The document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator, including:
1) Removing the idler gear from the front gear group using puller tools.
2) Installing a new crankshaft rear seal using installer and locator tools, applying retaining compound to mating surfaces.
3) Removing and installing the flywheel housing which requires lifting equipment due to its weight, replacing the oil seal and dowels if damaged.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 320 d l excavator (prefix fal) service repair manual (fal0000...fusjefjskekem
This document provides instructions for removing and installing various components of a Caterpillar C6.4 engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing just the idler gear from the front gear group.
The document includes diagrams to illustrate the procedures and lists any required tools. Removal and installation steps are provided for each component.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 320 d log loader (prefix gks) service repair manual (gks00001...ufuusefjjsekkm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to:
1) Remove the flywheel housing by removing bolts and lifting it off using a lifting device.
2) Use a puller tool to remove the oil seal from the housing.
3) Install a new oil seal using the puller tool.
4) Clean surfaces, install a new gasket, and reattach the housing using bolts.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 320 d l excavator (prefix fal) service repair manual (fal0000...fusjefjskekem
This document provides instructions for removing and installing various components of a Caterpillar C6.4 engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing just the idler gear from the front gear group.
The document includes diagrams to illustrate the procedures and lists any required tools. Removal and installation steps are provided for each component.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 320 d log loader (prefix gks) service repair manual (gks00001...ufuusefjjsekkm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to:
1) Remove the flywheel housing by removing bolts and lifting it off using a lifting device.
2) Use a puller tool to remove the oil seal from the housing.
3) Install a new oil seal using the puller tool.
4) Clean surfaces, install a new gasket, and reattach the housing using bolts.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 428 f backhoe loader (prefix lbh) service repair manual (lbh0...fujsekwsxksmem
The document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a 428F backhoe loader with a C4.4 engine. It describes removing the old crankshaft rear seal using a Torx socket and installing the new seal assembly dry. It also details removing the flywheel housing bolts and dowels, checking the crankshaft rear seal for leaks, and reinstalling the housing using guide studs to align it. Proper torque values are specified for the fasteners. Additionally, the document gives directions for removing and installing the crankshaft pulley on engines both with and without an automatic belt tensioner.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 322 l excavator (prefix 9rl) service repair manual (9rl00001 ...ujfjjskkemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 322L excavator with a 3116 engine. The removal procedure involves disconnecting linkages, removing clips and pins connecting the governor. New seals are installed during reassembly. Special tools are required to compress springs and install pins. The installation procedure specifies tightening bolts in a certain sequence and adjusting the control rod for free rotation.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 320 d l excavator (prefix klm) service repair manual (klm0000...fujsjefjwekskemm
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal. Technicians are advised to keep all parts clean and free of contaminants to prevent premature wear. The instructions are part of a service manual for Caterpillar 320D and 320D L excavators.
Yamaha edl13000 te generator service repair manualfuekdksmemm
This document is a service manual for Yamaha generators that provides information to Yamaha dealers and qualified mechanics for maintenance and repairs. It assumes the user has a basic understanding of generator repair. The manual contains safety warnings and outlines how to use the manual, which provides step-by-step repair procedures organized by chapter and section. It also includes specifications, inspection procedures, troubleshooting information, and exploded diagrams.
Toro reelmaster 5410 mower service repair manualfuekdksmemm
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Reelmaster 5010 series mowers, including the 5210, 5410, 5510, and 5610 models. It covers safety instructions, product records and maintenance requirements, specifications and repairs for systems like the Kubota diesel engine, hydraulic system, electrical system, chassis, cutting units, and optional groomer. Technicians should refer to the operator's manuals for additional operating and maintenance instructions.
Toro reelmaster 3100 d mower service repair manualfuekdksmemm
This document is a service manual for the Reelmaster 3100-D that provides information for troubleshooting, testing, and repairing major systems and components. It directs technicians to refer to operator manuals for operating instructions and covers product records, the Kubota diesel engine, hydraulic system, electrical system, wheels/brakes, and cutting units. Safety practices are outlined, including only allowing trained operators to use the equipment, wearing proper protective gear, and following instructions for fueling, maintenance, and slope operation.
Toro groundsmaster 7210 service repair manualfuekdksmemm
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the Toro Groundsmaster 7200 and 7210 turf maintenance machines. It contains chapters covering safety, product records and maintenance, the Kubota diesel engine, hydraulic system, electrical system, chassis, cutting deck, and foldout diagrams. Technicians are instructed to follow safety procedures when working on the machine, including lowering the cutting deck, stopping the engine, setting the parking brake, and removing the key before servicing.
Toro groundsmaster 580 d mower service repair manualfuekdksmemm
This document provides safety instructions for operating and servicing the Groundsmaster 580-D. It outlines important safety precautions to take before operating the machine, such as reading the operator's manual and ensuring all safety devices are in place. It also describes safety measures to take while operating, such as checking that interlock switches work properly. The document advises on maintenance and service safety, such as shutting off the engine before performing any work. It emphasizes the importance of following all safety instructions to reduce the risk of injury.
Toro groundsmaster 455 d mower service repair manualfuekdksmemm
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Groundsmaster 455-D. It contains specifications, diagrams, maintenance procedures, safety instructions, and repair guides for systems like the engine, hydraulics, electrical, axles, brakes, PTO, and cutting unit. Technicians should follow all safety precautions when working on the equipment.
Toro greensmaster flex 21 service repair manualfuekdksmemm
This service manual provides information to technicians for troubleshooting, testing, and repairing components of the Greensmaster Flex 21. It contains chapters covering safety, product records, the engine, traction and reel drive systems, electrical systems, chassis, controls, cutting units, and groomers. Technicians should follow the safety instructions and refer to the manual for specifications, adjustments, and repair procedures for all machine systems.
Toro greensmaster 3050 service repair manualfuekdksmemm
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Greensmaster 3100 and 3050 golf course mowers. It contains chapters covering the engine, hydraulic system, electrical system, wheels/steering/brakes, various cutting unit types, and safety information. Technicians should follow the safety instructions when operating, maintaining or repairing the mowers to prevent injury.
Stihl ms 361 chainsaw service repair manualfuekdksmemm
This document provides specifications and repair procedures for STIHL chain saw models MS 341 and MS 361 from 2005-2012. It covers the engine, fuel system, ignition system, clutch, chain drive, and other components. Troubleshooting charts are included for issues like the clutch, ignition, carburetor and engine. The document also provides detailed instructions for repairs and replacements of parts like the cylinder, piston, crankcase, ignition module, rewind starter, and fuel system components. Tightening torques are specified for fasteners.
Stihl km 56 kombi motor service repair manualfuekdksmemm
The document provides specifications and troubleshooting information for STIHL Series 4144 engine components, including the FS 40, FS 50, FS 56, FC 56, and KM 56 models. It covers specifications for the engine, fuel system, ignition system, and tightening torques. Troubleshooting sections address issues that may occur with the clutch, rewind starter, ignition system, and carburetor. The document provides causes and remedies for various conditions that could arise with these components.
Stihl km 55 kombi motor service repair manualfuekdksmemm
This document provides specifications and service information for STIHL models FS 45, 46, 55, FC 55, HL 45, and KM 55 powerheads. It includes specifications for the fuel system, gearboxes, and tightening torques. The document also provides troubleshooting information and procedures for servicing various engine and machine components, such as the engine, rewind starter, throttle control, fuel system, drive tube, and more. Diagrams illustrate the components and procedures.
Stihl hl 45 hedge trimmer service repair manualfuekdksmemm
This document provides specifications and service information for STIHL models FS 45, 46, 55, FC 55, HL 45, and KM 55 powerheads. It includes specifications for the fuel system, gearboxes, and tightening torques. The document also provides troubleshooting information and procedures for servicing various engine and machine components, such as the engine, rewind starter, throttle control, fuel system, drive tube, and more. Diagrams illustrate the components and procedures.
Caterpillar cat 428 f backhoe loader (prefix lbh) service repair manual (lbh0...fujsekwsxksmem
The document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a 428F backhoe loader with a C4.4 engine. It describes removing the old crankshaft rear seal using a Torx socket and installing the new seal assembly dry. It also details removing the flywheel housing bolts and dowels, checking the crankshaft rear seal for leaks, and reinstalling the housing using guide studs to align it. Proper torque values are specified for the fasteners. Additionally, the document gives directions for removing and installing the crankshaft pulley on engines both with and without an automatic belt tensioner.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 322 l excavator (prefix 9rl) service repair manual (9rl00001 ...ujfjjskkemm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a 322L excavator with a 3116 engine. The removal procedure involves disconnecting linkages, removing clips and pins connecting the governor. New seals are installed during reassembly. Special tools are required to compress springs and install pins. The installation procedure specifies tightening bolts in a certain sequence and adjusting the control rod for free rotation.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 320 d l excavator (prefix klm) service repair manual (klm0000...fujsjefjwekskemm
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal. Technicians are advised to keep all parts clean and free of contaminants to prevent premature wear. The instructions are part of a service manual for Caterpillar 320D and 320D L excavators.
Yamaha edl13000 te generator service repair manualfuekdksmemm
This document is a service manual for Yamaha generators that provides information to Yamaha dealers and qualified mechanics for maintenance and repairs. It assumes the user has a basic understanding of generator repair. The manual contains safety warnings and outlines how to use the manual, which provides step-by-step repair procedures organized by chapter and section. It also includes specifications, inspection procedures, troubleshooting information, and exploded diagrams.
Toro reelmaster 5410 mower service repair manualfuekdksmemm
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Reelmaster 5010 series mowers, including the 5210, 5410, 5510, and 5610 models. It covers safety instructions, product records and maintenance requirements, specifications and repairs for systems like the Kubota diesel engine, hydraulic system, electrical system, chassis, cutting units, and optional groomer. Technicians should refer to the operator's manuals for additional operating and maintenance instructions.
Toro reelmaster 3100 d mower service repair manualfuekdksmemm
This document is a service manual for the Reelmaster 3100-D that provides information for troubleshooting, testing, and repairing major systems and components. It directs technicians to refer to operator manuals for operating instructions and covers product records, the Kubota diesel engine, hydraulic system, electrical system, wheels/brakes, and cutting units. Safety practices are outlined, including only allowing trained operators to use the equipment, wearing proper protective gear, and following instructions for fueling, maintenance, and slope operation.
Toro groundsmaster 7210 service repair manualfuekdksmemm
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the Toro Groundsmaster 7200 and 7210 turf maintenance machines. It contains chapters covering safety, product records and maintenance, the Kubota diesel engine, hydraulic system, electrical system, chassis, cutting deck, and foldout diagrams. Technicians are instructed to follow safety procedures when working on the machine, including lowering the cutting deck, stopping the engine, setting the parking brake, and removing the key before servicing.
Toro groundsmaster 580 d mower service repair manualfuekdksmemm
This document provides safety instructions for operating and servicing the Groundsmaster 580-D. It outlines important safety precautions to take before operating the machine, such as reading the operator's manual and ensuring all safety devices are in place. It also describes safety measures to take while operating, such as checking that interlock switches work properly. The document advises on maintenance and service safety, such as shutting off the engine before performing any work. It emphasizes the importance of following all safety instructions to reduce the risk of injury.
Toro groundsmaster 455 d mower service repair manualfuekdksmemm
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Groundsmaster 455-D. It contains specifications, diagrams, maintenance procedures, safety instructions, and repair guides for systems like the engine, hydraulics, electrical, axles, brakes, PTO, and cutting unit. Technicians should follow all safety precautions when working on the equipment.
Toro greensmaster flex 21 service repair manualfuekdksmemm
This service manual provides information to technicians for troubleshooting, testing, and repairing components of the Greensmaster Flex 21. It contains chapters covering safety, product records, the engine, traction and reel drive systems, electrical systems, chassis, controls, cutting units, and groomers. Technicians should follow the safety instructions and refer to the manual for specifications, adjustments, and repair procedures for all machine systems.
Toro greensmaster 3050 service repair manualfuekdksmemm
This service manual provides information for technicians to troubleshoot, test, and repair major systems and components of the Greensmaster 3100 and 3050 golf course mowers. It contains chapters covering the engine, hydraulic system, electrical system, wheels/steering/brakes, various cutting unit types, and safety information. Technicians should follow the safety instructions when operating, maintaining or repairing the mowers to prevent injury.
Stihl ms 361 chainsaw service repair manualfuekdksmemm
This document provides specifications and repair procedures for STIHL chain saw models MS 341 and MS 361 from 2005-2012. It covers the engine, fuel system, ignition system, clutch, chain drive, and other components. Troubleshooting charts are included for issues like the clutch, ignition, carburetor and engine. The document also provides detailed instructions for repairs and replacements of parts like the cylinder, piston, crankcase, ignition module, rewind starter, and fuel system components. Tightening torques are specified for fasteners.
Stihl km 56 kombi motor service repair manualfuekdksmemm
The document provides specifications and troubleshooting information for STIHL Series 4144 engine components, including the FS 40, FS 50, FS 56, FC 56, and KM 56 models. It covers specifications for the engine, fuel system, ignition system, and tightening torques. Troubleshooting sections address issues that may occur with the clutch, rewind starter, ignition system, and carburetor. The document provides causes and remedies for various conditions that could arise with these components.
Stihl km 55 kombi motor service repair manualfuekdksmemm
This document provides specifications and service information for STIHL models FS 45, 46, 55, FC 55, HL 45, and KM 55 powerheads. It includes specifications for the fuel system, gearboxes, and tightening torques. The document also provides troubleshooting information and procedures for servicing various engine and machine components, such as the engine, rewind starter, throttle control, fuel system, drive tube, and more. Diagrams illustrate the components and procedures.
Stihl hl 45 hedge trimmer service repair manualfuekdksmemm
This document provides specifications and service information for STIHL models FS 45, 46, 55, FC 55, HL 45, and KM 55 powerheads. It includes specifications for the fuel system, gearboxes, and tightening torques. The document also provides troubleshooting information and procedures for servicing various engine and machine components, such as the engine, rewind starter, throttle control, fuel system, drive tube, and more. Diagrams illustrate the components and procedures.
Stihl 4144 powerhead service repair manualfuekdksmemm
This document provides service information for STIHL powerheads in the 4144 Series, including troubleshooting, specifications, and repair procedures for the clutch, engine, ignition system, and other components. It contains detailed instructions on testing for leaks, replacing seals and gaskets, servicing the piston and crankshaft, and diagnosing and repairing ignition and engine issues. Safety precautions are noted, along with required torque specifications and the use of special servicing tools.
Stihl 036 qs chainsaw service repair manualfuekdksmemm
This document provides specifications and repair instructions for STIHL chain saw models 034, 036, and 036 QS. It includes details on the engine, fuel system, ignition system, clutch, chain brake, and other components. The document describes how to remove, install, and service parts like the cylinder, piston, crankshaft, carburetor, ignition module, and rewind starter. Tightening torques are also provided for fasteners. Illustrations demonstrate the repair steps.
Kohler courage sv715 service repair manualfuekdksmemm
This service manual provides information for servicing Kohler SV710-SV840 series engines. It includes sections on safety, maintenance, specifications, tools, troubleshooting, and disassembly/reassembly procedures. The maintenance section outlines routine maintenance tasks such as oil and filter changes and component inspections. The specifications section lists physical dimensions, torque specifications, and other technical details. Disassembly and reassembly procedures provide instructions for complete engine teardown and rebuild.
Kohler courage sv710 service repair manualfuekdksmemm
This service manual provides information on maintenance, specifications, troubleshooting, and repair procedures for Kohler SV710-SV840 engines. The manual covers safety precautions, maintenance schedules and procedures, specifications, tools required, and disassembly/reassembly procedures. Topics covered include air cleaner, fuel system, governor system, lubrication system, electrical system, starter system, emission systems, and more. Torque specifications and clearance specifications are provided for engine components.
Kohler courage sv620 vertical crankshaft engine service repair manualfuekdksmemm
This document provides a service manual for Kohler SV470-SV620 engines. It includes sections on safety, maintenance, specifications, tools, troubleshooting, and disassembly/reassembly instructions. The maintenance schedule lists tasks such as changing the oil, inspecting components, and adjusting valves. The specifications section provides engine dimensions and torque specifications for fasteners. Disassembly and reassembly instructions provide guidance on servicing the engine.
Kohler command pro cv960 vertical crankshaft service repair manualfuekdksmemm
This service manual provides information for servicing a vertical crankshaft Command Pro engine models CV940-CV1000. The manual contains 10 sections covering safety, tools, troubleshooting, air/fuel systems, electrical systems, disassembly, inspection, reassembly, and lubrication. Section 1 outlines important safety precautions to follow when servicing the engine, including warnings about rotating parts, hot parts, hazardous chemicals, explosive and toxic fumes. It also explains how to identify the engine using model, serial and specification numbers.
Kohler command cv745 vertical crankshaft engine service repair manualfuekdksmemm
This document is a service manual for the vertical crankshaft CV17-745 engine. It contains 11 sections covering safety, troubleshooting, maintenance, and repair procedures. Section 1 provides important safety information and identifies engine components. It recommends using high-quality oil and unleaded gasoline, and following a storage procedure when the engine will be inactive for over two months. The manual specifies required maintenance including changing the oil, air filter, spark plugs, and inspecting components.
Kohler command ch750 service repair manualfuekdksmemm
This document provides service information for Kohler CH18-CH25, CH620-CH730, CH740, CH750 engines including:
- Safety precautions for working on engines
- Maintenance instructions and schedule
- Engine specifications such as dimensions, oil recommendations, torque specifications
- Troubleshooting guides and repair procedures for engine systems
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 15:28:21 UTC+0800 2020
3/3(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 15:29:16 UTC+0800 2020
4/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 15:30:12 UTC+0800 2020
4/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 15:31:08 UTC+0800 2020
2/2(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 15:32:04 UTC+0800 2020
2/2(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 22 15:32:59 UTC+0800 2020
4/4(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR A8F
Configuration: 320D & 320D L Excavators A8F00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5(W)w
2020/1/22https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...