This document provides removal and installation procedures for various components of the heating and air conditioning system for a 320E and 320E L excavator model. The procedures include removing and installing components like the air conditioner group, refrigerant receiver-dryer, actuator motors, and control module. Safety precautions are provided, such as wearing protective equipment when working with refrigerant and not smoking in areas where refrigerant may be present. Detailed steps and illustrations are included to guide the disassembly and reassembly of each component.
Caterpillar cat 320 e excavator (prefix klt) service repair manual (klt00001 ...ujdjkkskmme
This service repair manual provides instructions for removing and installing various components of the heating and air conditioning system on a 320E and 320E L excavator. The components include the actuator motor, control module, refrigerant receiver-dryer, and various hoses and ducts. Detailed illustrations and cautions about working with refrigerant are provided to guide technicians through the disassembly and reassembly procedures.
Caterpillar cat 320 c l excavator (prefix ber) service repair manual (ber0000...yhfhjjkdksmme
The document provides instructions for removing and installing a refrigerant receiver-dryer on an excavator model 320C. Key steps include:
1. Recovering refrigerant from the air conditioning system using the proper tools.
2. Disconnecting two air conditioner hose assemblies from the refrigerant receiver-dryer by removing bolts and washers.
3. Removing the refrigerant receiver-dryer by taking out bolts and washers from the mounting bracket.
4. Installing the new refrigerant receiver-dryer by reversing the removal steps and using new O-rings on the hose assemblies.
This document provides instructions for removing and disassembling the control valve of a Caterpillar 232 Skid Steer Loader. It outlines the required tools and safety precautions. The removal process involves draining fluids, disconnecting hoses and wiring, and removing mounting bolts and brackets. The disassembly process describes removing fittings, seals, springs, spools, and other internal valve components. Proper precautions are recommended when removing pressurized or spring-loaded parts.
Caterpillar cat 262 c skid steer loader (prefix mst) service repair manual (m...ufjjsekkemmd
This document provides instructions for disassembling and assembling the control valve of a 262C Skid Steer Loader. The disassembly procedure involves removing 22 components from the control valve including hoses, nuts, cartridge assemblies, O-rings, solenoids, and springs. The assembly procedure instructs installing the components in reverse order and notes that cleanliness is important to prevent damage to precision parts. Safety precautions are provided to contain fluids and release spring forces carefully.
This document contains parts lists and diagrams for the engine and related components for a Massey Ferguson 8670 tractor with a Tier 2-3, 84 CTA engine that was phased out in 2011. It includes detailed part numbers and descriptions for the cylinder block, timing gear housing, alternator and bracket, and other engine parts. Footnotes provide additional information on specific part applications.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
Caterpillar cat 320 e excavator (prefix klt) service repair manual (klt00001 ...ujdjkkskmme
This service repair manual provides instructions for removing and installing various components of the heating and air conditioning system on a 320E and 320E L excavator. The components include the actuator motor, control module, refrigerant receiver-dryer, and various hoses and ducts. Detailed illustrations and cautions about working with refrigerant are provided to guide technicians through the disassembly and reassembly procedures.
Caterpillar cat 320 c l excavator (prefix ber) service repair manual (ber0000...yhfhjjkdksmme
The document provides instructions for removing and installing a refrigerant receiver-dryer on an excavator model 320C. Key steps include:
1. Recovering refrigerant from the air conditioning system using the proper tools.
2. Disconnecting two air conditioner hose assemblies from the refrigerant receiver-dryer by removing bolts and washers.
3. Removing the refrigerant receiver-dryer by taking out bolts and washers from the mounting bracket.
4. Installing the new refrigerant receiver-dryer by reversing the removal steps and using new O-rings on the hose assemblies.
This document provides instructions for removing and disassembling the control valve of a Caterpillar 232 Skid Steer Loader. It outlines the required tools and safety precautions. The removal process involves draining fluids, disconnecting hoses and wiring, and removing mounting bolts and brackets. The disassembly process describes removing fittings, seals, springs, spools, and other internal valve components. Proper precautions are recommended when removing pressurized or spring-loaded parts.
Caterpillar cat 262 c skid steer loader (prefix mst) service repair manual (m...ufjjsekkemmd
This document provides instructions for disassembling and assembling the control valve of a 262C Skid Steer Loader. The disassembly procedure involves removing 22 components from the control valve including hoses, nuts, cartridge assemblies, O-rings, solenoids, and springs. The assembly procedure instructs installing the components in reverse order and notes that cleanliness is important to prevent damage to precision parts. Safety precautions are provided to contain fluids and release spring forces carefully.
This document contains parts lists and diagrams for the engine and related components for a Massey Ferguson 8670 tractor with a Tier 2-3, 84 CTA engine that was phased out in 2011. It includes detailed part numbers and descriptions for the cylinder block, timing gear housing, alternator and bracket, and other engine parts. Footnotes provide additional information on specific part applications.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes detailed steps and illustrations for safely removing and replacing components like the refrigerant receiver-dryer, control module, actuator motors, and tracks. Personal protective equipment and safety precautions are emphasized when working with refrigerants. Special tools may be required and are referenced. The components are to be removed and installed in the reverse order.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...fkjsekksmem
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block using bolts. Finally, it states to install the suction pipe, gasket, and support bracket if applicable.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...fkjsekksmem
The document provides instructions for servicing the transmission of a 329D or 329D L excavator. It involves removing and disassembling the final drive, then cleaning and inspecting parts. Key steps include using various tools to remove gears, shafts, seals, and other components. Precise reassembly requires determining the correct shim thickness to preload bearings and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components on Caterpillar 320, 320L, and 320N track-type excavators, including:
1. Removing and installing inlet and exhaust valve seals from the engine cylinders.
2. Removing the engine oil filter base to access internal engine components.
3. Installing a new engine oil filter base and ensuring proper sealing.
4. Removing the engine oil cooler and associated mounting hardware.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
This document provides instructions for separating a track on a 320D LN excavator. It lists the required tools which include a chain, track block assembly, electric hydraulic pump group, hydraulic pressure gauge, pipe bushings, quick connect couplers, plugs, hoses, track press tool group, double acting cylinder, and track press rollover group. The procedure involves cleaning the exterior of the track thoroughly before disassembly to prevent dirt from entering the internal mechanism when the track is separated.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...fkjsekksmem
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...fkjsekksmem
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts and spacers. Inner and outer dust seals are installed in seal grooves on the swing gear and bearing.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...fkjsekksmem
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block using bolts. Finally, it states to install the suction pipe, gasket, and support bracket if applicable.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...fkjsekksmem
The document provides instructions for servicing the transmission of a 329D or 329D L excavator. It involves removing and disassembling the final drive, then cleaning and inspecting parts. Key steps include using various tools to remove gears, shafts, seals, and other components. Precise reassembly requires determining the correct shim thickness to preload bearings and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components on Caterpillar 320, 320L, and 320N track-type excavators, including:
1. Removing and installing inlet and exhaust valve seals from the engine cylinders.
2. Removing the engine oil filter base to access internal engine components.
3. Installing a new engine oil filter base and ensuring proper sealing.
4. Removing the engine oil cooler and associated mounting hardware.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
This document provides instructions for separating a track on a 320D LN excavator. It lists the required tools which include a chain, track block assembly, electric hydraulic pump group, hydraulic pressure gauge, pipe bushings, quick connect couplers, plugs, hoses, track press tool group, double acting cylinder, and track press rollover group. The procedure involves cleaning the exterior of the track thoroughly before disassembly to prevent dirt from entering the internal mechanism when the track is separated.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...fkjsekksmem
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...fkjsekksmem
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts and spacers. Inner and outer dust seals are installed in seal grooves on the swing gear and bearing.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04390499
Heating and Air Conditioning
SMCS - 7304; 7309; 7320
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 1. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a
Refrigerant" for the recovery and the charging procedure. Refer to Special Publication,
NENG2500, "Air Conditioning Tools" for the correct tools.
Illustration 1 g02561096
2. Disconnect hose assembly (3). Remove switch (2). Remove bolts (1).
Illustration 2 g02561097
3. Clamp hose, as shown to contain coolant. Remove hoses (4).
Illustration 3 g02561116
2/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 1. Install air conditioner group (21) in the reverse order of removal.
Disassembly Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be cleaned thoroughly. This will help to prevent dirt from entering the internal
mechanism.
Illustration 13 g02566678
1. Disconnect harness assembly (1). Remove actuator motor (2).
Illustration 14 g02566681
6/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 25 g02566681
4. Slide in core (6). Install cover (3). Install actuators motors (4). Connect harness assemblies
(5).
Illustration 26 g02566678
5. Install actuator motor (2). Connect harness assembly (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:24:18 UTC+0800 2019
10/10(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04384176
Refrigerant Receiver-Dryer
SMCS - 7322
Removal Procedure
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Recover the air conditioner refrigerant from the air conditioner system. Refer to ,
SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the
correct procedure. Refer to Dealer Service Tool Catalog, NENG2500, "Air Conditioning
Tools" for the correct tools.
Illustration 1 g02551740
2. Open the left side access door.
Illustration 2 g02551741
3. Disconnect lines (2) from the refrigerant dryer (3).
Illustration 3 g02551744
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 4. Remove clamps (4). Remove refrigerant dryer (3).
Installation Procedure
1. Install refrigerant dryer (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:25:14 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04604894
Actuator Motor (Air Distributor)
SMCS - 7304-MQ; 7309-MQ; 7320-MQ
Removal Procedure
Start By:
a. Remove the storage box and covers.
Illustration 1 g02412816
1. Remove bolts (1) and (3). Remove cover (2).
1/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 2 g02412857
2. Remove cover (4).
Illustration 3 g02412877
3. Disconnect harness assembly (5). Remove screws (7). Remove actuator (6).
Installation Procedure
1. Install actuator (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:26:10 UTC+0800 2019
2/2(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04484309
Control Module (Automatic Temperature Control Unit)
SMCS - 7304-TA; 7309-TA; 7320-TA
Removal Procedure
Illustration 1 g02235393
1. Remove cover (1) and screw. Remove cover (2).
1/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g02237715
2. Remove screws (3) from control panel (4).
Illustration 3 g02238123
3. Disconnect harness assemblies (5), (6), (7), and (8).
Illustration 4 g02238193
4. Disconnect harness assemblies (9), (10), and (11).
Illustration 5 g02238234
2/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 5. Disconnect antenna (12). Disconnect harness assemblies (13), (14), (15), and (16).
6. Remove control module (4).
Installation Procedure
1. Install control panel (4) in the reverse order of the removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:27:06 UTC+0800 2019
3/3(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610611
Track Carrier Roller
SMCS - 4154
Specifications
Illustration 1 g02593236
Table 1
Specification for 8E-5600 Track Carrier Roller
Item Qty Part Specification Description
1 1
8E-5608
Duo-
Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean and
dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The metal
seal rings must be assembled square. The rubber toric seals should not
bulge and the rubber toric seals should not twist.
A - -
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. End play:
Minimum is 0.20 mm (0.008 inch).
Maximum is 0.75 mm (0.030 inch).
2 1
6V-7661
O-Ring
Seal
Lubricate the bore of the O-ring seal lightly with the lubricant that is
being sealed.
B - -
Before assembly, length of the track roller shaft assembly that must be
free of paint is 55 ± 5 mm (2.2 ± 0.2 inch).
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8T-5255 Hydraulic Jack 1
1. Start the engine. Park the machine on a hard, level surface. Shut off the engine.
Personal injury or death can result from grease and oil coming out of
the relief valve.
Grease and oil are under high pressure coming out of the relief valve
and can penetrate the body.
Do not watch the relief valve to see if grease is escaping. Watch the track
or track adjustment cylinder to see if the track is being loosened.
Make sure the vent holes are clean before the tension is released on the
track.
Illustration 2 g00489342
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 2. Release the tension on the track.
3. Loosen relief valve (1) by one turn only. If the track does not loosen after opening the relief
valve, move the machine forward and backward until the tension is released.
Illustration 3 g00693935
4. Loosen bolt (2) that holds track carrier roller (3) to the mounting bracket on the undercarriage.
Illustration 4 g00489356
5. Position Tooling (A) and suitable cribbing under the track assembly, as shown.
6. Use Tooling (A) in order to lift the track assembly off the track carrier roller.
7. Remove track carrier roller (3). The weight of track carrier roller (3) is 17 kg (38 lb).
Reference: Refer to Undercarriage Reconditioning Bulletin, SEBF8568, "Hydraulic Excavator Roller
Disassemble and Assembly Procedures" for the Disassembly and Assembly procedures for the track
carrier roller.
Installation Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. A 8T-5255 Hydraulic Jack 1
1. Make sure that the shaft of the track carrier roller and the bore in the mounting bracket on the
undercarriage are clean and free of dirt.
Illustration 5 g00652868
(x) Mounting bracket
2. Place the track carrier roller in position in the mounting bracket. The weight of track carrier
roller is 17 kg (38 lb). Adjust the carrier roller until Distance (a), the distance between the
outside face of the mounting bracket and the carrier roller is 7.0 ± 0.5 mm (0.28 ± 0.02 inch).
Illustration 6 g00693935
3. After you adjust the position of track carrier roller (3) in the mounting bracket, tighten bolt (2).
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 7 g00489356
4. Make sure that track carrier roller (3) rotates smoothly by manually turning the carrier roller.
5. Slowly lower the track assembly onto the carrier roller with Tooling (A).
6. Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 18 23:28:01 UTC+0800 2019
5/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320E L EXCAVATOR KLT
Configuration: 320E & 320E L Excavators KLT00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
320E and 323E Excavators Machine Systems
Media Number -KENR9842-01 Publication Date -01/03/2013 Date Updated -28/03/2013
i04610953
Track Roller
SMCS - 4180
Specifications
Illustration 1 g02724642
Table 1
1/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Specification for 348-1868 Double Flange Track Roller
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2 2
7F-8268 O
-Ring Seal Lubricate the bore with the lubricant that is being sealed.
3 2
9W-2142
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
7H-3171
Pipe Plug
Apply blue Loctite 242 to the threads.
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Illustration 2 g02724638
Table 2
Specification for 206-1265 Track Roller Gp
Item Qty Part Specification Description
1 - -
Before assembly, the surfaces must be clean and free from protective
coating.
2/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 2 2 7F-8268 O
-Ring Seal
Lubricate the bore with the lubricant that is being sealed.
3 2
206-9211
Duo-Cone
Seal Gp
The rubber toric seals and all the contacting surfaces must be clean
and dry at assembly. Before assembly, apply a thin film of 6V-4876
Lubricant to the contacting surfaces of the metal seal rings. The seal
rings must be assembled square. The rubber toric seal should not bulge
and the rubber toric seal should not twist.
4 2
8E-5599
Track
Roller
Bearing
Inside diameter after assembly is 60.130 ± 0.076 mm
(2.3673 ± 0.0030 inch).
5 1
9w-2146
Plug
Apply blue Loctite 242 to the threads.
Torque to 28 ± 5 N·m (248 ± 44 lb in).
A - -
End play for the track roller shaft:
Minimum is 0.25 mm (0.010 inch).
Maximum is 1.25 mm (0.049 inch).
Removal Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Tube 2
8S-7615 Pin 2
8S-7640 Stand 2
B 183-4797 Track Roller Lifting Fork 1
Note: There is a track guide on each side of the machine. The procedure that follows is for the
removal of the track roller with the track guide.
1. Start the engine. Park the machine on a hard, level surface. Stop the engine.
2. Release the tension on the track. Refer to Operation and Maintenance Manual, "Track
Adjustment - Adjust".
3/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 3 g01211423
Note: Adjust the height of Tooling (A) in order to have sufficient clearance for the removal of
the track rollers when Tooling (A) is installed under the undercarriage (1) of the machine.
3. Lift the side of the machine. Install Tooling (A) under the undercarriage, as shown.
Illustration 4 g00664654
4. Loosen the bolts that hold track guide (2) to the undercarriage.
Note: Do not remove the bolts at this time.
Illustration 5 g00664663
4/5(W)
w
2019/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...