This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...nai93qing
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...nai93qing
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fusjekkdmdmd2w
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to keep parts clean and contain fluids properly during the repair work.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...zoat27912076
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8skjdkdmdmd
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fhjsekdmdm3e
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...8dusjkdmmdmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fujsekkdmmdm
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for disassembling a pilot valve used in 322C and 322C L excavators. The summary is as follows:
1. The pilot valve is first removed from the machine according to separate instructions. It is then disassembled by removing fittings, seals, pedals, covers, springs, balls, bushings, and spools.
2. Specific components removed include O-rings, caps, packings, springs, spring seats, and retaining rings.
3. The spool assemblies are further disassembled by removing seats, springs, washers, and spools. Identification marks are placed on components and cleanliness is important during disassembly.
This document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. The disassembly procedure involves removing 20 different parts from the pilot valve in a specific order. The assembly procedure instructs assembling the pilot valve in the reverse order and notes that cleanliness is important. The document is a service manual providing detailed steps to take the pilot valve apart and rebuild it.
More Related Content
Similar to Caterpillar Cat 320C LN Excavator (Prefix DBG) Service Repair Manual (DBG00001 and up).pdf
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Proper cleaning and installation of seals is also addressed.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fusjekkdmdmd2w
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to keep parts clean and contain fluids properly during the repair work.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...zoat27912076
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8skjdkdmdmd
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fhjsekdmdm3e
This document provides instructions for removing and installing a crankshaft pulley on Caterpillar 320C excavator models. The removal procedure involves using a combination puller tool to remove the nut and washer from the crankshaft, then using a puller tool to remove the pulley. The installation procedure specifies cleaning the crankshaft, placing the pulley in position, and securing it with a washer and nut tightened to the specified torque. Tools required include a combination puller, socket, and cleaning supplies.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...8dusjkdmmdmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...fujsekkdmmdm
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Similar to Caterpillar Cat 320C LN Excavator (Prefix DBG) Service Repair Manual (DBG00001 and up).pdf (20)
This document provides instructions for disassembling a pilot valve used in 322C and 322C L excavators. The summary is as follows:
1. The pilot valve is first removed from the machine according to separate instructions. It is then disassembled by removing fittings, seals, pedals, covers, springs, balls, bushings, and spools.
2. Specific components removed include O-rings, caps, packings, springs, spring seats, and retaining rings.
3. The spool assemblies are further disassembled by removing seats, springs, washers, and spools. Identification marks are placed on components and cleanliness is important during disassembly.
This document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. The disassembly procedure involves removing 20 different parts from the pilot valve in a specific order. The assembly procedure instructs assembling the pilot valve in the reverse order and notes that cleanliness is important. The document is a service manual providing detailed steps to take the pilot valve apart and rebuild it.
This document provides instructions for disassembling the governor of an excavator engine. It lists the required tools and parts that need to be removed in sequential order. These include removing covers, springs, flyweights, shafts, seals and other internal components. Instructions are provided to properly release spring forces and inspect parts for wear or damage. Replacement parts are noted where needed.
1. The document provides instructions for removing the fuel injection pump from a Caterpillar 321D LCR excavator. It lists the required tools and safety notices, including waiting for fuel pressure to purge before servicing fuel lines.
2. The procedure involves first removing the fan drive, then disconnecting fuel lines and harness assemblies. Identification marks should be placed on disconnected parts.
3. Bolts are removed to access the fuel injection pump, fuel manifold, and other internal fuel system components. Cleanliness is important to prevent contaminants from entering the system.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, disconnect electrical and fuel connections, remove mounting hardware, and discard single-use items like lines.
3. Installation is the reverse, using new single-use items and tightening connections to the specified torques while maintaining cleanliness.
- The document provides instructions for removing and installing an electronic unit injector from a Caterpillar C6.4 engine.
- It describes removing components like the valve mechanism cover and fuel lines first. Then using tools like a pry bar and fuel system protection kit, the injector can be removed by loosening nuts, disconnecting harnesses, and removing bolts.
- Reinstallation involves installing new seals and washers, then reversing the removal steps like tightening nuts and reconnecting harnesses.
The document provides instructions for removing and installing a fuel injection pump gear on a Caterpillar C6.4 engine. It outlines 19 steps for removing the gear, including using a puller tool and removing a key. It then describes 2 steps for installing the gear, which are to install the key and tighten a nut while holding the gear in a vice.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 321C EXCAVATOR. The removal procedure involves taking out the threaded plug, shim, spring and spring seat from the right side of the cylinder block. The installation procedure specifies cleaning all parts and reversing the removal steps. Technicians are advised to inspect parts for wear and replace as needed.
This document provides instructions for installing and removing several components of a Caterpillar 320 excavator engine, including:
- Installing and removing the turbocharger, following cleaning and inspection of gaskets.
- Removing and installing the exhaust manifold, ensuring clean gaskets are used.
- Removing and installing the air inlet heater assembly after checking gasket conditions.
- Procedures for removing the inlet manifold after other component removals, checking gaskets for wear.
- Instructions for installing the inlet manifold, ensuring clean gaskets are used.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320E excavator. The removal procedure involves using guide studs and lifting tools to support the flywheel, then removing mounting bolts. The flywheel and ring gear are inspected for wear. To install, the components are positioned with guide studs and lifting tools, then mounting bolts are tightened to the specified torque.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320E excavator. The removal procedure involves using guide studs and lifting tools to support the flywheel, then removing mounting bolts. The flywheel and ring gear are inspected for wear. To install, the procedure is reversed - the flywheel is positioned using guide studs and lifting tools, then mounting bolts are tightened to the specified torque.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to remove the valve keepers and springs with the piston at top dead center. Instructions are provided for inspecting and cleaning components, installing new valve stem seals if needed, and reassembling the valves and springs in the proper order. Torque specifications are included for reinstalling components.
Caterpillar Cat 320E L Excavator (Prefix NAZ) Service Repair Manual (NAZ00001...xiapokang564341
This document provides the procedure for removing and installing inlet and exhaust valve springs on Caterpillar C6.6 engines. The procedure involves using specialized tools to compress the valve springs, rotate the crankshaft to position the piston at top dead center, and remove/install the valve spring and associated components. Proper compression of the valve springs is important to avoid damage and ensure personal safety due to the force of the springs. Cleanliness of parts is also emphasized to prevent premature wear.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to remove the valve keepers and springs with the piston at top dead center. Instructions are provided for inspecting and cleaning components, installing new valve stem seals if needed, and reassembling the valves and springs in the proper order. Torque specifications are included for reinstalling components.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...xiapokang564341
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
Caterpillar Cat 320D L Excavator (Prefix MGG) Service Repair Manual (MGG00001...xiapokang564341
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...xiapokang564341
The document provides instructions for removing and installing the flywheel housing on a Caterpillar 320D excavator. Key steps include:
1. Using lifting equipment, remove the flywheel housing bolts and remove the housing.
2. Use tools to remove the oil seal from the housing.
3. Clean the mating surfaces, install a new gasket on the cylinder block, and re-install the housing using new bolts.
- The document provides instructions to remove and install a crankshaft pulley on a Caterpillar C6.4 engine.
- To remove the pulley, use a combination puller tool to pull the pulley off the crankshaft. Clean any contaminants from the pulley and crankshaft mating surfaces.
- To install the pulley, apply a retaining compound to the crankshaft and pulley mating surfaces. Use a 46mm socket and installer tool to press the pulley onto the crankshaft. Reinstall the belt once the pulley is installed.
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator including:
- Removing the flywheel using link brackets and forcing bolts.
- Removing the crankshaft rear seal using a slide hammer puller and seal distorter.
- Installing a new crankshaft rear seal with a wear sleeve using an installer, locator, bolts and washer.
- Removing the flywheel housing using link brackets and lifting it off with bolts and washers.
- Installing a new oil seal and bolting the flywheel housing back on with new gaskets.
- Removing the crankshaft pulley using a combination puller
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:20:55 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:22:47 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:23:43 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:24:39 UTC+0800 2019
4/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:25:34 UTC+0800 2019
2/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:26:30 UTC+0800 2019
2/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...