This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...fjskekmmem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...ufjkskemsem
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...fjskekmmem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...ufjjsjekkeemme
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...ufjjsjekkeemme
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...fjskekmmem
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...fjskekmmem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...ufjkskemsem
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...fjskekmmem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...ufjjsjekkeemme
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...ufjjsjekkeemme
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...fjskekmmem
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
CASE IH MAXXUM 130 Multicontroller EP Europe F4DFE413AA Service Repair Manual...8dusjkdmmdmd
This document is a service manual that provides instructions for servicing and repairing components of MAXXUM tractors. It includes sections covering the engine, transmission, axles, brakes, hydraulics and other systems. The document provides detailed procedures, specifications, diagrams and troubleshooting information to guide technicians in servicing and repairing issues with the tractors.
CASE IH MAXXUM 125 Multicontroller EP Europe F4DFE613EA Service Repair Manual...8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 125 EP Europe F4DFE613EA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual that provides instructions for servicing and repairing components of MAXXUM tractors. It includes sections covering the engine, transmission, axles, brakes, hydraulics and other systems. The document provides detailed procedures, specifications, diagrams and troubleshooting information to guide technicians in servicing and repairing issues with the tractors.
CASE IH MAXXUM 120 EP Europe F4DFE413DA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual that provides instructions for servicing and repairing components of MAXXUM tractors. It includes sections covering the engine, transmission, axles, brakes, hydraulics and other systems. The document provides detailed procedures, specifications, diagrams and troubleshooting information to guide technicians in servicing and repairing issues with the tractors.
CASE IH MAXXUM 115 Multicontroller EP Europe F4DFE613FA Service Repair Manual...8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 115 EP Europe F4DFE613FA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains information on engine systems, transmission, four-wheel drive systems, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each major system is broken down into specific components and subsystems.
CASE IH MAXXUM 110 EP Europe F4DFE413EA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 110 Multicontroller EP Europe F4DFE413CA Service Repair Manual...8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains information on engine systems, transmission, four-wheel drive systems, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each major system section includes subsections covering specific components and repairs.
CASE IH Magnum 340 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
The document provides instructions to remove an engine from a tractor. It involves disconnecting various engine components like hoses, wiring harnesses, fuel lines and other connections. The engine removal requires draining fluids, removing shields, disconnecting batteries and disengaging over 20 connection points before the engine can be lifted out. Proper precautions like capping fittings and plugging lines are mentioned.
CASE IH Magnum 290 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
This document is a service manual for Magnum tractors 235, 260, 290, 315, and 340. It contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, pneumatic systems, hitches and couplings, steering, cab climate control, electrical systems, and the platform, cab, bodywork, and decals. Safety information is provided at the beginning regarding safety symbols and precautions to take when operating or servicing the equipment.
CASE IH Magnum 260 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
The document provides instructions to remove an engine from a tractor. It involves disconnecting various engine components like hoses, wiring harnesses, fuel lines and other connections. The engine removal requires draining fluids, removing shields, disconnecting batteries and disengaging over 20 connection points before the engine can be lifted out. Proper precautions like capping fittings and plugging lines are mentioned.
CASE IH Magnum 235 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
This document is a service manual for Magnum tractors models 235, 260, 290, 315, and 340. It contains information on engine systems, transmission, four-wheel drive systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, pneumatic systems, hitches and couplings, steering systems, cab climate control, and electrical systems. Safety precautions and symbols are defined at the beginning.
CASE IH LB434 XL Square Baler Service Repair Manual (PIN 4151 and above).pdf8dusjkdmmdmd
This service manual section provides information on the power take-off (PTO) system for a baler. It includes exploded views and detailed views of the PTO drive shaft components. Troubleshooting tips are provided for common PTO issues like wear on yoke ears or separation of telescoping tubes. Instructions are given for disassembling the guards on the inner side of the PTO drive shaft. Technical specifications, diagrams, and procedures for servicing the PTO system are covered in detail in 3 sentences or less.
CASE IH AXIAL-FLOW 9120 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains over 55 sections covering the various systems of the combine, including the engine, transmission, axles, hydraulics, electrical, and more. Each section provides information on components and maintenance for that system. The manual is intended to assist technicians in servicing and repairing the combines.
CASE IH AXIAL-FLOW 9230 Tier 4 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains sections covering the engine, transmission, axles, steering, brakes, hydraulic and electrical systems, cab controls, and attachments/headers for the combines. The manual provides specifications and repair/maintenance procedures for various components of the combines. It is copyrighted and printed in the USA by CNH America LLC for Case IH combines.
CASE IH AXIAL-FLOW 8230 Tier 4 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains sections covering the engine, transmission, axles, steering, brakes, hydraulic and electrical systems, cab controls, and attachments/headers for the combines. The manual provides maintenance and repair information for technicians and is copyrighted and printed in the USA.
CASE IH AXIAL-FLOW 8120 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains over 55 sections covering the various systems of the combine, including the engine, transmission, axles, hydraulics, electrical, and more. Each section provides information on components and maintenance for that system. The manual is intended to assist technicians in servicing and repairing the combines.
CASE IH AXIAL-FLOW 7230 Tier 4 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is the service manual for Case IH Axial-Flow combines. It contains instructions for servicing and repairing components of the combines such as the engine, transmission, hydraulics, electrical systems, attachments, and other systems. The manual provides an introduction and table of contents that outline the organization and contents of the manual. It also includes safety information and instructions that should be followed when servicing the machines.
CASE IH AXIAL-FLOW 7120 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH Axial-Flow combines models 7120, 8120, and 9120. It contains over 200 sections covering all aspects of the combines from the engine and drivetrain to the electrical systems and attachments. Each section provides detailed information and specifications for servicing and repairing components. Safety precautions are provided at the beginning regarding personal safety when working on the equipment.
CASE IH PUMA 155 Multicontroller Tractor Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual that contains information about the hydraulic, pneumatic, electrical, and electronic systems for PUMA excavators. It includes sections covering the primary hydraulic power system, secondary hydraulic power system, pneumatic system, electrical power system, electronic system, engine systems, transmission and drive systems, axles, brakes and steering systems, the frame and cab, hitches and working tools. The manual is divided into sections and chapters to organize information by system, and each chapter contains technical data, descriptions of functionality, diagnostic information, and service procedures.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
CASE IH MAXXUM 130 Multicontroller EP Europe F4DFE413AA Service Repair Manual...8dusjkdmmdmd
This document is a service manual that provides instructions for servicing and repairing components of MAXXUM tractors. It includes sections covering the engine, transmission, axles, brakes, hydraulics and other systems. The document provides detailed procedures, specifications, diagrams and troubleshooting information to guide technicians in servicing and repairing issues with the tractors.
CASE IH MAXXUM 125 Multicontroller EP Europe F4DFE613EA Service Repair Manual...8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 125 EP Europe F4DFE613EA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual that provides instructions for servicing and repairing components of MAXXUM tractors. It includes sections covering the engine, transmission, axles, brakes, hydraulics and other systems. The document provides detailed procedures, specifications, diagrams and troubleshooting information to guide technicians in servicing and repairing issues with the tractors.
CASE IH MAXXUM 120 EP Europe F4DFE413DA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual that provides instructions for servicing and repairing components of MAXXUM tractors. It includes sections covering the engine, transmission, axles, brakes, hydraulics and other systems. The document provides detailed procedures, specifications, diagrams and troubleshooting information to guide technicians in servicing and repairing issues with the tractors.
CASE IH MAXXUM 115 Multicontroller EP Europe F4DFE613FA Service Repair Manual...8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 115 EP Europe F4DFE613FA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains information on engine systems, transmission, four-wheel drive systems, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each major system is broken down into specific components and subsystems.
CASE IH MAXXUM 110 EP Europe F4DFE413EA Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 110 Multicontroller EP Europe F4DFE413CA Service Repair Manual...8dusjkdmmdmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains information on engine systems, transmission, four-wheel drive systems, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each major system section includes subsections covering specific components and repairs.
CASE IH Magnum 340 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
The document provides instructions to remove an engine from a tractor. It involves disconnecting various engine components like hoses, wiring harnesses, fuel lines and other connections. The engine removal requires draining fluids, removing shields, disconnecting batteries and disengaging over 20 connection points before the engine can be lifted out. Proper precautions like capping fittings and plugging lines are mentioned.
CASE IH Magnum 290 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
This document is a service manual for Magnum tractors 235, 260, 290, 315, and 340. It contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, pneumatic systems, hitches and couplings, steering, cab climate control, electrical systems, and the platform, cab, bodywork, and decals. Safety information is provided at the beginning regarding safety symbols and precautions to take when operating or servicing the equipment.
CASE IH Magnum 260 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
The document provides instructions to remove an engine from a tractor. It involves disconnecting various engine components like hoses, wiring harnesses, fuel lines and other connections. The engine removal requires draining fluids, removing shields, disconnecting batteries and disengaging over 20 connection points before the engine can be lifted out. Proper precautions like capping fittings and plugging lines are mentioned.
CASE IH Magnum 235 Tractor Service Repair Manual (PIN ZBRD07000 and after).pdf8dusjkdmmdmd
This document is a service manual for Magnum tractors models 235, 260, 290, 315, and 340. It contains information on engine systems, transmission, four-wheel drive systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, pneumatic systems, hitches and couplings, steering systems, cab climate control, and electrical systems. Safety precautions and symbols are defined at the beginning.
CASE IH LB434 XL Square Baler Service Repair Manual (PIN 4151 and above).pdf8dusjkdmmdmd
This service manual section provides information on the power take-off (PTO) system for a baler. It includes exploded views and detailed views of the PTO drive shaft components. Troubleshooting tips are provided for common PTO issues like wear on yoke ears or separation of telescoping tubes. Instructions are given for disassembling the guards on the inner side of the PTO drive shaft. Technical specifications, diagrams, and procedures for servicing the PTO system are covered in detail in 3 sentences or less.
CASE IH AXIAL-FLOW 9120 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains over 55 sections covering the various systems of the combine, including the engine, transmission, axles, hydraulics, electrical, and more. Each section provides information on components and maintenance for that system. The manual is intended to assist technicians in servicing and repairing the combines.
CASE IH AXIAL-FLOW 9230 Tier 4 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains sections covering the engine, transmission, axles, steering, brakes, hydraulic and electrical systems, cab controls, and attachments/headers for the combines. The manual provides specifications and repair/maintenance procedures for various components of the combines. It is copyrighted and printed in the USA by CNH America LLC for Case IH combines.
CASE IH AXIAL-FLOW 8230 Tier 4 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains sections covering the engine, transmission, axles, steering, brakes, hydraulic and electrical systems, cab controls, and attachments/headers for the combines. The manual provides maintenance and repair information for technicians and is copyrighted and printed in the USA.
CASE IH AXIAL-FLOW 8120 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH axial-flow combines. It contains over 55 sections covering the various systems of the combine, including the engine, transmission, axles, hydraulics, electrical, and more. Each section provides information on components and maintenance for that system. The manual is intended to assist technicians in servicing and repairing the combines.
CASE IH AXIAL-FLOW 7230 Tier 4 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is the service manual for Case IH Axial-Flow combines. It contains instructions for servicing and repairing components of the combines such as the engine, transmission, hydraulics, electrical systems, attachments, and other systems. The manual provides an introduction and table of contents that outline the organization and contents of the manual. It also includes safety information and instructions that should be followed when servicing the machines.
CASE IH AXIAL-FLOW 7120 Combine Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual for Case IH Axial-Flow combines models 7120, 8120, and 9120. It contains over 200 sections covering all aspects of the combines from the engine and drivetrain to the electrical systems and attachments. Each section provides detailed information and specifications for servicing and repairing components. Safety precautions are provided at the beginning regarding personal safety when working on the equipment.
CASE IH PUMA 155 Multicontroller Tractor Service Repair Manual.pdf8dusjkdmmdmd
This document is a service manual that contains information about the hydraulic, pneumatic, electrical, and electronic systems for PUMA excavators. It includes sections covering the primary hydraulic power system, secondary hydraulic power system, pneumatic system, electrical power system, electronic system, engine systems, transmission and drive systems, axles, brakes and steering systems, the frame and cab, hitches and working tools. The manual is divided into sections and chapters to organize information by system, and each chapter contains technical data, descriptions of functionality, diagnostic information, and service procedures.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:20:55 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:22:47 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:23:43 UTC+0800 2019
3/3(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:24:39 UTC+0800 2019
4/4(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:25:34 UTC+0800 2019
2/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 22 12:26:30 UTC+0800 2019
2/2(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR DBG
Configuration: 320C, 320C L, 320C LN Excavators DBG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5(W)
w
2019/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...