which involves disconnecting lines and reconnecting a harness.
2. Removing a turbocharger by removing bolts, nuts and disconnecting tubes.
3. Disassembling a turbocharger by removing housings and waste gate.
4. Assembling a turbocharger by positioning housings and cartridge assembly and reconnecting tubes.
5. Removing an exhaust manifold by first removing the turbocharger, then removing bolts and nuts.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NDDC7000...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
This document provides instructions for removing and installing final drive sprockets and travel brake valves on a 322-A excavator. It describes using tools to support the sprocket and brake valve during removal to avoid injury. The steps include releasing hydraulic pressure, removing mounting bolts and hoisting out the heavy components. Reinstallation involves cleaning parts, checking seals, applying thread lock and torqueing fasteners to the specified values.
CASE 595SLE Loader Backhoe Service Repair Manual.pdffujskekdjdmd
This document provides instructions for removing and installing the engine and radiator on a Case loader backhoe. It describes removing identification tags from hoses and wires, raising the loader and installing a support strut, opening the hood, removing bolts and nuts from the hood pivot point, and having an assistant help remove retainers and lower the hood. Steps are provided for draining coolant, removing hoses and fans, removing mounting bolts, and lifting out the radiator or engine. Reinstallation follows the removal steps in reverse order.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NFDC7000...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NFC10100...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04390499
Heating and Air Conditioning
SMCS - 7304; 7309; 7320
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 1. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a
Refrigerant" for the recovery and the charging procedure. Refer to Special Publication,
NENG2500, "Air Conditioning Tools" for the correct tools.
Illustration 1 g02561096
2. Disconnect hose assembly (3). Remove switch (2). Remove bolts (1).
Illustration 2 g02561097
3. Clamp hose, as shown to contain coolant. Remove hoses (4).
Illustration 3 g02561116
2/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 1. Install air conditioner group (21) in the reverse order of removal.
Disassembly Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be cleaned thoroughly. This will help to prevent dirt from entering the internal
mechanism.
Illustration 13 g02566678
1. Disconnect harness assembly (1). Remove actuator motor (2).
Illustration 14 g02566681
6/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 25 g02566681
4. Slide in core (6). Install cover (3). Install actuators motors (4). Connect harness assemblies
(5).
Illustration 26 g02566678
5. Install actuator motor (2). Connect harness assembly (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:24:18 UTC+0800 2019
10/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04384176
Refrigerant Receiver-Dryer
SMCS - 7322
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Recover the air conditioner refrigerant from the air conditioner system. Refer to ,
SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the
correct procedure. Refer to Dealer Service Tool Catalog, NENG2500, "Air Conditioning
Tools" for the correct tools.
Illustration 1 g02551740
2. Open the left side access door.
Illustration 2 g02551741
3. Disconnect lines (2) from the refrigerant dryer (3).
Illustration 3 g02551744
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 4. Remove clamps (4). Remove refrigerant dryer (3).
Installation Procedure
1. Install refrigerant dryer (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:25:14 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04604894
Actuator Motor (Air Distributor)
SMCS - 7304-MQ; 7309-MQ; 7320-MQ
Removal Procedure
Start By:
a. Remove the storage box and covers.
Illustration 1 g02412816
1. Remove bolts (1) and (3). Remove cover (2).
1/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g02412857
2. Remove cover (4).
Illustration 3 g02412877
3. Disconnect harness assembly (5). Remove screws (7). Remove actuator (6).
Installation Procedure
1. Install actuator (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:26:10 UTC+0800 2019
2/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04484309
Control Module (Automatic Temperature Control Unit)
SMCS - 7304-TA; 7309-TA; 7320-TA
Removal Procedure
Illustration 1 g02235393
1. Remove cover (1) and screw. Remove cover (2).
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g02237715
2. Remove screws (3) from control panel (4).
Illustration 3 g02238123
3. Disconnect harness assemblies (5), (6), (7), and (8).
Illustration 4 g02238193
4. Disconnect harness assemblies (9), (10), and (11).
Illustration 5 g02238234
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 5. Disconnect antenna (12). Disconnect harness assemblies (13), (14), (15), and (16).
6. Remove control module (4).
Installation Procedure
1. Install control panel (4) in the reverse order of the removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:27:06 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610611
Track Carrier Roller
SMCS - 4154
Specifications
Illustration 1 g02593236
Table 1
Specification for 8E-5600 Track Carrier Roller
Item Qty Part Specification Description
1 1
8E-5608
Duo-
Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean and
dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The metal
seal rings must be assembled square. The rubber toric seals should not
bulge and the rubber toric seals should not twist.
A - -
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. End play:
Minimum is 0.20 mm (0.008 inch).
Maximum is 0.75 mm (0.030 inch).
2 1
6V-7661
O-Ring
Seal
Lubricate the bore of the O-ring seal lightly with the lubricant that is
being sealed.
B - -
Before assembly, length of the track roller shaft assembly that must be
free of paint is 55 ± 5 mm (2.2 ± 0.2 inch).
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8T-5255 Hydraulic Jack 1
1. Start the engine. Park the machine on a hard, level surface. Shut off the engine.
Personal injury or death can result from grease and oil coming out of
the relief valve.
Grease and oil are under high pressure coming out of the relief valve
and can penetrate the body.
Do not watch the relief valve to see if grease is escaping. Watch the track
or track adjustment cylinder to see if the track is being loosened.
Make sure the vent holes are clean before the tension is released on the
track.
Illustration 2 g00489342
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 2. Release the tension on the track.
3. Loosen relief valve (1) by one turn only. If the track does not loosen after opening the relief
valve, move the machine forward and backward until the tension is released.
Illustration 3 g00693935
4. Loosen bolt (2) that holds track carrier roller (3) to the mounting bracket on the undercarriage.
Illustration 4 g00489356
5. Position Tooling (A) and suitable cribbing under the track assembly, as shown.
6. Use Tooling (A) in order to lift the track assembly off the track carrier roller.
7. Remove track carrier roller (3). The weight of track carrier roller (3) is 17 kg (38 lb).
Reference: Refer to Undercarriage Reconditioning Bulletin, SEBF8568, "Hydraulic Excavator Roller
Disassemble and Assembly Procedures" for the Disassembly and Assembly procedures for the track
carrier roller.
Installation Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. A 8T-5255 Hydraulic Jack 1
1. Make sure that the shaft of the track carrier roller and the bore in the mounting bracket on the
undercarriage are clean and free of dirt.
Illustration 5 g00652868
(x) Mounting bracket
2. Place the track carrier roller in position in the mounting bracket. The weight of track carrier
roller is 17 kg (38 lb). Adjust the carrier roller until Distance (a), the distance between the
outside face of the mounting bracket and the carrier roller is 7.0 ± 0.5 mm (0.28 ± 0.02 inch).
Illustration 6 g00693935
3. After you adjust the position of track carrier roller (3) in the mounting bracket, tighten bolt (2).
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 7 g00489356
4. Make sure that track carrier roller (3) rotates smoothly by manually turning the carrier roller.
5. Slowly lower the track assembly onto the carrier roller with Tooling (A).
6. Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:28:01 UTC+0800 2019
5/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610953
Track Roller
SMCS - 4180
Specifications
Illustration 1 g02724642
Table 1
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Specification for 348-1868 Double Flange Track Roller
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2 2
7F-8268 O
-Ring Seal Lubricate the bore with the lubricant that is being sealed.
3 2
9W-2142
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
7H-3171
Pipe Plug
Apply blue Loctite 242 to the threads.
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Illustration 2 g02724638
Table 2
Specification for 206-1265 Track Roller Gp
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 2 2 7F-8268 O
-Ring Seal
Lubricate the bore with the lubricant that is being sealed.
3 2
206-9211
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
9w-2146
Plug
Apply blue Loctite 242 to the threads.
Torque to 28 ± 5 N·m (248 ± 44 lb in).
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Removal Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Tube 2
8S-7615 Pin 2
8S-7640 Stand 2
B 183-4797 Track Roller Lifting Fork 1
Note: There is a track guide on each side of the machine. The procedure that follows is for the
removal of the track roller with the track guide.
1. Start the engine. Park the machine on a hard, level surface. Stop the engine.
2. Release the tension on the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust".
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 3 g01211423
Note: Adjust the height of Tooling (A) in order to have sufficient clearance for the removal of
the track rollers when Tooling (A) is installed under the undercarriage (1) of the machine.
3. Lift the side of the machine. Install Tooling (A) under the undercarriage, as shown.
Illustration 4 g00664654
4. Loosen the bolts that hold track guide (2) to the undercarriage.
Note: Do not remove the bolts at this time.
Illustration 5 g00664663
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...