This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
The procedures describe disconnecting fuel lines, removing mounting bolts and other hardware, taking care to plug openings to prevent contamination. Proper tools are listed and installation is the reverse of removal. Safety notices warn to contain fluids and keep parts clean.
Caterpillar cat 320 c s 320cs excavator (prefix bcn) service repair manual (b...uujjfjkkkdmme
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
The procedures describe disconnecting fuel lines, removing mounting bolts and other hardware, taking care to plug openings to prevent contamination. Proper tools are listed and installation is the reverse of removal. Safety notices warn to contain fluids and keep parts clean.
Caterpillar cat 320 c s hydraulic excavator (prefix bmz) service repair manua...fujsekfsmemm
This document provides instructions for removing and installing fuel system components on a 320C excavator with a 3066 engine. It describes removing and installing the fuel filter base, fuel injection lines, and fuel injection nozzles. The procedures involve disconnecting fuel lines, removing mounting bolts and clamps, capping openings to prevent contamination, and reinstalling components in reverse order using new seals and following tightening specifications. Special tools are required to remove the fuel injection nozzles.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...uudfjjjskkemmd
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and secure nozzles with clamps and bolts.
Caterpillar cat 320 d l excavator (prefix cxy) service repair manual (cxy0000...ufdjjskefksmem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320D excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
Detailed step-by-step procedures are provided for each component, including required tools. Safety notices emphasize the importance of cleanliness and containing fluids. Removal and installation of each component is described in order.
New holland tc5.30 combine harvesters service repair manualujfdjjskkemme
The document is a service manual that provides technical information for servicing a TC5.30 combine. It contains sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section contains chapters that provide technical data, functional data, diagnostic data, and service procedures for the components in that section of the combine.
New holland l230 tier 4 skid steer loader service repair manual [ncm449907 ]ujfdjjskkemme
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland cx5090 laterale combine harvesters service repair manualujfdjjskkemme
This document is a service manual for CNH Industrial combine harvesters and covers the following models: CX5080 Elevation, CX5090 Elevation, CX5090 Laterale, CX5090 Hillside, CX6080 Elevation, CX6090 Elevation, and CX6090 Laterale. The manual contains sections on the engine, transmission, axles, hydraulics, brakes, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, crop storage/unloading, and the cab/bodywork. Safety information is also provided at the beginning regarding working on fluid power systems and general repair guidelines.
New holland cx820 combine harvesters service repair manualujfdjjskkemme
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
Caterpillar cat 320 c s 320cs excavator (prefix bcn) service repair manual (b...uujjfjkkkdmme
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
The procedures describe disconnecting fuel lines, removing mounting bolts and other hardware, taking care to plug openings to prevent contamination. Proper tools are listed and installation is the reverse of removal. Safety notices warn to contain fluids and keep parts clean.
Caterpillar cat 320 c s hydraulic excavator (prefix bmz) service repair manua...fujsekfsmemm
This document provides instructions for removing and installing fuel system components on a 320C excavator with a 3066 engine. It describes removing and installing the fuel filter base, fuel injection lines, and fuel injection nozzles. The procedures involve disconnecting fuel lines, removing mounting bolts and clamps, capping openings to prevent contamination, and reinstalling components in reverse order using new seals and following tightening specifications. Special tools are required to remove the fuel injection nozzles.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...uudfjjjskkemmd
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and secure nozzles with clamps and bolts.
Caterpillar cat 320 d l excavator (prefix cxy) service repair manual (cxy0000...ufdjjskefksmem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320D excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
Detailed step-by-step procedures are provided for each component, including required tools. Safety notices emphasize the importance of cleanliness and containing fluids. Removal and installation of each component is described in order.
New holland tc5.30 combine harvesters service repair manualujfdjjskkemme
The document is a service manual that provides technical information for servicing a TC5.30 combine. It contains sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section contains chapters that provide technical data, functional data, diagnostic data, and service procedures for the components in that section of the combine.
New holland l230 tier 4 skid steer loader service repair manual [ncm449907 ]ujfdjjskkemme
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland cx5090 laterale combine harvesters service repair manualujfdjjskkemme
This document is a service manual for CNH Industrial combine harvesters and covers the following models: CX5080 Elevation, CX5090 Elevation, CX5090 Laterale, CX5090 Hillside, CX6080 Elevation, CX6090 Elevation, and CX6090 Laterale. The manual contains sections on the engine, transmission, axles, hydraulics, brakes, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, crop storage/unloading, and the cab/bodywork. Safety information is also provided at the beginning regarding working on fluid power systems and general repair guidelines.
New holland cx820 combine harvesters service repair manualujfdjjskkemme
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland cx6.90 laterale fpt cursor 9 tier 4 b stage ivstage iv combine ha...ujfdjjskkemme
This service manual provides maintenance and repair information for several CNH combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains over 200 sections covering topics such as the engine, transmission, axles, hydraulics, steering, cab climate control, electrical systems, attachments/headers, and other major systems. Technicians can use this manual to find technical specifications, operational descriptions, diagnostic procedures, and service instructions for components throughout the combines.
New holland br6090 round balers service repair manualujfdjjskkemme
This service manual provides instructions for servicing a BR6080/BR6090 baler. It includes sections covering the baler's hydraulic, electrical, electronic and lubrication systems, as well as chapters on power production/transmission, axles/brakes/steering, and crop processing functions. Safety information is also provided to ensure safe repair procedures are followed.
New holland b110 backhoe loader service repair manualujfdjjskkemme
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 clr stage iv tractor loader backhoe service repair manualujfdjjskkemme
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all major systems of the machines from the engine and transmission to hydraulics, steering, and electrical systems. Each section provides information for servicing components and repairing issues. Safety precautions are outlined at the beginning regarding working on the equipment.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...ujfdjjskkemme
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, lubrication, and use of tools. It provides details on pressing parts, bolts and torque, locks, bearings, gaskets, and batteries. The goal is to correctly disassemble and reassemble machine components by following the safety guidelines and instructions.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...ujfdjjskkemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 432F backhoe loader engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and safely manipulate the valves and pistons. Proper cleaning and inspection of parts is emphasized. The installation process is essentially the reverse of removal, taking care to properly seat the valve keepers and avoid injury from the compressed springs.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...ujfdjjskkemme
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, brakes, differentials, seals and pins. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims are used to achieve proper torque specifications. Springs and pins are installed, applying grease and thread lock as needed.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...ujfdjjskkemme
This document provides assembly instructions for a 432F backhoe loader transmission. It describes assembling the transmission case and installing various components like bearings, seals, gears, shafts, and sensors. Detailed steps are given for assembling the input shaft, reverse shaft, direct drive shafts, and output shafts. The final assembly instructions describe attaching the transmission case and checking clearances on the shafts. Precautions are included for working with compressed springs.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...ujfdjjskkemme
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, requiring reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 432 e backhoe loader (prefix jba) service repair manual (jba0...ujfdjjskkemme
The document provides step-by-step instructions for disassembling the transmission of a 432E Backhoe Loader. It lists required tools and outlines the procedure for removing various transmission components including gears, shafts, bearings, seals and other parts. Detailed illustrations accompany each step to show how to use specialized tools to compress springs, remove retaining rings, and disassemble clutches, synchronizers and other mechanisms. Safety notices are included to warn of potential injury from compressed springs or other hazards.
Caterpillar cat 432 e backhoe loader (prefix bxe) service repair manual (bxe0...ujfdjjskkemme
This document provides instructions for removing and installing various engine components on a Caterpillar 432E backhoe loader, including:
- V-belts
- The fan, fan drive, and alternator
- The electric starting motor
It describes the removal and installation procedures step-by-step, including necessary tools and torque specifications for fasteners. Safety precautions are provided throughout.
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...ujfdjjskkemme
This document provides instructions for removing and installing the engine oil cooler and water pump on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to wear protective equipment and contain fluids during disassembly and reassembly.
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...ujfdjjskkemme
This document provides instructions for removing and assembling components of a Caterpillar 3054C engine, including the cylinder head. The removal procedure for the cylinder head involves first draining fluids, removing related components like the exhaust manifold and fuel injectors, and then loosening and removing mounting screws to lift the cylinder head off the engine block. Proper care is emphasized to prevent damage to parts and contain fluids during disassembly.
Caterpillar cat 322 c excavator (prefix daa) service repair manual (daa00001 ...ujfdjjskkemme
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It consists of 20 steps for disassembly and 23 steps for assembly. Key parts of the pilot valve that are disassembled include the spool assembly, springs, seals, plugs and various plates. Cleanliness is emphasized throughout the process. The assembly section provides detailed instructions on installing replacement parts and adjusting components to proper dimensions.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with a list of required tools. The removal procedure involves 11 steps that remove connecting tubes, clips, bolts and seals to detach the governor. The installation procedure reverses these steps, replacing seals and using special tools to reattach connecting pins and tubes. Proper lubrication of seals and adjustment of fuel settings are emphasized.
Caterpillar cat 320 c l excavator (prefix anb) service repair manual (anb0000...ujfdjjskkemme
The document provides instructions for removing and installing various components on a 320C excavator, including:
1) Actuator motors that control air dampers and airflow for the cabin temperature control, front air, fresh/recirculated air, rear window defroster, and front window. The procedure involves disconnecting wiring harnesses and linkages before removing screws to access each component.
2) A fan speed control unit in the case assembly, requiring disconnection of wiring and removal of screws.
3) An ambient air temperature sensor mounted on a plate, which is removed using bolts after disconnecting a wiring harness.
4) A coolant temperature sensor accessed by disconnecting a wiring
Caterpillar cat 320 c excavator (prefix sbn) service repair manual (sbn00001 ...ujfdjjskkemme
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document contains detailed step-by-step instructions accompanied by illustrations for each procedure. Safety notices are provided and required tools are listed.
Case ih stx325 steiger tractor service repair manual pin jee0102001 and afterujfdjjskkemme
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Case ih stx275 tractor service repair manualujfdjjskkemme
This document provides safety warnings and instructions for removing and installing an engine. It contains 51 steps to remove the engine, which include disconnecting batteries, draining coolant, removing hoses, wires, and other components. It then lists 40 steps to reinstall the engine, reversing the removal process and reconnecting all components. The purpose is to safely and correctly remove and replace an engine.
Case ih stx275 steiger tractor service repair manual pin jee0102001 and afterujfdjjskkemme
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
New holland cx6.90 laterale fpt cursor 9 tier 4 b stage ivstage iv combine ha...ujfdjjskkemme
This service manual provides maintenance and repair information for several CNH combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains over 200 sections covering topics such as the engine, transmission, axles, hydraulics, steering, cab climate control, electrical systems, attachments/headers, and other major systems. Technicians can use this manual to find technical specifications, operational descriptions, diagnostic procedures, and service instructions for components throughout the combines.
New holland br6090 round balers service repair manualujfdjjskkemme
This service manual provides instructions for servicing a BR6080/BR6090 baler. It includes sections covering the baler's hydraulic, electrical, electronic and lubrication systems, as well as chapters on power production/transmission, axles/brakes/steering, and crop processing functions. Safety information is also provided to ensure safe repair procedures are followed.
New holland b110 backhoe loader service repair manualujfdjjskkemme
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 clr stage iv tractor loader backhoe service repair manualujfdjjskkemme
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all major systems of the machines from the engine and transmission to hydraulics, steering, and electrical systems. Each section provides information for servicing components and repairing issues. Safety precautions are outlined at the beginning regarding working on the equipment.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...ujfdjjskkemme
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, lubrication, and use of tools. It provides details on pressing parts, bolts and torque, locks, bearings, gaskets, and batteries. The goal is to correctly disassemble and reassemble machine components by following the safety guidelines and instructions.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...ujfdjjskkemme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 432F backhoe loader engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and safely manipulate the valves and pistons. Proper cleaning and inspection of parts is emphasized. The installation process is essentially the reverse of removal, taking care to properly seat the valve keepers and avoid injury from the compressed springs.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...ujfdjjskkemme
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, brakes, differentials, seals and pins. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims are used to achieve proper torque specifications. Springs and pins are installed, applying grease and thread lock as needed.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...ujfdjjskkemme
This document provides assembly instructions for a 432F backhoe loader transmission. It describes assembling the transmission case and installing various components like bearings, seals, gears, shafts, and sensors. Detailed steps are given for assembling the input shaft, reverse shaft, direct drive shafts, and output shafts. The final assembly instructions describe attaching the transmission case and checking clearances on the shafts. Precautions are included for working with compressed springs.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...ujfdjjskkemme
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, requiring reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 432 e backhoe loader (prefix jba) service repair manual (jba0...ujfdjjskkemme
The document provides step-by-step instructions for disassembling the transmission of a 432E Backhoe Loader. It lists required tools and outlines the procedure for removing various transmission components including gears, shafts, bearings, seals and other parts. Detailed illustrations accompany each step to show how to use specialized tools to compress springs, remove retaining rings, and disassemble clutches, synchronizers and other mechanisms. Safety notices are included to warn of potential injury from compressed springs or other hazards.
Caterpillar cat 432 e backhoe loader (prefix bxe) service repair manual (bxe0...ujfdjjskkemme
This document provides instructions for removing and installing various engine components on a Caterpillar 432E backhoe loader, including:
- V-belts
- The fan, fan drive, and alternator
- The electric starting motor
It describes the removal and installation procedures step-by-step, including necessary tools and torque specifications for fasteners. Safety precautions are provided throughout.
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...ujfdjjskkemme
This document provides instructions for removing and installing the engine oil cooler and water pump on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to wear protective equipment and contain fluids during disassembly and reassembly.
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...ujfdjjskkemme
This document provides instructions for removing and assembling components of a Caterpillar 3054C engine, including the cylinder head. The removal procedure for the cylinder head involves first draining fluids, removing related components like the exhaust manifold and fuel injectors, and then loosening and removing mounting screws to lift the cylinder head off the engine block. Proper care is emphasized to prevent damage to parts and contain fluids during disassembly.
Caterpillar cat 322 c excavator (prefix daa) service repair manual (daa00001 ...ujfdjjskkemme
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It consists of 20 steps for disassembly and 23 steps for assembly. Key parts of the pilot valve that are disassembled include the spool assembly, springs, seals, plugs and various plates. Cleanliness is emphasized throughout the process. The assembly section provides detailed instructions on installing replacement parts and adjusting components to proper dimensions.
This document provides instructions for removing and installing a governor from a Caterpillar 3116 engine. It begins with a list of required tools. The removal procedure involves 11 steps that remove connecting tubes, clips, bolts and seals to detach the governor. The installation procedure reverses these steps, replacing seals and using special tools to reattach connecting pins and tubes. Proper lubrication of seals and adjustment of fuel settings are emphasized.
Caterpillar cat 320 c l excavator (prefix anb) service repair manual (anb0000...ujfdjjskkemme
The document provides instructions for removing and installing various components on a 320C excavator, including:
1) Actuator motors that control air dampers and airflow for the cabin temperature control, front air, fresh/recirculated air, rear window defroster, and front window. The procedure involves disconnecting wiring harnesses and linkages before removing screws to access each component.
2) A fan speed control unit in the case assembly, requiring disconnection of wiring and removal of screws.
3) An ambient air temperature sensor mounted on a plate, which is removed using bolts after disconnecting a wiring harness.
4) A coolant temperature sensor accessed by disconnecting a wiring
Caterpillar cat 320 c excavator (prefix sbn) service repair manual (sbn00001 ...ujfdjjskkemme
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document contains detailed step-by-step instructions accompanied by illustrations for each procedure. Safety notices are provided and required tools are listed.
Case ih stx325 steiger tractor service repair manual pin jee0102001 and afterujfdjjskkemme
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Case ih stx275 tractor service repair manualujfdjjskkemme
This document provides safety warnings and instructions for removing and installing an engine. It contains 51 steps to remove the engine, which include disconnecting batteries, draining coolant, removing hoses, wires, and other components. It then lists 40 steps to reinstall the engine, reversing the removal process and reconnecting all components. The purpose is to safely and correctly remove and replace an engine.
Case ih stx275 steiger tractor service repair manual pin jee0102001 and afterujfdjjskkemme
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564836
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/4(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813127
1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) .
Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base.
2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the
fuel filter base (2).
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Illustration 2 g00813147
3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet
manifold. Remove the fuel filter base (2) from the fuel filter bracket.
Installation Procedure
2/4(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00813147
1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two
bolts (5) that secure the fuel filter base tothe fuel filter bracket.
Illustration 4 g00813127
2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines
(4) to the fuel filter base (2) .
3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the
fuel filter by hand according to the instructions that are shown on the fuel filter. Do not
overtighten the fuel filter.
3/4(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565021
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
Start By:
A. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g00606301
The 3066 Engine is shown.
1. Remove the bolts (1), the washers, and the clamps (2), which secure the fuel lines to the
inlet manifold (3) .
Illustration 2 g00606310
2. Disconnect the fuel injection lines (4) from the fuel injection nozzles (5) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
2/5(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 3 g00606314
Fuel injection pump for a 3066 Engine
3. Disconnect the end of the fuel injection lines (4) from the fuel injection pump (6) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
4. Remove the fuel injection lines (4) from the engine.
Illustration 4 g00606317
5. Loosen the acorn nuts (7), which secure the fuel return line to the fuel injection nozzles.
6. Remove one bolt (8) and the washer from the clamp that secures the fuel return line to the
intake manifold.
Note: The clamp will remain with the fuel return line, when the fuel return line is removed
from the engine.
7. Disconnect fitting (9). Remove fuel return line (10) from the engine.
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
3/5(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 5 g00606317
1. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return
line to the fuel injection pump.
2. Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the
inlet manifold.
3. Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the
fuel injection nozzle with acorn nuts (7) .
4/5(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 6 g00606399
Fuel injection pump for a 3066 Engine
4. Place the fuel injection lines (4) on the engine.
5. Connect the fuel injection lines (4) to the fuel injection pump (6) .
6. Connect the fuel injection lines (4) to the fuel injection nozzles (5) .
Note: The fuel lines (4) should be connected at the fuel injection nozzle (5) and at the fuel
injection pump (6) before tightening the nuts for the fuel injection line.
7. Tighten the nuts for the fuel injection line to a torque of 25 N·m (18 lb ft).
Illustration 7 g00606301
Fuel lines for a 3066 Engine
8. Install the clamps (2), the washers, and the bolts (1), which secure the fuel lines to the inlet
manifold (3) .
End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:21:00 UTC+0800 2019
5/5(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151321
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 9U-6278 Adapter 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 1 g00652319
1. Remove bolt (1) and the washer that secures the clamp (2) to the cylinder head assembly.
2. Remove the clamp (2) that secures the fuel injection nozzle (3) in position in the cylinder
head assembly.
Note: Put caps or plugs on all openings immediately in order to prevent contamination in
the fuel system.
Note: Mark the clamp for later installation.
3. Install Tool (B) (not shown) to the fuel injection nozzle.
Note: Tool (B) is installed at the connection (4) for the fuel injection lines.
4. Connect Tool (A) (not shown) to Tool (B) in order to carefully remove fuel injection nozzle
(3) .
Note: Align the centerline of Tool (A) with the extended centerline of fuel injection nozzle
(3). This procedure will help prevent distortion of the fuel injection nozzle which can cause
the fuel injection nozzle to bend or break.
5. Remove the seat washer from the fuel injection nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:21:56 UTC+0800 2019
2/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151648
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00652319
1/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Install a new seat washer (5) .
2. Install fuel injection nozzle (3).
3. Install clamp (2), the washer, and bolt (1) that secures the fuel injection nozzle to the
cylinder head assembly.
4. Tighten bolt (1), that secures the fuel injection nozzle, to a torque of 22 N·m (16 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:22:51 UTC+0800 2019
2/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615152
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Illustration 1 g00618938
1. Disconnect two wire leads (1). Mark the wires for later installation.
2. Disconnect actuator lever (2) from the governor lever.
3. Remove two bolts (3) and washers that secure the fuel shutoff solenoid to the bracket.
4. Remove shutoff solenoid (4) from the bracket.
Installation Procedure
1/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 2 g00618938
1. Place the shutoff solenoid (4) in position on the bracket.
2. Install the two washers and bolts (3) that secure the fuel shutoff solenoid to the bracket.
3. Connect actuator lever (2) to the governor lever.
4. Connect two wire leads (1) to the fuel shutoff solenoid. Ensure that the wires are properly
connected.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:23:47 UTC+0800 2019
2/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:24:43 UTC+0800 2019
3/3(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:25:39 UTC+0800 2019
2/2(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 1 g00608136
1. Loosen the hose clamp (1) on hose (2) .
2. Remove hose (2) from the turbocharger (3) .
Illustration 2 g00812846
3. Disconnect oil supply line (4) from the cylinder block.
4. Loosen two clamps (5) on hose (7) .
5. Slide hose (7) off fitting (8) onto oil return line (6) .
2/3(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 3 g00608177
6. Remove eight nuts (9) from the studs on the exhaust manifold.
Note: The four studs have two nuts for a total of eight nuts.
7. Remove turbocharger (3), oil supply line (4), and oil return line (6) as an unit.
8. Remove metal gasket (10) (not shown). Check the gasket for wear or damage. Replace the
gasket, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 19:26:34 UTC+0800 2019
3/3(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BCN
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BCN00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615171
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
Illustration 1 g00608212
2. Remove two bolts (1) from the oil return line. Remove bolt (2) from the oil supply line.
3. Remove oil return line (3) from the cartridge.
4. Remove oil supply line (4) from the cartridge.
Illustration 2 g00608210
5. Remove gasket (5) from the cartridge.
6. Remove gasket (6) from the turbine housing.
2/4(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 3 g00608342
7. Remove the bolt and nut (7) from clamp (8). Remove clamp (8) that secures the turbine
housing (9) to the cartridge (10) .
8. Separate turbine housing (9) from the cartridge (10) .
Illustration 4 g00608415
Illustration 5 g00608452
3/4(W)w
2019/9/23https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...