The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using specialized tools to compress the valve springs, remove the keepers and other parts, and then reverse the process for installation. Safety precautions are outlined to prevent injury from the force of compressed springs. A second section provides similar instructions for removing and installing the engine oil filter base.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fhhjsjekmdme
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using a valve spring compressor tool to compress the valve springs, allowing removal of the valve keepers and springs. Identification marks should be made on the valves and springs. Removal and installation is reversed, with inspection of components and lubrication of valve stems before reinstallation. Safety precautions are noted regarding the force of compressed springs. A similar process is described for removing and installing the engine oil filter base.
Caterpillar cat 320 e excavator (prefix aws) service repair manual (aws00001 ...fhhjsjekmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E excavator engine. The summary is:
1. The procedure describes removing the cylinder head and using a valve spring compressor tool to compress the valves springs, remove the keepers, and take out the valves.
2. Reinstallation involves cleaning components, lubricating the valve stems, and using the compressor tool to insert the valves back into the cylinder head and replace the springs and keepers.
3. Proper torque values are provided for reinstalling the cylinder head.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D2 L excavator engine. It describes using a valve spring compressor tool to compress the valve springs before removing the valve keepers and other components. When installing new valves, the instructions specify cleaning and lubricating components, compressing springs with the tool to install keepers, and checking valve depths once installation is complete. Removal and installation of valve guides requires special machinery and trained personnel and includes reaming guides and cutting valve seats after installation.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fjskemedcdmme
The document provides instructions to remove and install inlet and exhaust valves on a Caterpillar 320E excavator engine. It describes:
1) Using specialized tools to compress the valve springs and remove the keepers and other valve components.
2) Inspecting and cleaning the valve components before installation.
3) Lubricating the valves and installing them in the proper orientation, then using tools to compress the springs and install new keepers.
4) Installing a new cylinder head gasket and bolting on the cylinder head once the valves are reassembled.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fhhjsjekmdme
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using a valve spring compressor tool to compress the valve springs, allowing removal of the valve keepers and springs. Identification marks should be made on the valves and springs. Removal and installation is reversed, with inspection of components and lubrication of valve stems before reinstallation. Safety precautions are noted regarding the force of compressed springs. A similar process is described for removing and installing the engine oil filter base.
Caterpillar cat 320 e excavator (prefix aws) service repair manual (aws00001 ...fhhjsjekmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E excavator engine. The summary is:
1. The procedure describes removing the cylinder head and using a valve spring compressor tool to compress the valves springs, remove the keepers, and take out the valves.
2. Reinstallation involves cleaning components, lubricating the valve stems, and using the compressor tool to insert the valves back into the cylinder head and replace the springs and keepers.
3. Proper torque values are provided for reinstalling the cylinder head.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D2 L excavator engine. It describes using a valve spring compressor tool to compress the valve springs before removing the valve keepers and other components. When installing new valves, the instructions specify cleaning and lubricating components, compressing springs with the tool to install keepers, and checking valve depths once installation is complete. Removal and installation of valve guides requires special machinery and trained personnel and includes reaming guides and cutting valve seats after installation.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding the force of compressed springs. A separate section then details removing and installing the engine oil filter base.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fjskemedcdmme
The document provides instructions to remove and install inlet and exhaust valves on a Caterpillar 320E excavator engine. It describes:
1) Using specialized tools to compress the valve springs and remove the keepers and other valve components.
2) Inspecting and cleaning the valve components before installation.
3) Lubricating the valves and installing them in the proper orientation, then using tools to compress the springs and install new keepers.
4) Installing a new cylinder head gasket and bolting on the cylinder head once the valves are reassembled.
New holland tj325 tractor service repair manualufjkskemsem
- This document contains safety information and warnings for operating machinery.
- Operators should read the entire manual and all safety signs on the machine before operating.
- When servicing machinery, always turn off the engine, set the parking brake, remove the key and block the wheels before working on the machine.
- Wear proper safety equipment like a hard hat, safety shoes, gloves, eye protection and reflective clothing when operating machinery.
Massey ferguson mf 363 lx tractor service parts catalogue manual (part number...ufjkskemsem
This document contains parts listings and descriptions for the engine of a Massey Ferguson 363 LX tractor. It includes 6 pages detailing over 80 individual engine parts grouped into assemblies like the cylinder block, crankshaft, pistons, cylinder head, and others. Each part lists properties like part number, quantity, description, and additional comments clarifying usage or replacement parts. The level of technical detail provided is aimed at mechanics and part suppliers for maintenance and repair of this tractor engine model.
Massey ferguson mf 353 lx tractor service parts catalogue manual (part number...ufjkskemsem
The document provides parts lists and technical specifications for repairing and replacing components of a Massey Ferguson 353 LX tractor engine. It includes lists of parts needed for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and other engine systems. Each part is accompanied by details like part numbers, quantities, replacement parts, and technical specifications.
Massey ferguson mf 350 tractor service parts catalogue manual (part number 8...ufjkskemsem
This document provides parts information for a Massey Ferguson 350 tractor engine. It includes 4 pages of documentation with diagrams and lists of parts, part numbers, quantities and descriptions for the engine block, cylinder head, crankshaft, pistons, connecting rods and other engine components. Over 100 individual parts are detailed across the 4 pages of documentation.
The document is a parts catalog for a Massey Ferguson 6711 tractor. It contains 24 pages of detailed parts listings for various systems of the tractor, including the engine, axles, steering, brakes, hydraulics, electrical, cab, chassis, and implements. Each page lists the relevant part numbers, quantities, descriptions, and any additional comments for a specific subsystem. The parts are organized in item number order for each section.
Massey ferguson 6499 tractor (tier 3) ( -- t197077) service parts catalogue m...ufjkskemsem
This document provides parts information for a Massey Ferguson 6499 Tier 3 tractor with the serial number 3906159, including:
1. Details on the engine, alternator, starter, cylinder block, timing gear housing, crankshaft, pistons, and connecting rods.
2. Lists 27 items related to the cylinder block, 22 items for the timing gear housing, and 20 items for the crankshaft, pistons, and connecting rods along with part numbers and quantities.
3. Includes notes on part numbers, quantities, and specifications for many of the listed parts.
Massey ferguson 6140 tractor service parts catalogue manual (part number 163...ufjkskemsem
This document provides parts information for the engine of a Massey Ferguson 6140 tractor with serial number 1637275. It includes 42 line items with part numbers, quantities, descriptions and other details for the engine block, cylinder head, crankshaft, pistons, connecting rods and other engine components. It also includes references to other documents for additional part information.
Massey ferguson 6120 tractor service parts catalogue manual (part number 163...ufjkskemsem
This document provides parts information for the engine of a Massey Ferguson 6120 tractor with serial number 1637273. It includes:
1. A list of 32 parts for the engine and their descriptions.
2. A list of 28 parts for the cylinder block and their descriptions.
3. A list of 23 parts for the crankshaft, pistons, and connecting rods and their descriptions.
Massey ferguson 5613 tractor (dyna 6) (e023046 g307020) service parts catal...ufjkskemsem
This document provides a table of contents and parts list for a Massey Ferguson 5613 tractor. The table of contents lists 24 sections that provide information on various tractor systems and components. The parts list documents 33 individual parts that make up the engine assemblies for the tractor, including descriptions and part numbers.
Massey ferguson 5612 tractor (dyna 6) (d295023 g165048) service parts catal...ufjkskemsem
The document is a table of contents for the service manual of a Massey Ferguson 5612 tractor. It lists 24 sections that make up the manual, including the engine, axles, steering system, drive train, brakes, hydraulics, electrical system, cab, chassis, decals, wheels, and implements. Each section includes multiple sub-pages providing part numbers, descriptions and other technical details for servicing and repairing components of the tractor.
John deere power tech e 3.0l diesel engines service repair technical manual (...ufjkskemsem
The document provides instructions for removing and installing various components of PowerTech E 2.4L and 3.0L diesel engines, including the flywheel, flywheel ring gear, flywheel housing, balancer shafts, and measuring main bearing cap clearances. The removal instructions list necessary special tools and safety precautions for each component. Installation sections specify torque specifications and use of thread locking compounds.
1. The document provides instructions for disassembling and reassembling the carrier roller of an excavator model EL240.
2. The disassembly instructions describe cleaning parts and removing components like seals, bolts, and bushings. The reassembly instructions describe installing components in reverse order and applying lubricants like engine oil and threadlock.
3. Maintenance standards are provided for wear limits, repair welding procedures, and storage of items for up to 12 months.
1. The document provides instructions for disassembling and reassembling the carrier roller of an excavator model EL240.
2. The disassembly instructions describe cleaning parts and removing components like seals, bolts, and bushings. The reassembly instructions describe installing components in reverse order and applying lubricants like engine oil.
3. Maintenance standards are provided for wear limits, repair welding procedures, and storage of items for up to 12 months.
Caterpillar cat d8 t track type tractor dozer bulldozer (prefix mb8) service ...ufjkskemsem
This document provides instructions for removing and installing the final drive on a D8T track-type tractor. The removal procedure involves using lifting devices and tools to detach various components of the final drive including the planetary carrier, sprocket hub, and reaction hub. These components are then disassembled further by removing shafts, gears, seals, and bearings. The assembly procedure reverses these steps, noting to clean and lubricate parts, carefully install seals using specialty tools, and tighten fasteners to the specified torques.
Caterpillar cat d8 t track type tractor dozer bulldozer (prefix fct) service ...ufjkskemsem
The document provides instructions for removing and installing various components of a Caterpillar D8T track-type tractor engine. It describes removing the front cover by removing tube assemblies, button head screws, nuts and spacers. It then explains installing the front cover by reversing the removal steps and applying thread lock to the studs. It also describes removing the gear group on the front of the engine by using a driver group after removing the front housing, air compressor and water pump. Workers are warned not to turn the crankshaft or camshaft while the camshaft gear is removed to prevent interference.
Caterpillar cat 320 f l excavator (prefix nhd) service repair manual (nhd0000...ufjkskemsem
This document provides instructions for disassembling and assembling the travel motor of a 320F L excavator. The disassembly procedure involves 27 steps to remove components such as the head, fittings, brake piston, barrel assembly, and shaft. The assembly procedure describes 30 steps including installing seals, plates, springs, and reassembling components in reverse order using alignment marks and applying lubricants. Precautions are outlined to avoid damage and ensure correct assembly of parts like the cam plate.
Caterpillar cat 320 e l excavator (prefix wbk) service repair manual (wbk0000...ufjkskemsem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.6 engine. It describes two procedures: one for a standard housing and one for a wet back-end housing. The standard procedure involves removing bolts to detach the housing from the cylinder block. Dowels and seals must also be inspected or installed. The wet back-end procedure is similar but notes that a seal is not used with this housing on a standard engine. Precise torques are specified for bolts depending on their grade. Alignment of the housing must be checked after installation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...ufjkskemsem
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
New holland tj325 tractor service repair manualufjkskemsem
- This document contains safety information and warnings for operating machinery.
- Operators should read the entire manual and all safety signs on the machine before operating.
- When servicing machinery, always turn off the engine, set the parking brake, remove the key and block the wheels before working on the machine.
- Wear proper safety equipment like a hard hat, safety shoes, gloves, eye protection and reflective clothing when operating machinery.
Massey ferguson mf 363 lx tractor service parts catalogue manual (part number...ufjkskemsem
This document contains parts listings and descriptions for the engine of a Massey Ferguson 363 LX tractor. It includes 6 pages detailing over 80 individual engine parts grouped into assemblies like the cylinder block, crankshaft, pistons, cylinder head, and others. Each part lists properties like part number, quantity, description, and additional comments clarifying usage or replacement parts. The level of technical detail provided is aimed at mechanics and part suppliers for maintenance and repair of this tractor engine model.
Massey ferguson mf 353 lx tractor service parts catalogue manual (part number...ufjkskemsem
The document provides parts lists and technical specifications for repairing and replacing components of a Massey Ferguson 353 LX tractor engine. It includes lists of parts needed for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and other engine systems. Each part is accompanied by details like part numbers, quantities, replacement parts, and technical specifications.
Massey ferguson mf 350 tractor service parts catalogue manual (part number 8...ufjkskemsem
This document provides parts information for a Massey Ferguson 350 tractor engine. It includes 4 pages of documentation with diagrams and lists of parts, part numbers, quantities and descriptions for the engine block, cylinder head, crankshaft, pistons, connecting rods and other engine components. Over 100 individual parts are detailed across the 4 pages of documentation.
The document is a parts catalog for a Massey Ferguson 6711 tractor. It contains 24 pages of detailed parts listings for various systems of the tractor, including the engine, axles, steering, brakes, hydraulics, electrical, cab, chassis, and implements. Each page lists the relevant part numbers, quantities, descriptions, and any additional comments for a specific subsystem. The parts are organized in item number order for each section.
Massey ferguson 6499 tractor (tier 3) ( -- t197077) service parts catalogue m...ufjkskemsem
This document provides parts information for a Massey Ferguson 6499 Tier 3 tractor with the serial number 3906159, including:
1. Details on the engine, alternator, starter, cylinder block, timing gear housing, crankshaft, pistons, and connecting rods.
2. Lists 27 items related to the cylinder block, 22 items for the timing gear housing, and 20 items for the crankshaft, pistons, and connecting rods along with part numbers and quantities.
3. Includes notes on part numbers, quantities, and specifications for many of the listed parts.
Massey ferguson 6140 tractor service parts catalogue manual (part number 163...ufjkskemsem
This document provides parts information for the engine of a Massey Ferguson 6140 tractor with serial number 1637275. It includes 42 line items with part numbers, quantities, descriptions and other details for the engine block, cylinder head, crankshaft, pistons, connecting rods and other engine components. It also includes references to other documents for additional part information.
Massey ferguson 6120 tractor service parts catalogue manual (part number 163...ufjkskemsem
This document provides parts information for the engine of a Massey Ferguson 6120 tractor with serial number 1637273. It includes:
1. A list of 32 parts for the engine and their descriptions.
2. A list of 28 parts for the cylinder block and their descriptions.
3. A list of 23 parts for the crankshaft, pistons, and connecting rods and their descriptions.
Massey ferguson 5613 tractor (dyna 6) (e023046 g307020) service parts catal...ufjkskemsem
This document provides a table of contents and parts list for a Massey Ferguson 5613 tractor. The table of contents lists 24 sections that provide information on various tractor systems and components. The parts list documents 33 individual parts that make up the engine assemblies for the tractor, including descriptions and part numbers.
Massey ferguson 5612 tractor (dyna 6) (d295023 g165048) service parts catal...ufjkskemsem
The document is a table of contents for the service manual of a Massey Ferguson 5612 tractor. It lists 24 sections that make up the manual, including the engine, axles, steering system, drive train, brakes, hydraulics, electrical system, cab, chassis, decals, wheels, and implements. Each section includes multiple sub-pages providing part numbers, descriptions and other technical details for servicing and repairing components of the tractor.
John deere power tech e 3.0l diesel engines service repair technical manual (...ufjkskemsem
The document provides instructions for removing and installing various components of PowerTech E 2.4L and 3.0L diesel engines, including the flywheel, flywheel ring gear, flywheel housing, balancer shafts, and measuring main bearing cap clearances. The removal instructions list necessary special tools and safety precautions for each component. Installation sections specify torque specifications and use of thread locking compounds.
1. The document provides instructions for disassembling and reassembling the carrier roller of an excavator model EL240.
2. The disassembly instructions describe cleaning parts and removing components like seals, bolts, and bushings. The reassembly instructions describe installing components in reverse order and applying lubricants like engine oil and threadlock.
3. Maintenance standards are provided for wear limits, repair welding procedures, and storage of items for up to 12 months.
1. The document provides instructions for disassembling and reassembling the carrier roller of an excavator model EL240.
2. The disassembly instructions describe cleaning parts and removing components like seals, bolts, and bushings. The reassembly instructions describe installing components in reverse order and applying lubricants like engine oil.
3. Maintenance standards are provided for wear limits, repair welding procedures, and storage of items for up to 12 months.
Caterpillar cat d8 t track type tractor dozer bulldozer (prefix mb8) service ...ufjkskemsem
This document provides instructions for removing and installing the final drive on a D8T track-type tractor. The removal procedure involves using lifting devices and tools to detach various components of the final drive including the planetary carrier, sprocket hub, and reaction hub. These components are then disassembled further by removing shafts, gears, seals, and bearings. The assembly procedure reverses these steps, noting to clean and lubricate parts, carefully install seals using specialty tools, and tighten fasteners to the specified torques.
Caterpillar cat d8 t track type tractor dozer bulldozer (prefix fct) service ...ufjkskemsem
The document provides instructions for removing and installing various components of a Caterpillar D8T track-type tractor engine. It describes removing the front cover by removing tube assemblies, button head screws, nuts and spacers. It then explains installing the front cover by reversing the removal steps and applying thread lock to the studs. It also describes removing the gear group on the front of the engine by using a driver group after removing the front housing, air compressor and water pump. Workers are warned not to turn the crankshaft or camshaft while the camshaft gear is removed to prevent interference.
Caterpillar cat 320 f l excavator (prefix nhd) service repair manual (nhd0000...ufjkskemsem
This document provides instructions for disassembling and assembling the travel motor of a 320F L excavator. The disassembly procedure involves 27 steps to remove components such as the head, fittings, brake piston, barrel assembly, and shaft. The assembly procedure describes 30 steps including installing seals, plates, springs, and reassembling components in reverse order using alignment marks and applying lubricants. Precautions are outlined to avoid damage and ensure correct assembly of parts like the cam plate.
Caterpillar cat 320 e l excavator (prefix wbk) service repair manual (wbk0000...ufjkskemsem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.6 engine. It describes two procedures: one for a standard housing and one for a wet back-end housing. The standard procedure involves removing bolts to detach the housing from the cylinder block. Dowels and seals must also be inspected or installed. The wet back-end procedure is similar but notes that a seal is not used with this housing on a standard engine. Precise torques are specified for bolts depending on their grade. Alignment of the housing must be checked after installation.
Caterpillar cat 320 c ln excavator (prefix dbg) service repair manual (dbg000...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 320 c l excavator (prefix dbg) service repair manual (dbg0000...ufjkskemsem
This document provides instructions for removing and installing a crankshaft pulley on excavator models 320C, 320C L, and 320C LN. It outlines the required tools and steps to remove the V-belts, nut, washer, and pulley using a combination puller. It also describes cleaning parts and installing a new pulley by reversing the removal steps. Proper torque is required for reinstallation.
Caterpillar cat 320 c excavator (prefix dbg) service repair manual (dbg00001 ...ufjkskemsem
This document provides instructions for servicing components of Caterpillar 320C excavator engines, including removing and installing the crankshaft front seal, flywheel, and flywheel housing. The procedures describe using various tools to remove parts like the crankshaft seal and installing replacement parts while taking precautions to contain fluids and prevent contamination.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR TNJ
Configuration: 320E L Excavators TNJ00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
C6.6 Engines for Caterpillar Built Machines
Media Number -KENR9249-07 Publication Date -01/09/2015 Date Updated -19/06/2017
i03911450
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove"
for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below
the face of the cylinder head before the valve springs are removed. Refer to Specifications,
"Cylinder Head Valves" for the correct dimensions.
1/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Note: Inlet valves have a recess in the center of the head.
3. Use a suitable lifting device to position the cylinder head with the valve springs upward.
The weight of the cylinder head is approximately 65 kg (143 lb).
Note: Ensure that the cylinder head is kept on a clean, soft surface in order to prevent
damage to the machined face.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 1 g01978994
2/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. 4. Install Tooling (A) into position on the cylinder head in order to compress appropriate valve
spring (3).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (A) in order to remove valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
6. Slowly release the pressure on Tooling (A).
Illustration 2 g01978995
7. Place a temporary identification mark on valve spring (3) in order to identify the correct
position.
8. Remove valve spring retainer (2). Remove valve spring (3).
9. Repeat Step 4 through Step 8 for the remaining valves.
3/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. 10. Remove Tooling (A).
11. Remove valve stem seals (4).
12. Use a suitable lifting device to turn over the cylinder head.
13. Place a temporary identification mark on valves (5). Remove valves (5) from the cylinder
head.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The valves have a hard surface finish. Grinding compound must not be used on the valves.
Grinding compound will damage the hard surface finish of the valves.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and, all lubrication passages in the cylinder head are free from debris. Follow Step
1.a through Step 1.e in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to System Operation,
Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure.
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and System Operation, Testing and Adjusting, "Valve Guide - Inspect"
for further information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves" for the correct information.
4/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. e. Inspect the valve springs for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves " for the correct information.
Illustration 3 g01978995
2. Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate
positions in the cylinder head. Check the depth of the valves below the face of the cylinder
head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more
information.
3. Use a suitable lifting device to turn over the cylinder head. The weight of the cylinder head
is approximately 65 kg (143 lb).
Note: Ensure that all of the valves remain in place.
4. Install new valve stem seals (4) onto each of the valve guides.
Note: The outer face of the valve guides must be clean and dry before installing valve stem
seals (4).
5. Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) on valve
spring (3).
5/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 4 g01978994
6. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (3).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
7. Apply sufficient pressure to Tooling (A) in order to install valve keepers (1).
6/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
8. Carefully release the pressure on Tooling (A).
9. Repeat Step 5 through Step 8 for the remaining valves.
10. Remove Tooling (A) from the cylinder head.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for
the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 10 12:53:43 UTC+0800 2019
7/7(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR TNJ
Configuration: 320E L Excavators TNJ00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
C6.6 Engines for Caterpillar Built Machines
Media Number -KENR9249-07 Publication Date -01/09/2015 Date Updated -19/06/2017
i03911451
Engine Oil Filter Base - Remove and Install
SMCS - 1306-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8760 Chain Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 1 g01980935
1. Place a suitable container below engine oil filter (5) in order to catch any oil that might be
spilled.
2. Use Tooling (A) to remove engine oil filter (5). Refer to Operation and Maintenance
Manual, "Engine Oil and Filter - Change" for the correct procedure.
3. Remove bolts (3).
Note: If bolts of different lengths are installed, identify the correct position of the bolts.
4. Remove engine oil filter base (4).
5. Remove gasket (6).
6. If necessary, remove plug (1) from engine oil filter base (4). Remove O-ring seal (2) from
plug (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
2/3(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01980935
1. Clean engine oil filter base (4). Clean the gasket surfaces of the cylinder block or the engine
oil cooler.
2. If necessary, install new O-ring seal (2) to plug (1). Install plug (1) to engine oil filter base
(4). Tighten the plug to a torque of 12 N·m (106 lb in).
3. Install bolts (3) to engine oil filter base (4).
4. Install a gasket (6) onto bolts (3). Install the assembly of the engine oil filter base to the
cylinder block or the engine oil cooler.
5. Tighten bolts (3) to a torque of 22 N·m (195 lb in).
6. Install a new engine oil filter (5) and check the level of the engine lubricating oil. Refer to
Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 10 12:54:39 UTC+0800 2019
3/3(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR TNJ
Configuration: 320E L Excavators TNJ00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
C6.6 Engines for Caterpillar Built Machines
Media Number -KENR9249-07 Publication Date -01/09/2015 Date Updated -19/06/2017
i04047714
Engine Oil Filter Base - Remove and Install - Engine Oil
Filter Base with Adapter
SMCS - 1306-010
Removal Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Removal and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/6(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g02047393
Typical example
1. Remove bolts (1), bolts (2) and bolts (3).
Note: Note the position of the bolts and the length of the bolts.
2/6(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 2 g02047397
Typical example
2. Remove adapter (6) and spacer (5) from the cylinder block. Remove gasket (4) and gasket
(8).
3. If necessary, remove split collars (7) from adapter (6).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the gasket surfaces of the adapter. Clean the gasket surfaces of the cylinder block.
3/6(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 3 g02047397
Typical example
4/6(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 4 g02047393
Typical example
2. Position new gasket (4) and gasket (8) onto adapter (6).
3. If necessary, install split collars (7) to adapter (6).
4. Install bolts (1), bolts (2) and bolts (3) to adapter (6). Install spacer (5) to applicable bolt (2).
5. Position adapter (6) to the cylinder block.
5/6(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Illustration 5 g02047413
6. Tighten bolts (1) and bolts (2) to a torque of 22 N·m (195 lb in). Tighten the bolts in the
sequence that is shown in Illustration 5.
Tighten bolts (3) in Position (X) to a torque of 44 N·m (32 lb ft). Tighten the bolts in the
sequence that is shown in Illustration 5.
7. Install the oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter Base -
Remove and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 10 12:55:35 UTC+0800 2019
6/6(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR TNJ
Configuration: 320E L Excavators TNJ00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
C6.6 Engines for Caterpillar Built Machines
Media Number -KENR9249-07 Publication Date -01/09/2015 Date Updated -19/06/2017
i03911454
Engine Oil Cooler - Remove - Engine Oil Cooler with a Low
Mounted Filter Base
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly,
"Electronic Control Module - Remove and Install" for the correct procedure.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container. Refer to Operation and
Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.
2/5(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 1 g02191813
2. If the engine has a left-hand side oil filter, remove the oil filter base. Refer to Disassembly
and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure.
If the engine has a right-hand side oil filter, follow Step 2.a through Step 2.c in order to
remove blanking plate (8).
a. Remove bolts (10).
b. Remove blanking plate (8).
c. Remove gasket (9) (not shown).
3. Remove bolt (1) from fuel injection line clamp (2). Position clamp (2) away from the engine
oil cooler assembly.
4. Cut cable straps (3) from the engine wiring harness assembly.
5. Remove plastic tube assembly (4) from crankcase breather canister (5) and the plastic tube
assembly clips.
6. Remove plastic tube assembly (12) from crankcase breather canister (5) and crankcase
breather valve (11).
7. Remove bolt (7) from bracket (6). Position bracket (6) away from the engine oil cooler.
3/5(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Illustration 2 g02191874
8. Do not remove bolts in Position (A).
9. Remove bolts (13) from engine oil cooler (14).
Note: The bolts are different lengths. Note the position of the different bolts. Note the
location and the orientation of the brackets for the tube assemblies.
10. Remove engine oil cooler assembly (14) from the cylinder block.
11. Remove gasket (15) (not shown) from engine oil cooler (14).
Illustration 3 g02191814
12. If necessary, follow Step 12.a through Step 12.c in order to disassembly the engine oil
cooler.
a. Remove bolts (16) from engine oil cooler assembly (14).
b. Remove engine oil cooler matrix (19) from spacer plate (17).
c. Remove gasket (18).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Sun Nov 10 12:56:31 UTC+0800 2019
4/5(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR TNJ
Configuration: 320E L Excavators TNJ00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
C6.6 Engines for Caterpillar Built Machines
Media Number -KENR9249-07 Publication Date -01/09/2015 Date Updated -19/06/2017
i03911457
Engine Oil Cooler - Remove - Engine Oil Cooler with a High
Mounted Filter Base
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly,
"Electronic Control Module - Remove and Install" for the correct procedure.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2019/11/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...