This document provides removal and installation procedures for components of the heating and air conditioning system on a 320E and 320E L excavator model. The procedures include removing the air conditioner group, refrigerant receiver-dryer, actuator motors, and control module. Safety precautions are outlined, such as using protective equipment when working with refrigerant and not smoking in areas where refrigerant may be present. Detailed steps are described and accompanied by illustrations showing the component locations and part numbers.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides removal and installation instructions for removing and installing a radiator on a Caterpillar 527 Track Skidder. It describes removing guards, disconnecting hoses, removing bolts, and lifting out the radiator using lifting tools. The installation procedure reverses these steps, ensuring all connections are secure. Safety notices are provided regarding containing fluids, preventing contamination, and handling refrigerant.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides removal and installation instructions for removing and installing a radiator on a Caterpillar 527 Track Skidder. It describes removing guards, disconnecting hoses, removing bolts, and lifting out the radiator using lifting tools. The installation procedure reverses these steps, ensuring all connections are secure. Safety notices are provided regarding containing fluids, preventing contamination, and handling refrigerant.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, sun gears, and housing. Special precautions are mentioned regarding lifting heavy parts safely and using locking compounds on threaded fasteners. The overall procedure involves removing parts in the reverse order they were installed.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 420E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard and remove bolts to lower the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening new bolts, then raising the guard back into place.
Caterpillar Cat 374F L Excavator (Prefix NFJ) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and presents 37 steps to disassemble the various components of the final drive, including removing the ring gear, carrier assemblies, sun gears, and housing components. The assembly section lists 2 steps, including cleaning all parts and reassembling the final drive while applying anti-seize compound to bearing surfaces. Safety notes warn about ensuring puller studs meet hydraulic cylinder capacity when used.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, sun gears, and housing. Special precautions are mentioned regarding lifting heavy parts safely and using locking compounds on threaded fasteners. The overall procedure involves removing parts in the reverse order they were installed.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 420E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard and remove bolts to lower the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening new bolts, then raising the guard back into place.
Caterpillar Cat 374F L Excavator (Prefix NFJ) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and presents 37 steps to disassemble the various components of the final drive, including removing the ring gear, carrier assemblies, sun gears, and housing components. The assembly section lists 2 steps, including cleaning all parts and reassembling the final drive while applying anti-seize compound to bearing surfaces. Safety notes warn about ensuring puller studs meet hydraulic cylinder capacity when used.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04390499
Heating and Air Conditioning
SMCS - 7304; 7309; 7320
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 1. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a
Refrigerant" for the recovery and the charging procedure. Refer to Special Publication,
NENG2500, "Air Conditioning Tools" for the correct tools.
Illustration 1 g02561096
2. Disconnect hose assembly (3). Remove switch (2). Remove bolts (1).
Illustration 2 g02561097
3. Clamp hose, as shown to contain coolant. Remove hoses (4).
Illustration 3 g02561116
2/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 1. Install air conditioner group (21) in the reverse order of removal.
Disassembly Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be cleaned thoroughly. This will help to prevent dirt from entering the internal
mechanism.
Illustration 13 g02566678
1. Disconnect harness assembly (1). Remove actuator motor (2).
Illustration 14 g02566681
6/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 25 g02566681
4. Slide in core (6). Install cover (3). Install actuators motors (4). Connect harness assemblies
(5).
Illustration 26 g02566678
5. Install actuator motor (2). Connect harness assembly (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:24:18 UTC+0800 2019
10/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04384176
Refrigerant Receiver-Dryer
SMCS - 7322
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Recover the air conditioner refrigerant from the air conditioner system. Refer to ,
SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the
correct procedure. Refer to Dealer Service Tool Catalog, NENG2500, "Air Conditioning
Tools" for the correct tools.
Illustration 1 g02551740
2. Open the left side access door.
Illustration 2 g02551741
3. Disconnect lines (2) from the refrigerant dryer (3).
Illustration 3 g02551744
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 4. Remove clamps (4). Remove refrigerant dryer (3).
Installation Procedure
1. Install refrigerant dryer (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:25:14 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04604894
Actuator Motor (Air Distributor)
SMCS - 7304-MQ; 7309-MQ; 7320-MQ
Removal Procedure
Start By:
a. Remove the storage box and covers.
Illustration 1 g02412816
1. Remove bolts (1) and (3). Remove cover (2).
1/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g02412857
2. Remove cover (4).
Illustration 3 g02412877
3. Disconnect harness assembly (5). Remove screws (7). Remove actuator (6).
Installation Procedure
1. Install actuator (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:26:10 UTC+0800 2019
2/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04484309
Control Module (Automatic Temperature Control Unit)
SMCS - 7304-TA; 7309-TA; 7320-TA
Removal Procedure
Illustration 1 g02235393
1. Remove cover (1) and screw. Remove cover (2).
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g02237715
2. Remove screws (3) from control panel (4).
Illustration 3 g02238123
3. Disconnect harness assemblies (5), (6), (7), and (8).
Illustration 4 g02238193
4. Disconnect harness assemblies (9), (10), and (11).
Illustration 5 g02238234
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 5. Disconnect antenna (12). Disconnect harness assemblies (13), (14), (15), and (16).
6. Remove control module (4).
Installation Procedure
1. Install control panel (4) in the reverse order of the removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:27:06 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610611
Track Carrier Roller
SMCS - 4154
Specifications
Illustration 1 g02593236
Table 1
Specification for 8E-5600 Track Carrier Roller
Item Qty Part Specification Description
1 1
8E-5608
Duo-
Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean and
dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The metal
seal rings must be assembled square. The rubber toric seals should not
bulge and the rubber toric seals should not twist.
A - -
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. End play:
Minimum is 0.20 mm (0.008 inch).
Maximum is 0.75 mm (0.030 inch).
2 1
6V-7661
O-Ring
Seal
Lubricate the bore of the O-ring seal lightly with the lubricant that is
being sealed.
B - -
Before assembly, length of the track roller shaft assembly that must be
free of paint is 55 ± 5 mm (2.2 ± 0.2 inch).
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8T-5255 Hydraulic Jack 1
1. Start the engine. Park the machine on a hard, level surface. Shut off the engine.
Personal injury or death can result from grease and oil coming out of
the relief valve.
Grease and oil are under high pressure coming out of the relief valve
and can penetrate the body.
Do not watch the relief valve to see if grease is escaping. Watch the track
or track adjustment cylinder to see if the track is being loosened.
Make sure the vent holes are clean before the tension is released on the
track.
Illustration 2 g00489342
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 2. Release the tension on the track.
3. Loosen relief valve (1) by one turn only. If the track does not loosen after opening the relief
valve, move the machine forward and backward until the tension is released.
Illustration 3 g00693935
4. Loosen bolt (2) that holds track carrier roller (3) to the mounting bracket on the undercarriage.
Illustration 4 g00489356
5. Position Tooling (A) and suitable cribbing under the track assembly, as shown.
6. Use Tooling (A) in order to lift the track assembly off the track carrier roller.
7. Remove track carrier roller (3). The weight of track carrier roller (3) is 17 kg (38 lb).
Reference: Refer to Undercarriage Reconditioning Bulletin, SEBF8568, "Hydraulic Excavator Roller
Disassemble and Assembly Procedures" for the Disassembly and Assembly procedures for the track
carrier roller.
Installation Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. A 8T-5255 Hydraulic Jack 1
1. Make sure that the shaft of the track carrier roller and the bore in the mounting bracket on the
undercarriage are clean and free of dirt.
Illustration 5 g00652868
(x) Mounting bracket
2. Place the track carrier roller in position in the mounting bracket. The weight of track carrier
roller is 17 kg (38 lb). Adjust the carrier roller until Distance (a), the distance between the
outside face of the mounting bracket and the carrier roller is 7.0 ± 0.5 mm (0.28 ± 0.02 inch).
Illustration 6 g00693935
3. After you adjust the position of track carrier roller (3) in the mounting bracket, tighten bolt (2).
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 7 g00489356
4. Make sure that track carrier roller (3) rotates smoothly by manually turning the carrier roller.
5. Slowly lower the track assembly onto the carrier roller with Tooling (A).
6. Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:28:01 UTC+0800 2019
5/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610953
Track Roller
SMCS - 4180
Specifications
Illustration 1 g02724642
Table 1
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Specification for 348-1868 Double Flange Track Roller
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2 2
7F-8268 O
-Ring Seal Lubricate the bore with the lubricant that is being sealed.
3 2
9W-2142
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
7H-3171
Pipe Plug
Apply blue Loctite 242 to the threads.
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Illustration 2 g02724638
Table 2
Specification for 206-1265 Track Roller Gp
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 2 2 7F-8268 O
-Ring Seal
Lubricate the bore with the lubricant that is being sealed.
3 2
206-9211
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
9w-2146
Plug
Apply blue Loctite 242 to the threads.
Torque to 28 ± 5 N·m (248 ± 44 lb in).
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Removal Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Tube 2
8S-7615 Pin 2
8S-7640 Stand 2
B 183-4797 Track Roller Lifting Fork 1
Note: There is a track guide on each side of the machine. The procedure that follows is for the
removal of the track roller with the track guide.
1. Start the engine. Park the machine on a hard, level surface. Stop the engine.
2. Release the tension on the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust".
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
29. Illustration 3 g01211423
Note: Adjust the height of Tooling (A) in order to have sufficient clearance for the removal of
the track rollers when Tooling (A) is installed under the undercarriage (1) of the machine.
3. Lift the side of the machine. Install Tooling (A) under the undercarriage, as shown.
Illustration 4 g00664654
4. Loosen the bolts that hold track guide (2) to the undercarriage.
Note: Do not remove the bolts at this time.
Illustration 5 g00664663
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...