This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. The procedure involves releasing hydraulic pressure, removing attachment points, and using lifting devices to maneuver the heavy cylinder. Special tools are required to remove pins connecting the cylinder. Torque specifications are provided for reinstallation. Safety precautions are described, such as relieving pressure before disassembly to avoid injury.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing components in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of seals is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before assembly and replacing any worn or damaged components.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 352F-VG Excavator (Prefix YEG) Service Repair Manual (YEG0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator model. It begins by listing the required tools and parts. The disassembly instructions describe 32 steps to remove components like plugs, seals, springs, pistons, plates and bearings from the motor. Precautions are provided for parts under spring tension. The assembly section lists specifications for installing 11 components, including torques and seals. Proper lubrication of parts is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing components in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of seals is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before assembly and replacing any worn or damaged components.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 352F-VG Excavator (Prefix YEG) Service Repair Manual (YEG0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator model. It begins by listing the required tools and parts. The disassembly instructions describe 32 steps to remove components like plugs, seals, springs, pistons, plates and bearings from the motor. Precautions are provided for parts under spring tension. The assembly section lists specifications for installing 11 components, including torques and seals. Proper lubrication of parts is emphasized before reassembly.
This document provides instructions for disassembling and assembling the final drive of a 365B excavator. The disassembly procedure involves removing 31 parts from the final drive housing using various tools. The assembly procedure specifies 34 steps, including cleaning parts, applying lubricants, setting bearing preloads using shims, and installing seals using special tools. Proper cleaning and lubrication of parts is emphasized throughout.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR DHK
Configuration: 320D & 320D L Excavators DHK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320D Excavator Machine Systems
Media Number -RENR8614-14 Publication Date -01/05/2013 Date Updated -19/07/2017
i07316669
Boom Cylinder - Remove and Install
SMCS - 5456-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9485 Pin Driver Cap 1
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Fully extend the bucket cylinder. Fully extend the stick cylinder. Lower the boom until the
stick assembly is in contact with the ground.
2. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Illustration 1 g01217839
Illustration 2 g01217840
3. Loosen nut (1). Turn bolt (2) counterclockwise to release the pressure in the cylinder.
2/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g01217850
4. Remove bolts (3).
Illustration 4 g01217906
5. Remove clamps (4).
Illustration 5 g01217908
6. Remove bolts (6) and support assemblies (5).
3/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 6 g01217912
7. Remove bolts (7) and reposition tube assembly (8) out of the way.
Illustration 7 g01217915
8. Remove bolts (9) and reposition valve assembly (10) out of the way.
Illustration 8 g01217921
9. Attach a suitable lifting device to boom cylinder (11). The weight of boom cylinder (11) is
approximately 287 kg (632 lb).
4/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g01217928
10. Remove bolts (12) and plate (13). Remove spacer (14) (not shown).
Illustration 10 g01218003
Illustration 11 g01218010
11. Attach Tooling (A) to pin (15). Use a suitable driver to reposition pin (15). Remove shim (16).
5/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 12 g01218011
12. Lower boom cylinder (11) onto suitable cribbing and attach a suitable lifting device to boom
cylinder (11), as shown. The weight of boom cylinder (11) is approximately 287 kg (632 lb).
Illustration 13 g01218013
13. Remove bolt (18). Remove pin assembly (19) and shims (17). Remove boom cylinder (11).
Disassembly and Assembly Information
Table 2
Required Tools
Tool Part Number Part Description Qty
B 127-4904 Hydraulic Cylinder Repair Stand Gp 1
C 7M-7456 Bearing Mount Compound 1
D 1P-0808 Multipurpose Grease 1
E 195-4609 Seal Pick 1
F 3S-6224 Electric Hydraulic Pump Gp 1
6V-3175 Double Acting Cylinder 1
9S-5564 Pin Puller Sleeve As 1
6/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 9U-6832 Nut 1
4C-9634 Puller Stud 1
9U-5338 Bearing Puller Adapter 1
G
3S-6224 Electric Hydraulic Pump Gp 1
6V-3175 Double Acting Cylinder 1
9S-5564 Pin Puller Sleeve As 1
9U-6832 Nut 1
4C-9634 Puller Stud 1
9U-5339 Bearing Puller Adapter 1
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
Illustration 14 g01218033
Note: Tooling (F) is used for the removal and installation of bearing (8). Tooling (G) is used for the
removal and installation of bearing (2).
Refer to Table 3 for the correct torque specification for piston (3).
Refer to Table 3 for the correct torque specification for bolts (1).
Table 3
Torque Table
7/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Piston or
Lock Nut
Piston / Lock Nut
Thread Size
Piston / Lock Nut (3) Torque
Specification
Head Bolts (1) Torque
Specification
Lock Nut M64
5900 ± 300 N·m
(4352 ± 221 lb ft)
460 ± 60 N·m
(339 ± 44 lb ft)
Piston M65
5460 ± 260 N·m
(4027 ± 192 lb ft)
267 ± 40 N·m
(197 2 ± 30 lb ft)
Lock Nut M72
7400 ± 370 N·m
(5458 ± 273 lb ft)
460 ± 60 N·m
(339 ± 44 lb ft)
Piston M75
7890 ± 395 N·m
(5819 ± 291 lb ft)
367 ± 55 N·m
(270 ± 40 lb ft)
Piston M80
8900 ± 445 N·m
(6564 ± 328 lb ft)
367 ± 55 N·m
(270 ± 40 lb ft)
Lock Nut M80
7900 ± 400 N·m
(5827 ± 295 lb ft)
800 ± 100 N·m
(590 ± 74 lb ft)
Piston M85
10000 ± 500 N·m
(7376 ± 368 lb ft)
520 ± 78 N·m
(384 ± 58 lb ft)
Piston and
Lock Nut
Piston is M75
980 to 1176 N·m
(722 to 867 lb ft) 333 to 352 N·m
(245 to 260 lb ft)
Lock Nut is M62
1862 to 1960 N·m
(1373 to 1446 lb ft)
Tighten the setscrew that retains nut (3) to a torque of 57 ± 11 N·m (42 ± 8 lb ft).
The slit of ring (5) must be in the direction of the piston.
Apply Tooling (D) to seals (4) prior to assembly.
Lubricate seals (6) with the lubricant that is being sealed.
Apply Tooling (C) to the wiper seal (7) prior to assembly.
Installation Procedure
Table 4
Required Tools
Tool Part Number Part Description Qty
A 4C-9485 Pin Driver Cap 1
8/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 15 g01218011
1. Attach a suitable lifting device to boom cylinder (11), as shown. The weight of boom cylinder
(11) is approximately 287 kg (632 lb). Position boom cylinder (11) onto the machine.
Illustration 16 g01218013
2. Install shims (17) and pin assembly (19) on the head end of boom cylinder (11). Install bolt
(18).
Illustration 17 g01217921
3. Use the suitable lifting device to position boom cylinder (11) onto suitable cribbing. Reposition
the suitable lifting device near the rod end of boom cylinder (11). The weight of boom cylinder
(11) is approximately 287 kg (632 lb). Use the suitable lifting device to raise the rod end of
boom cylinder (11) into position.
9/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 18 g01218505
Illustration 19 g01217928
4. Install shim (16). Position pin (15) through the rod end of the boom cylinder.
5. Install spacer (14) (not shown). Install plate (13) and bolts (12).
Illustration 20 g01217915
6. Position valve assembly (10) and install bolts (9).
10/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 21 g01217912
7. Position tube assembly (8) and install bolts (7).
Illustration 22 g01217908
8. Install support assemblies (5) and bolts (6).
Illustration 23 g01217906
9. Install clamps (4).
11/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 24 g01217850
10. Install bolts (3).
Illustration 25 g01217839
Illustration 26 g01217840
11. Turn bolt (2) clockwise into the original position. Tighten nut (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 25 17:19:09 UTC+0800 2020
12/12(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR DHK
Configuration: 320D & 320D L Excavators DHK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320D Excavator Machine Systems
Media Number -RENR8614-14 Publication Date -01/05/2013 Date Updated -19/07/2017
i02462986
Boom - Remove
SMCS - 6501-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9485 Pin Driver Cap 1
B 1U-9202 Lever Puller Hoist 1
C
3S-6224 Electric Hydraulic Pump Gp 1
141-1785 Receiving Sleeve 1
9U-6811 Puller Stud 1
9U-6809 Nut 1
6V-0113 Double Acting Cylinder 1
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
B. Remove the stick. Refer to Disassembly and Assembly, "Stick - Remove".
1/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g01212856
1. Disconnect grease hose assembly (1) from boom cylinder (3). Remove bolts (2). Remove
the retainer plate and spacer (4).
Illustration 2 g01212871
Illustration 3 g01212838
2/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 2. Attach a suitable lifting device to boom cylinder (3). The weight of boom cylinder (3) is
approximately 287 kg (633 lb). Install Tooling (A) into pin (5). Use a hammer to drive pin
(5) out of boom cylinder (3). Lower boom cylinder (3) .
Note: Remove any shims that may be present. Mark the shims for installation purposes.
3. Repeat Steps 1 through 2 for the other boom cylinder.
Illustration 4 g01212891
4. Remove bolts (6). Remove cover (7) .
Illustration 5 g01212899
5. Remove three bolts (8). Remove step (9) .
3/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 6 g01212931
Illustration 7 g01212925
6. Open cover (10) of the storage box. Remove bolts (13). Remove bolts (12) and remove
handhold (11) .
4/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 8 g01228933
7. Position retainer plate (4) and bolts (2) onto each side of pin (5). Attach a suitable lifting
device to each side of pin (5) .
Illustration 9 g01217554
Illustration 10 g01212951
8. Attach a suitable lifting device to pin assembly (15). The weight of pin assembly (15) is
approximately 48 kg (105 lb). Install pin assembly (15) and install bolt (16) .
9. Attach Tooling (B) and a suitable lifting device to boom (14) and pin assembly (15). The
combined weight of boom (14) and the stick cylinder is between 1500 kg (3300 lb) and
3016 kg (6650 lb). Apply slight lifting tension to boom (14) .
5/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 14 g01212983
12. Remove bolt (24). Attach a suitable lifting device to Tooling (C). The weight of Tooling (C)
is approximately 136 kg (300 lb). Attach Tooling (C) to pin assembly (23). Use Tooling (C)
in order to remove pin assembly (23). The combined weight of Tooling (C) and pin
assembly (23) is approximately 215 kg (475 lb).
13. Remove the boom. Remove any shims that may be present.
Note: Note the locations of any shims for assembly purposes.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 25 17:20:04 UTC+0800 2020
7/7(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR DHK
Configuration: 320D & 320D L Excavators DHK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320D Excavator Machine Systems
Media Number -RENR8614-14 Publication Date -01/05/2013 Date Updated -19/07/2017
i07137701
Boom Bearings and Seals - Remove and Install
SMCS - 6501-010-SA; 6501-010-BD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
350-7768 Electric Hydraulic Pump Gp (115V) -1
350-7769 Electric Hydraulic Pump Gp(230V) -
4C-9634 Puller Stud 1
9U-6832 Nut 1
5P-8712 Bushing 1
316-1489 Double Acting Cylinder 1
134-8469 Spacer 1
9U-5338 Bearing Puller Adapter 1
Start By:
a. Remove the boom. Refer to Disassembly and Assembly, "Boom - Remove".
1/4(W)
w
2020/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...