Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 9KK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 9KK00001-01358 (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615533
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g00609491
Illustration 2 g00609490
1. Use Tool (A) to install bushing (7) into rocker arm (6), if the bushing was removed.
Refer to Specifications, "Rocker Shaft" for more information.
Illustration 3 g00609488
2. Install spacer (4) and clip (3) onto one end of shaft assembly (5) .
3. Slide components onto shaft (5) in the correct order. Refer to Illustration 1 in order to install
the components correctly.
4. The shaft assembly includes the following components:
◦ Bolt (1)
◦ Oil tube (2)
◦ Clip (3)
2/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. ◦ Spacer (4)
◦ Shaft assembly (5)
◦ Rocker arm (6)
◦ Bushing (7)
◦ Rocker shaft bracket (8)
◦ Spring (9)
5. Install spacer (4) and clip (3) onto the other end of shaft assembly (5) .
6. Install bolt (1) and oil supply tube (2) into the end of shaft assembly (5) .
End By: Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 16:12:07 UTC+0800 2019
3/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 9KK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 9KK00001-01358 (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01576835
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00609287
1. Install valve caps (7) on the end of the valve stem.
2. Install pushrods (5) in the cylinder head assembly (6) .
1/2(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Note: Ensure that the pushrods are installed in the original location. Also, ensure that the
pushrods are seated in the valve lifters correctly.
Illustration 2 g00609267
3. Place the rocker shaft assembly (4) in position on the cylinder head.
4. Install six long bolts (3) for the rocker shaft bracket and tighten the bolts to a torque of 15 ±
3 N·m (11 ± 2 lb ft).
5. Install six short bolts (2) and the washers. Tighten the short bolts to a torque of 15 ± 3 N·m
(11 ± 2 lb ft).
Note: Perform Steps 1 through 5 for the other head assembly on the 3066 Engine.
6. Adjust the inlet valve lash and the exhaust valve lash to 0.25 mm (0.010 inch). Refer to
Testing and Adjusting, "Air Inlet and Exhaust System" for more information on setting the
valve lash. Tighten adjusting screws (1) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 16:13:03 UTC+0800 2019
2/2(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 9KK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 9KK00001-01358 (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02088121
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
A. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
B. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Remove".
C. Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
D. Remove the water temperature regulator. Refer to Disassembly and Assembly, "Water
Temperature Regulator- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/5(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: The 3064 Engine has one cylinder head, while the 3066 Engine has two cylinder heads.
Illustration 1 g00527527
Torque sequence for the cylinder head bolts ( 3066 Engine)
2/5(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 2 g00527556
Torque sequence for the cylinder head bolts ( 3064 Engine)
Illustration 3 g00604993
1. Gradually remove the cylinder head bolts (1) from the cylinder head. The 3066 Engine has
thirteen cylinder head bolts while the 3064 Engine has seventeen cylinder head bolts.
Remove the bolts in reverse order of the torque sequence.
Note: Do not use a pry bar to separate the cylinder head from the engine block.
3/5(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 4 g00605044
Typical example
2. Install Tooling (A), chains and a suitable lifting device to cylinder head (2) .
3. Remove the cylinder head (2) from the cylinder block. The weight of the cylinder head
assembly for the 3066 Engine is 32 kg (70 lb). The weight of the cylinder head assembly for
the 3064 Engine is 45 kg (100 lb).
Note: Place the cylinder head on a surface that will not damage the face of the cylinder
head.
Illustration 5 g00605078
Note: When the gasket is removed from the cylinder block, be careful not to damage the
mounting face of the cylinder block.
4. Remove the cylinder head gasket (3) from the cylinder block.
5. Repeat Step 1 through Step 4 for the other cylinder head ( 3066 Engine).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 16:13:59 UTC+0800 2019
4/5(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 9KK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 9KK00001-01358 (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02795026
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The 3064 Engine has one cylinder head, while the 3066 Engine has two cylinder heads.
1/4(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00605078
1. Clean the surfaces of the cylinder head and the cylinder block that are in contact with each
other. Ensure that the surfaces are clean and dry. Install a new, dry cylinder head gasket (3)
on the cylinder block.
Note: Do not use any sealant or gasket adhesive on the cylinder head gasket .
Illustration 2 g00605044
Typical example
2. Install Tooling (A) , chains, and a suitable lifting device to the cylinder head.
3. Install the cylinder head in position on the cylinder block. The weight of the cylinder head
assembly for the 3066 Engine is approximately 32 kg (70 lb). The weight of the cylinder
head assembly for the 3064 Engine is approximately 45 kg (100 lb).
4. Remove Tooling (A) .
2/4(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 3 g00604993
5. Put clean engine oil on the threads of the cylinder head bolts. Install thirteen cylinder head
bolts (1) into cylinder head (2) ( 3066 Engine). Install seventeen cylinder head bolts (1) into
cylinder head (2) ( 3064 Engine).
Illustration 4 g00527556
Torque sequence for the cylinder head bolts ( 3064 Engine)
3/4(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 5 g00527527
Torque sequence for the cylinder head bolts ( 3066 Engine)
6. Tighten the cylinder head bolts in the appropriate numerical sequence to torque of118 ± 5
N·m (87 ± 4 lb ft).
7. Repeat step 9 through step 6 for the other cylinder head ( 3066 Engine).
8. After assembly, run the engine to operating temperature.
9. Stop the engine and allow the engine to cool.
10. Tighten the cylinder head bolts again in the appropriate numerical sequence to a torque of
118 ± 5 N·m (87 ± 4 lb ft).
End By:
a. Install the water temperature regulator. Refer to Disassembly and Assembly, "Water
Temperature Regulator - Remove and Install".
b. Install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
c. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Install".
d. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 16:14:54 UTC+0800 2019
4/4(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 9KK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 9KK00001-01358 (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615579
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00610824
1/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 2 g00532061
1. Use a magnet to remove valve lifter (1) from the engine cylinder block, as shown. Put
identification marks on the valve lifters for installation purposes.
2. Repeat Step 1 for the remainder of the valve lifters.
Illustration 3 g00613675
View (X) shows a good contact pattern. Views (Y) and (Z) show bad contact patterns.
Note: Check the valve lifters for wear.
Note: Refer to Specifications, "Camshaft" for more information on valve lifters.
Installation Procedure
2/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00532061
1. Put 8T-2998 Lubricant on valve lifter (1) prior to installation. Install valve lifter (1) in the
original location in the engine cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 16:15:50 UTC+0800 2019
3/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 L EXCAVATOR 9KK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 9KK00001-01358 (MACHINE) POWERED BY 3066 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01568538
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Remove".
B. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
C. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
Note: In this removal procedure, the engine needs to be placed in the upside-down position. This
will allow the lifters to remain in position after the camshaft is removed.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00569371
Note: Ensure that the marks on the timing gears are in alignment. Align fuel injection drive gear
(A) with the "33" mark with the "3" mark on idler gear (B). Make an alignment of the "2" mark on
camshaft gear (C) with the "22" mark on idler gear (B). Align the "1" mark on crankshaft gear (D)
with the "11" mark on idler gear (B). The No. 1 cylinder is at the top center position when these
marks are in alignment.
1. Rotate the engine at 180 degrees in order to place the engine in the upside-down position.
This will ease the removal of the camshaft.
2/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Illustration 2 g00604521
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Remove
two bolts (1) and the washers that hold thrust plate (3) (not shown).
3. Carefully remove the camshaft, the thrust plate and the camshaft gear as an assembly.
4. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 16:16:46 UTC+0800 2019
3/3(W)w
2019/12/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
