This document provides removal and installation procedures for components of the heating and air conditioning system on a 320E and 320E L excavator model. The procedures include removing and installing components like the air conditioner group, refrigerant receiver-dryer, actuator motors, and control module. Safety precautions are outlined, such as using protective equipment when working with refrigerant and not smoking in areas where refrigerant may be present. Detailed steps are accompanied by illustrations showing the component locations and part numbers.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides removal and installation instructions for removing and installing a radiator on a Caterpillar 527 Track Skidder. It describes removing guards, disconnecting hoses, removing bolts, and lifting out the radiator using lifting tools. The installation procedure reverses these steps, ensuring all connections are secure. Safety notices are provided regarding containing fluids, preventing contamination, and handling refrigerant.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 422E backhoe loader with a 3054C engine, including the fuel priming pump, fuel filter base, fuel injection lines, fuel injection nozzles, and fuel injection pump. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order. Cautions are provided regarding containing fluids and preventing contamination. Required tools are listed for each job.
Caterpillar Cat E70 EXCAVATOR (Prefix 3BG) Service Repair Manual (3BG00001-UP...ufjskmdmdmed
This document provides instructions for properly installing Duo-Cone seals. It describes the components of Duo-Cone seals and outlines best practices for cleaning, handling, inspecting, and assembling the seals using the appropriate tooling. Critical areas like the seal ring face and housing ramp are to be carefully inspected for defects before installation to prevent leaks. Rubber seals and metal components must be kept free of contamination and lubricated during assembly.
This document provides instructions for removing and installing a radiator on a Caterpillar 906 Compact Wheel Loader. The removal procedure involves:
1. Draining the coolant and removing the radiator fill cap.
2. Removing mounting bolts and brackets to detach the radiator.
3. Using straps to lift out the radiator.
The installation procedure describes reinstalling the radiator using new gaskets and bolts, then refilling the cooling system. Safety precautions are provided to avoid burns from hot coolant and ensure fluids are contained.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides removal and installation instructions for removing and installing a radiator on a Caterpillar 527 Track Skidder. It describes removing guards, disconnecting hoses, removing bolts, and lifting out the radiator using lifting tools. The installation procedure reverses these steps, ensuring all connections are secure. Safety notices are provided regarding containing fluids, preventing contamination, and handling refrigerant.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 422E backhoe loader with a 3054C engine, including the fuel priming pump, fuel filter base, fuel injection lines, fuel injection nozzles, and fuel injection pump. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order. Cautions are provided regarding containing fluids and preventing contamination. Required tools are listed for each job.
Caterpillar Cat E70 EXCAVATOR (Prefix 3BG) Service Repair Manual (3BG00001-UP...ufjskmdmdmed
This document provides instructions for properly installing Duo-Cone seals. It describes the components of Duo-Cone seals and outlines best practices for cleaning, handling, inspecting, and assembling the seals using the appropriate tooling. Critical areas like the seal ring face and housing ramp are to be carefully inspected for defects before installation to prevent leaks. Rubber seals and metal components must be kept free of contamination and lubricated during assembly.
This document provides instructions for removing and installing a radiator on a Caterpillar 906 Compact Wheel Loader. The removal procedure involves:
1. Draining the coolant and removing the radiator fill cap.
2. Removing mounting bolts and brackets to detach the radiator.
3. Using straps to lift out the radiator.
The installation procedure describes reinstalling the radiator using new gaskets and bolts, then refilling the cooling system. Safety precautions are provided to avoid burns from hot coolant and ensure fluids are contained.
This document provides instructions for assembling an alternator. It describes 29 steps to assemble internal components like diodes, bushings, coils, and housings. Cleanliness is important during assembly to avoid issues. Diodes and bearings should not be struck as it can damage them. Dielectric grease should be applied where noted. The final steps include installing external components like the mounting plate, regulator, and cover.
This document provides instructions for assembling a Type I governor used on 3114, 3116, and 3126 engines. It describes 19 steps to assemble components like the drive gear, C spring, fuel ratio control lever, output servo, bearing block, and torque cam. Tools required include a governor repair fixture, clevis driver, servo block, pin punch, and torque adjusting tool. Proper positioning and clearance of parts is important for correct governor function.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...ufjskmdmdmed
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 527 Track Skidder with a 3304 engine. The procedures include removing bolts and hoses, checking gaskets, applying fuel to seals during installation, and ensuring parts are clean to prevent contamination. Illustrations show the component locations and part numbers.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings, pins, bolts and other components onto the swing frame assembly and attaching hydraulic hoses and electrical harnesses. Tools required include a driver, lever puller, and bearing installer. Precautions are provided for safely releasing hydraulic pressure before removing any components.
This document provides instructions to disassemble a bank valve on a 420E Backhoe Loader. The 19 step procedure includes removing manifolds, valves, spools, cartridges, seals, springs and covers. Special care must be taken when removing parts under spring pressure to avoid injury.
This document provides instructions for disassembling and assembling the steering metering pump on a 428D Backhoe Loader. The removal procedure involves removing covers, plates, bolts and nuts to access the steering column. Disassembly involves removing an end cap, seals, housing components, drive components, springs and fittings. Assembly is the reverse of disassembly, applying new seals and lubricating components before installation. Cleanliness is important during disassembly and assembly to prevent contaminating the hydraulic system.
The document provides instructions for disassembling the transmission of a 428D backhoe loader in 3 steps:
1. Remove the transmission and drain the oil.
2. Disassemble the transmission into its major components like the case, output shafts, and gears.
3. Further disassemble the components using various tools, removing items like bearings, seals, springs, and shafts. Detailed illustrations are provided to identify specific parts.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. Removal involves draining fuel, removing retaining components, and plugging lines. Installation requires cleaning, adding new seals, and reinstalling components in reverse order of removal while torquing fasteners to specified values. Disassembly of the governor/camshaft involves using tools to separate the sleeve, retaining ring, and bearing from the camshaft.
The document provides instructions for removing and installing various components of a Caterpillar C2.4 Tier 4 Final engine, including:
- Removing and installing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing and installing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing and installing the turbocharger by removing intake hoses and disconnecting pipes.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader powered by a C2.4 engine. It includes procedures for removing and installing fuel injection lines and nozzles, and removing, disassembling, and reassembling the governor and camshaft. Detailed illustrations accompany each step-by-step procedure to ensure correct part placement and tool usage. Technicians are advised to keep components clean and plug all openings to prevent contamination.
Caterpillar Cat 322C L 322CL Hydraulic Excavator (Prefix HEK) Service Repair ...ufjskmdmdmed
This document provides instructions for servicing components of a Caterpillar 3126B engine, including:
- Installing a unit injector hydraulic pump by positioning components, lubricating seals, and tightening bolts.
- Removing a turbocharger by removing bolts, nuts, and tubes connecting it to other components.
- Disassembling a turbocharger by removing housings, gates, and marking components for alignment during reassembly.
- Reassembling a turbocharger by positioning components, connecting tubes, and installing gates according to alignment marks.
- Removing and installing an exhaust manifold by removing bolts and gaskets, applying sealant, and tightening bolts
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdfufjskmdmdmed
This document provides instructions for removing and installing an alternator, fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar D4E track-type tractor with a 3304 engine. The alternator disassembly procedure involves removing components like the pulley, fan, bearings, and stator. The assembly procedure describes cleaning and reinstalling these parts. Instructions are also given for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump, which involve disconnecting lines and removing mounting bolts.
Caterpillar Cat 322C L 322CL Excavator (Prefix FED) Service Repair Manual (FE...ufjskmdmdmed
The document provides instructions for disassembling the pilot valve of a 322C excavator. It describes 27 steps to fully disassemble the pilot valve, removing components like fittings, seals, covers, springs, spools and plugs. Cleanliness is important during disassembly and identification marks should be made on components. Personal protective equipment is recommended when releasing spring forces during disassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
This document provides instructions for assembling a Type I governor used on 3114, 3116, and 3126 engines. It describes 19 steps to assemble components like the drive gear, C spring, fuel ratio control lever, output servo, bearing block, and torque cam. Tools required include a governor repair fixture, clevis driver, servo block, pin punch, and torque adjusting tool. Proper positioning and clearance of parts is important for correct governor function.
This document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators. It describes the parts and tools needed and steps to disassemble three starting motor models: 42-MT, 37-MT, and 41-MT. The instructions cover removing components like the rear housing, brushes, pinion drive, shift lever housing, and field winding coil. Cleaning and inspection steps are also included. The goal is to repair or replace worn parts to restore the starting motors to working condition.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...ufjskmdmdmed
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It includes the following procedures:
1. Removing the crankshaft vibration damper and pulley.
2. Removing and installing the crankshaft front seal.
3. Removing and installing the front cover.
4. Removing the front housing by taking off the front engine support, belt tightener, and front housing.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a 527 Track Skidder with a 3304 engine. The procedures include removing bolts and hoses, checking gaskets, applying fuel to seals during installation, and ensuring parts are clean to prevent contamination. Illustrations show the component locations and part numbers.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings, pins, bolts and other components onto the swing frame assembly and attaching hydraulic hoses and electrical harnesses. Tools required include a driver, lever puller, and bearing installer. Precautions are provided for safely releasing hydraulic pressure before removing any components.
This document provides instructions to disassemble a bank valve on a 420E Backhoe Loader. The 19 step procedure includes removing manifolds, valves, spools, cartridges, seals, springs and covers. Special care must be taken when removing parts under spring pressure to avoid injury.
This document provides instructions for disassembling and assembling the steering metering pump on a 428D Backhoe Loader. The removal procedure involves removing covers, plates, bolts and nuts to access the steering column. Disassembly involves removing an end cap, seals, housing components, drive components, springs and fittings. Assembly is the reverse of disassembly, applying new seals and lubricating components before installation. Cleanliness is important during disassembly and assembly to prevent contaminating the hydraulic system.
The document provides instructions for disassembling the transmission of a 428D backhoe loader in 3 steps:
1. Remove the transmission and drain the oil.
2. Disassemble the transmission into its major components like the case, output shafts, and gears.
3. Further disassemble the components using various tools, removing items like bearings, seals, springs, and shafts. Detailed illustrations are provided to identify specific parts.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. Removal involves draining fuel, removing retaining components, and plugging lines. Installation requires cleaning, adding new seals, and reinstalling components in reverse order of removal while torquing fasteners to specified values. Disassembly of the governor/camshaft involves using tools to separate the sleeve, retaining ring, and bearing from the camshaft.
The document provides instructions for removing and installing various components of a Caterpillar C2.4 Tier 4 Final engine, including:
- Removing and installing the fuel manifold by removing bolts and disconnecting fuel injection lines.
- Removing and installing fuel injection lines by disconnecting hoses and removing clamps and bolts.
- Removing and installing the turbocharger by removing intake hoses and disconnecting pipes.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader powered by a C2.4 engine. It includes procedures for removing and installing fuel injection lines and nozzles, and removing, disassembling, and reassembling the governor and camshaft. Detailed illustrations accompany each step-by-step procedure to ensure correct part placement and tool usage. Technicians are advised to keep components clean and plug all openings to prevent contamination.
Caterpillar Cat 322C L 322CL Hydraulic Excavator (Prefix HEK) Service Repair ...ufjskmdmdmed
This document provides instructions for servicing components of a Caterpillar 3126B engine, including:
- Installing a unit injector hydraulic pump by positioning components, lubricating seals, and tightening bolts.
- Removing a turbocharger by removing bolts, nuts, and tubes connecting it to other components.
- Disassembling a turbocharger by removing housings, gates, and marking components for alignment during reassembly.
- Reassembling a turbocharger by positioning components, connecting tubes, and installing gates according to alignment marks.
- Removing and installing an exhaust manifold by removing bolts and gaskets, applying sealant, and tightening bolts
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdfufjskmdmdmed
This document provides instructions for removing and installing an alternator, fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar D4E track-type tractor with a 3304 engine. The alternator disassembly procedure involves removing components like the pulley, fan, bearings, and stator. The assembly procedure describes cleaning and reinstalling these parts. Instructions are also given for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump, which involve disconnecting lines and removing mounting bolts.
Caterpillar Cat 322C L 322CL Excavator (Prefix FED) Service Repair Manual (FE...ufjskmdmdmed
The document provides instructions for disassembling the pilot valve of a 322C excavator. It describes 27 steps to fully disassemble the pilot valve, removing components like fittings, seals, covers, springs, spools and plugs. Cleanliness is important during disassembly and identification marks should be made on components. Personal protective equipment is recommended when releasing spring forces during disassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04390499
Heating and Air Conditioning
SMCS - 7304; 7309; 7320
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 1. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a
Refrigerant" for the recovery and the charging procedure. Refer to Special Publication,
NENG2500, "Air Conditioning Tools" for the correct tools.
Illustration 1 g02561096
2. Disconnect hose assembly (3). Remove switch (2). Remove bolts (1).
Illustration 2 g02561097
3. Clamp hose, as shown to contain coolant. Remove hoses (4).
Illustration 3 g02561116
2/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 1. Install air conditioner group (21) in the reverse order of removal.
Disassembly Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be cleaned thoroughly. This will help to prevent dirt from entering the internal
mechanism.
Illustration 13 g02566678
1. Disconnect harness assembly (1). Remove actuator motor (2).
Illustration 14 g02566681
6/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 25 g02566681
4. Slide in core (6). Install cover (3). Install actuators motors (4). Connect harness assemblies
(5).
Illustration 26 g02566678
5. Install actuator motor (2). Connect harness assembly (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:24:18 UTC+0800 2019
10/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04384176
Refrigerant Receiver-Dryer
SMCS - 7322
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Recover the air conditioner refrigerant from the air conditioner system. Refer to ,
SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the
correct procedure. Refer to Dealer Service Tool Catalog, NENG2500, "Air Conditioning
Tools" for the correct tools.
Illustration 1 g02551740
2. Open the left side access door.
Illustration 2 g02551741
3. Disconnect lines (2) from the refrigerant dryer (3).
Illustration 3 g02551744
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 4. Remove clamps (4). Remove refrigerant dryer (3).
Installation Procedure
1. Install refrigerant dryer (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:25:14 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04604894
Actuator Motor (Air Distributor)
SMCS - 7304-MQ; 7309-MQ; 7320-MQ
Removal Procedure
Start By:
a. Remove the storage box and covers.
Illustration 1 g02412816
1. Remove bolts (1) and (3). Remove cover (2).
1/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g02412857
2. Remove cover (4).
Illustration 3 g02412877
3. Disconnect harness assembly (5). Remove screws (7). Remove actuator (6).
Installation Procedure
1. Install actuator (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:26:10 UTC+0800 2019
2/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04484309
Control Module (Automatic Temperature Control Unit)
SMCS - 7304-TA; 7309-TA; 7320-TA
Removal Procedure
Illustration 1 g02235393
1. Remove cover (1) and screw. Remove cover (2).
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g02237715
2. Remove screws (3) from control panel (4).
Illustration 3 g02238123
3. Disconnect harness assemblies (5), (6), (7), and (8).
Illustration 4 g02238193
4. Disconnect harness assemblies (9), (10), and (11).
Illustration 5 g02238234
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 5. Disconnect antenna (12). Disconnect harness assemblies (13), (14), (15), and (16).
6. Remove control module (4).
Installation Procedure
1. Install control panel (4) in the reverse order of the removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:27:06 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610611
Track Carrier Roller
SMCS - 4154
Specifications
Illustration 1 g02593236
Table 1
Specification for 8E-5600 Track Carrier Roller
Item Qty Part Specification Description
1 1
8E-5608
Duo-
Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean and
dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The metal
seal rings must be assembled square. The rubber toric seals should not
bulge and the rubber toric seals should not twist.
A - -
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. End play:
Minimum is 0.20 mm (0.008 inch).
Maximum is 0.75 mm (0.030 inch).
2 1
6V-7661
O-Ring
Seal
Lubricate the bore of the O-ring seal lightly with the lubricant that is
being sealed.
B - -
Before assembly, length of the track roller shaft assembly that must be
free of paint is 55 ± 5 mm (2.2 ± 0.2 inch).
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8T-5255 Hydraulic Jack 1
1. Start the engine. Park the machine on a hard, level surface. Shut off the engine.
Personal injury or death can result from grease and oil coming out of
the relief valve.
Grease and oil are under high pressure coming out of the relief valve
and can penetrate the body.
Do not watch the relief valve to see if grease is escaping. Watch the track
or track adjustment cylinder to see if the track is being loosened.
Make sure the vent holes are clean before the tension is released on the
track.
Illustration 2 g00489342
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 2. Release the tension on the track.
3. Loosen relief valve (1) by one turn only. If the track does not loosen after opening the relief
valve, move the machine forward and backward until the tension is released.
Illustration 3 g00693935
4. Loosen bolt (2) that holds track carrier roller (3) to the mounting bracket on the undercarriage.
Illustration 4 g00489356
5. Position Tooling (A) and suitable cribbing under the track assembly, as shown.
6. Use Tooling (A) in order to lift the track assembly off the track carrier roller.
7. Remove track carrier roller (3). The weight of track carrier roller (3) is 17 kg (38 lb).
Reference: Refer to Undercarriage Reconditioning Bulletin, SEBF8568, "Hydraulic Excavator Roller
Disassemble and Assembly Procedures" for the Disassembly and Assembly procedures for the track
carrier roller.
Installation Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. A 8T-5255 Hydraulic Jack 1
1. Make sure that the shaft of the track carrier roller and the bore in the mounting bracket on the
undercarriage are clean and free of dirt.
Illustration 5 g00652868
(x) Mounting bracket
2. Place the track carrier roller in position in the mounting bracket. The weight of track carrier
roller is 17 kg (38 lb). Adjust the carrier roller until Distance (a), the distance between the
outside face of the mounting bracket and the carrier roller is 7.0 ± 0.5 mm (0.28 ± 0.02 inch).
Illustration 6 g00693935
3. After you adjust the position of track carrier roller (3) in the mounting bracket, tighten bolt (2).
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 7 g00489356
4. Make sure that track carrier roller (3) rotates smoothly by manually turning the carrier roller.
5. Slowly lower the track assembly onto the carrier roller with Tooling (A).
6. Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:28:01 UTC+0800 2019
5/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610953
Track Roller
SMCS - 4180
Specifications
Illustration 1 g02724642
Table 1
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Specification for 348-1868 Double Flange Track Roller
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2 2
7F-8268 O
-Ring Seal Lubricate the bore with the lubricant that is being sealed.
3 2
9W-2142
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
7H-3171
Pipe Plug
Apply blue Loctite 242 to the threads.
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Illustration 2 g02724638
Table 2
Specification for 206-1265 Track Roller Gp
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 2 2 7F-8268 O
-Ring Seal
Lubricate the bore with the lubricant that is being sealed.
3 2
206-9211
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
9w-2146
Plug
Apply blue Loctite 242 to the threads.
Torque to 28 ± 5 N·m (248 ± 44 lb in).
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Removal Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Tube 2
8S-7615 Pin 2
8S-7640 Stand 2
B 183-4797 Track Roller Lifting Fork 1
Note: There is a track guide on each side of the machine. The procedure that follows is for the
removal of the track roller with the track guide.
1. Start the engine. Park the machine on a hard, level surface. Stop the engine.
2. Release the tension on the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust".
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 3 g01211423
Note: Adjust the height of Tooling (A) in order to have sufficient clearance for the removal of
the track rollers when Tooling (A) is installed under the undercarriage (1) of the machine.
3. Lift the side of the machine. Install Tooling (A) under the undercarriage, as shown.
Illustration 4 g00664654
4. Loosen the bolts that hold track guide (2) to the undercarriage.
Note: Do not remove the bolts at this time.
Illustration 5 g00664663
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...