Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
2. any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: Cleanliness is an important factor. Before the disassembly procedure, clean the exterior of
the component . Cleaning will prevent dirt from entering the internal mechanism.
Note: Only the right pump control is equipped with the proportional reducing valve. The left
pump control starts with Step 4.
Illustration 1 g01200312
1. Remove bolts (2) , pump control (1) , and fitting (3) .
Illustration 2 g01202630
Right Pump Only
3/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 2. Remove bolts (4) . Remove proportional reducing valve (5) from pump control (1) .
Illustration 3 g01202631
Right Pump Only
3. Remove O-ring seal (9) , O-ring seal (8) , O-ring seal (7) , and O-ring seal (6) from the
proportional reducing valve.
Illustration 4 g00706166
4. Remove nut (10) from the pump control.
4/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 5 g00882598
5. Measure the length of screw (13) for installation purposes. Remove screw (13) . Remove
bolts (11) . Remove cover (12) from the pump control.
Illustration 6 g00706177
6. Remove stopper (14) from the pump control.
Illustration 7 g00706179
5/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 7. Remove O-ring seal (15) and backup ring (16) from the stopper.
8. Repeat Step 4 through Step 7 for the other side of the pump control.
Illustration 8 g00706239
9. Place the pump control in a soft jawed vise. Support pin assembly (17) . Remove piston (18)
from the pump control. Remove pin assembly (17) from the pump control.
Illustration 9 g00706243
10. Remove dowel pin (19) from the pin.
6/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 10 g00706249
11. Remove bolts (20) . Remove cover assembly (21) from the pump control.
Illustration 11 g00882599
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
7/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 12. Remove O-ring seal (28) . Remove retainer (29) . Remove O-ring seal (27) from the
retainer. Remove nut (23) and nut (25) . Remove setscrew (22) . Remove adjuster (24) .
Remove O-ring seal (26) from the adjuster.
Illustration 12 g00882601
13. Remove spring (30) and spring (31) from the pump control. Remove guide (32) from the
pump control. Remove ball (33) from the guide.
Illustration 13 g00706265
14. Remove pilot piston (34) from the pump control.
8/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 14 g00706266
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
15. Remove bolts (35) . Remove cover (36) from the pump control.
Illustration 15 g00706267
16. Remove O-ring seal (37) from the cover.
9/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 16 g00882608
17. Remove control piston (42) , spring (41) , spring (40) , spool (39) , and shims (38) from the
pump control.
Illustration 17 g00706271
18. Remove pin (43) from the pump control.
Illustration 18 g00706272
10/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 19. Remove O-ring seal (44) from the pin.
Illustration 19 g00706273
20. Remove sleeve (45) and control linkage (46) from the pump control.
Illustration 20 g00882609
21. Remove slide plate (47) and dowel (48) from the control linkage.
11/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 21 g00706275
22. Remove plugs (49) . Remove three plugs (50) from the pump control.
Illustration 22 g01200390
23. Use Tooling (A) to remove seal assembly (52) . Remove bolts (51) , bell housing (53) , and
the gasket.
Illustration 23 g01200392
24. Remove O-ring seal (54) and lip seal (55) from the seal assembly.
12/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 24 g01200457
25. Attach Tooling (C) and a suitable lifting device to head (10) . Remove bolts (56) and (57)
and head (58) . The weight of head (58) is approximately 41 kg (90 lb).
Illustration 25 g01200458
26. Remove caps (59) from nipples (62) . Remove nipples (62) , bolts (60) , and covers (61)
from head (58) .
Illustration 26 g01200459
13/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 27. Remove O-ring seal (63) from covers (61) .
Illustration 27 g01200460
28. Use Tooling (D) to remove bearings (64) from the head.
Illustration 28 g01200462
29. Remove plugs (65) and (66) from head (58) .
14/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 29 g01200471
30. Remove orifices (67) from head (58) .
Illustration 30 g01200472
31. Remove O-ring seals (68) and (69) from pump housing (72) . Remove port plates (70) and
(71) .
Note: The port plates must be installed in the original position during assembly.
15/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 34 g01200477
35. Remove plugs (79) , bolts (77) , and covers (78) from pump housing (72) .
Illustration 35 g01200481
36. Remove O-ring seal (80) from covers (78) .
Illustration 36 g01200482
37. Remove barrel assemblies (81) and (82) from pump housing (72) .
17/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Note: It may be necessary to use string to aid in the removal procedure. The barrel
assemblies must be installed in the original position during assembly.
Illustration 37 g01200485
38. Mark piston assemblies (83) and barrel (84) for assembly. Remove piston assembly (83)
from barrel (84) .
Illustration 38 g01200486
39. Remove pistons (85) from piston plate (86) .
18/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 39 g01200487
40. Remove cap (87) from barrel (84) .
Illustration 40 g01200488
41. Remove retainer (88) from barrel (84) .
Illustration 41 g01200491
42. Remove springs (89) from barrel (84) .
19/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 43. Repeat Step 38 through Step 42 for the remaining barrel assembly.
Illustration 42 g01200492
Note: The pump has been removed from Tooling (B) for photographic purposes only.
44. Use Tooling (E) to remove retaining rings (90) .
Illustration 43 g01200494
45. Remove shaft assemblies (91) and (92) from pump housing (72) .
20/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 44 g01200497
46. Use Tooling (F) and a suitable press to remove bearing (93) from shaft assembly (91) .
Illustration 45 g01200498
47. Remove ring (94) from shaft assembly (91) .
Illustration 46 g01200501
48. Use Tooling (G) and a suitable press to remove bearing (95) from shaft assembly (91) .
21/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 47 g03723277
49. Remove retaining ring (90) from shaft assembly (91) .
50. Repeat Step 46 through Step 49 for shaft (92) .
Illustration 48 g01200504
51. Remove swashplate assemblies (97) and (98) from pump housing (72) .
Note: The swashplate assemblies must be installed in the original position during assembly.
22/25(W)w
2020/2/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.