This document provides instructions for removing and installing various actuator motors and sensors for the heating and air conditioning system on a 320C excavator model. It describes in detail the removal and installation procedures for actuator motors that control the temperature air damper, front air damper, fresh air/recirculated air damper, rear window defroster damper, and front window damper. It also provides instructions for removing and installing the fan speed control and ambient air temperature sensor. The procedures include disconnecting electrical connections, removing mounting hardware, and reversing the steps for installation.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AMC
Configuration: 320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i02333043
Actuator Motor (Air Distributor) - Remove and Install
SMCS - 7304-010-MQ; 7309-010-MQ; 7320-010-MQ
Removal Procedure
Start By:
a. Remove the storage box in the cab. Refer to Disassembly and Assembly, "Storage Box and
Covers (Cab) - Remove and Install".
Removal Procedure of the Actuator Motor for the Air Damper for the
Temperature Control
Illustration 1 g00699772
1. Disconnect harness assembly (1) from the actuator motor.
1/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 2 g00699776
2. Remove screw (2) in order to disconnect linkage (3).
Illustration 3 g00699782
3. Remove screws (4) from the actuator motor.
4. Remove actuator motor (5).
Illustration 4 g00699790
5. Remove linkage (6) from the actuator motor.
2/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Removal Procedure of the Actuator Motor for the Front Air Damper
Illustration 5 g00699809
1. Disconnect harness assembly (1) from the actuator motor.
Illustration 6 g00699811
2. Remove screw (4). Remove the cable strap for the harness assembly.
3. Remove screws (2) from the actuator motor.
4. Remove actuator motor (5).
3/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 7 g00699816
5. Remove linkage (3) from the actuator motor.
Removal Procedure of the Actuator Motor for the Fresh Air or Recirculated
Air Damper
Illustration 8 g00699825
1. Disconnect harness assembly (1) from the actuator motor.
Illustration 9 g00699828
2. Remove screw (2) from the linkage.
4/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 10 g00699833
The heating and air conditioning unit is removed for photographic purposes.
3. Remove screws (3) from the actuator motor.
4. Remove actuator motor (4).
Illustration 11 g00699850
5. Remove linkage (5) from the actuator motor.
Removal Procedure of the Actuator Motor for the Air Damper for the Rear
Window Defroster
5/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 12 g00699868
1. Remove air duct (1).
Illustration 13 g00700177
Illustration 14 g00699876
The heating and air conditioning unit is removed for photographic purposes.
2. Disconnect harness assembly (2) from the actuator motor.
3. Remove cam (3) from the actuator motor.
Illustration 15 g00700179
6/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 16 g00699881
The heating and air conditioning unit is removed for photographic purposes.
4. Remove screws (4).
5. Remove actuator motor (5).
Removal Procedure of the Actuator Motor for the Air Damper for the Front
Window
Illustration 17 g00699893
1. Disconnect harness assembly (1) from the actuator motor.
7/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 18 g00699902
2. Remove screws (2).
3. Remove actuator motor (3).
Illustration 19 g00699909
4. Remove linkage (4) from the actuator motor.
Installation Procedure
Installation Procedure of the Actuator Motor for the Air Damper for the
Temperature Control
8/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 20 g00699790
1. Install linkage (6) on the actuator motor.
Illustration 21 g00699782
2. Install actuator motor (5) on the heating and air conditioning unit.
3. Install screws (4) in the actuator motor.
Illustration 22 g00699776
Note: Make sure that the linkage is properly aligned in the air actuator.
4. Connect linkage (3). Install screw (2).
9/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 23 g00699772
5. Connect harness assembly (1) to the actuator motor.
Installation Procedure of the Actuator Motor for the Front Air Damper
Illustration 24 g00699816
1. Install linkage (3) on the actuator motor.
Illustration 25 g00699811
10/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Note: Make sure that linkage (3) is properly aligned with the air actuator.
2. Install actuator motor (5).
3. Install screws (2) in the actuator motor.
4. Install a new cable strap for the harness assembly. Install screw (4).
Illustration 26 g00699809
5. Connect harness assembly (1) to the actuator motor.
Installation Procedure of the Actuator Motor for the Fresh Air or Recirculated
Air Damper
Illustration 27 g00699850
1. Install linkage (5) on the actuator motor.
11/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 28 g00699833
The heating and air conditioning unit is removed for photographic purposes.
2. Install actuator motor (4).
3. Install screws (3) in the actuator motor.
Illustration 29 g00699828
4. Connect the linkage to the air actuator.
5. Install screw (2) in the linkage.
Illustration 30 g00699825
12/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 6. Connect harness assembly (1) to the actuator motor.
Installation Procedure of the Actuator Motor for the Air Damper for the Rear
Window Defroster
Illustration 31 g00699881
The heating and air conditioning unit is removed for photographic purposes.
1. Install actuator motor (5).
2. Install screws (4).
Illustration 32 g00699876
The heating and air conditioning unit is removed for photographic purposes.
Note: Make sure that the linkages for the air dampers are installed in the cam.
3. Install cam (3) on the actuator motor.
4. Connect harness assembly (2) to the actuator motor.
13/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 33 g00699868
5. Install air duct (1).
Installation Procedure of the Actuator Motor for the Air Damper for the Front
Window
Illustration 34 g00699909
1. Install linkage (4) on the actuator motor.
Illustration 35 g00699902
14/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 2. Install actuator motor (3).
3. Install screws (2).
Illustration 36 g00699893
4. Connect harness assembly (1) to the actuator motor.
End By:
a. Install the storage box in the cab. Refer to Disassembly and Assembly, "Storage Box and
Covers (Cab) - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 6 13:15:37 UTC+0800 2019
15/15(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AMC
Configuration: 320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01917758
Speed Control - Remove and Install - Blower Linear Control
SMCS - 7311-010-X9
Removal Procedure
Start By:
a. Remove the storage box in the cab. Refer to Disassembly and Assembly, "Storage Box and
Covers (Cab) - Remove and Install".
Illustration 1 g00699585
1. Disconnect harness assembly (1) from the fan speed control.
1/3(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 2 g00699588
2. Remove screws (2) from fan speed control (3).
3. Remove fan speed control (3) from the case assembly.
Installation Procedure
Illustration 3 g00699588
1. Install fan speed control (3) in the case assembly.
2. Install screws (2) into fan speed control (3).
2/3(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 4 g00699585
3. Connect harness assembly (1) to the fan speed control.
End By:
a. Install the storage box in the cab. Refer to Disassembly and Assembly, "Storage Box and
Covers (Cab) - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 6 13:16:33 UTC+0800 2019
3/3(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AMC
Configuration: 320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01933903
Temperature Sensor (Ambient Air) - Remove and Install
SMCS - 1928-010
Removal Procedure
Illustration 1 g00695941
1. Remove bolts (2) in order to remove plate (1). The weight of plate (1) is approximately
13 kg (29 lb).
1/3(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g00698287
2. Disconnect harness assembly (3) from the ambient air temperature sensor.
Illustration 3 g00698264
3. Cut cable strap (4).
4. Remove ambient air temperature sensor (5).
Installation Procedure
Illustration 4 g00698264
2/3(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 1. Position ambient air temperature sensor (5) in the clip.
2. Install cable strap (4).
Illustration 5 g00698287
3. Connect harness assembly (3) to the ambient air temperature sensor.
Illustration 6 g00695941
4. Position plate (1) on the upper frame. The weight of plate (1) is approximately 13 kg
(29 lb).
5. Install bolts (2).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 6 13:17:29 UTC+0800 2019
3/3(W)w
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...