The document provides instructions for disassembling and assembling the final drive of an excavator model 319D L. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then lists 13 steps for assembly, including installing bearings, determining shim thickness, installing seals and other components, and testing rotation. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the final drive.
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing bearings into the main housing, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...ze6074xunong
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...gongfuao7509
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps to disassemble the final drive into individual parts like the carrier assembly, ring gears, sun gear, and housing. It also includes 13 steps for reassembling the final drive, including pressing bearings into place and using shims to set the proper bearing preload. Precautions are given to clean parts thoroughly and replace all seals and gaskets.
Caterpillar Cat 319D L Excavator (Prefix WBJ) Service Repair Manual (WBJ00001...f8usiejdkmdd
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...yu5676962
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...f8seodkdmdmed3
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing bearings into the main housing, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...ze6074xunong
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...gongfuao7509
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps to disassemble the final drive into individual parts like the carrier assembly, ring gears, sun gear, and housing. It also includes 13 steps for reassembling the final drive, including pressing bearings into place and using shims to set the proper bearing preload. Precautions are given to clean parts thoroughly and replace all seals and gaskets.
Caterpillar Cat 319D L Excavator (Prefix WBJ) Service Repair Manual (WBJ00001...f8usiejdkmdd
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...yu5676962
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...f8seodkdmdmed3
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjskefksemer
The document provides disassembly and assembly instructions for the final drive of a 319D LN excavator. It describes how to disassemble the final drive components using various tools, including removing the cover, carrier assembly, ring gears, and other internal parts. It then describes the assembly process and lists the required tools, noting that cleanliness is important and all seals and gaskets should be replaced. The instructions provide details on installing each part in reverse order of disassembly and include notes on lubrication and setting proper bearing preload using shims.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...fjskefksemer
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing bearings into the main housing, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing bearings into the main housing, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 319D L Excavator (Prefix WBJ) Service Repair Manual (WBJ00001...jfkskmdmmdd
The document provides instructions for disassembling and assembling a final drive component of an excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these components in reverse order, noting that all parts must be cleaned and new seals and O-rings used. Precise measurements are taken to determine the correct shim thickness for preloading the bearings during installation in the main housing.
Caterpillar Cat 319D L Excavator (Prefix WBJ) Service Repair Manual (WBJ00001...jfkskmmdmdm
The document provides instructions for disassembling and assembling a final drive component of an excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. It then lists 13 steps for assembly, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when joining the main housing to the motor housing. Cleanliness and replacing all seals and gaskets is emphasized throughout.
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar Cat 319D L Excavator (Prefix EAW) Service Repair Manual (EAW00001...f8usiejdkmdd
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, sun gear, ring gears, and seals. It then lists 13 steps for assembly, including pressing in bearings, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. The goal is to disassemble and reassemble the final drive component, cleaning parts and replacing seals, following all safety and cleanliness procedures.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...yu5676962
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Precision cleaning and use of replacement seals, pins and gaskets is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...gongfuao7509
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, sun gear, ring gears, and seals. It then lists 13 steps for assembly, including pressing in bearings, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. The instructions include notes about cleanliness, replacing seals and O-rings, and applying lubricants during assembly.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...ze6074xunong
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. It describes in detail how to disassemble the components of the final drive such as the cover, carrier assembly, ring gears, and main housing. It lists 33 steps for disassembly. It then describes the assembly procedure and lists 13 steps, emphasizing the importance of cleanliness and replacing seals and O-rings. It instructs on preloading the bearings and determining the correct shim thickness during assembly.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...f8seodkdmdmed3
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Precision cleaning and use of replacement seals, pins and gaskets is emphasized throughout.
The document provides removal and disassembly instructions for the transmission of a 924K Wheel Loader. It details over 30 steps to remove the transmission from the machine and then disassemble the transmission components. Key parts that are disassembled include the valve assembly, housing, shafts, bearings, seals and sensors. Various tools are required including jacks, lifting devices, brackets and a bearing puller. Detailed illustrations accompany each step.
This document provides instructions for servicing components of a Caterpillar 3204 vehicular engine, including:
1. Removing and installing valve lifters, checking lifter diameter and clearance specifications.
2. Removing the oil pump and relief valve from the timing gear cover, checking bearing diameter and clearance specifications during installation.
3. Removing the timing gears and plate, identifying alignment marks and torque specifications for installation.
4. Removing and installing connecting rod bearings, checking clearances when dry.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, springs, and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the transmission.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...fujskemdidk8u
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to remove components like the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required to remove parts and release spring forces. Components must be kept in order and reinstalled in their original locations and orientations.
This document provides instructions for servicing components of a Caterpillar 3204 vehicular engine, including procedures for removing and installing valve lifters, the oil pump and relief valve, timing gears and plate, and connecting rod bearings. The document contains detailed steps for each procedure, specifications for part dimensions and clearances, and safety notices.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt contamination of parts.
More Related Content
Similar to Caterpillar Cat 319D L Excavator (Prefix ZGZ) Service Repair Manual (ZGZ00001 and up).pdf
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjskefksemer
The document provides disassembly and assembly instructions for the final drive of a 319D LN excavator. It describes how to disassemble the final drive components using various tools, including removing the cover, carrier assembly, ring gears, and other internal parts. It then describes the assembly process and lists the required tools, noting that cleanliness is important and all seals and gaskets should be replaced. The instructions provide details on installing each part in reverse order of disassembly and include notes on lubrication and setting proper bearing preload using shims.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...fjskefksemer
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing bearings into the main housing, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including pressing bearings into the main housing, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 319D L Excavator (Prefix WBJ) Service Repair Manual (WBJ00001...jfkskmdmmdd
The document provides instructions for disassembling and assembling a final drive component of an excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these components in reverse order, noting that all parts must be cleaned and new seals and O-rings used. Precise measurements are taken to determine the correct shim thickness for preloading the bearings during installation in the main housing.
Caterpillar Cat 319D L Excavator (Prefix WBJ) Service Repair Manual (WBJ00001...jfkskmmdmdm
The document provides instructions for disassembling and assembling a final drive component of an excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. It then lists 13 steps for assembly, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when joining the main housing to the motor housing. Cleanliness and replacing all seals and gaskets is emphasized throughout.
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar Cat 319D L Excavator (Prefix EAW) Service Repair Manual (EAW00001...f8usiejdkmdd
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, sun gear, ring gears, and seals. It then lists 13 steps for assembly, including pressing in bearings, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. The goal is to disassemble and reassemble the final drive component, cleaning parts and replacing seals, following all safety and cleanliness procedures.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...yu5676962
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Precision cleaning and use of replacement seals, pins and gaskets is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...gongfuao7509
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, sun gear, ring gears, and seals. It then lists 13 steps for assembly, including pressing in bearings, determining the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. The instructions include notes about cleanliness, replacing seals and O-rings, and applying lubricants during assembly.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...ze6074xunong
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. It describes in detail how to disassemble the components of the final drive such as the cover, carrier assembly, ring gears, and main housing. It lists 33 steps for disassembly. It then describes the assembly procedure and lists 13 steps, emphasizing the importance of cleanliness and replacing seals and O-rings. It instructs on preloading the bearings and determining the correct shim thickness during assembly.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...f8seodkdmdmed3
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Precision cleaning and use of replacement seals, pins and gaskets is emphasized throughout.
Similar to Caterpillar Cat 319D L Excavator (Prefix ZGZ) Service Repair Manual (ZGZ00001 and up).pdf (16)
The document provides removal and disassembly instructions for the transmission of a 924K Wheel Loader. It details over 30 steps to remove the transmission from the machine and then disassemble the transmission components. Key parts that are disassembled include the valve assembly, housing, shafts, bearings, seals and sensors. Various tools are required including jacks, lifting devices, brackets and a bearing puller. Detailed illustrations accompany each step.
This document provides instructions for servicing components of a Caterpillar 3204 vehicular engine, including:
1. Removing and installing valve lifters, checking lifter diameter and clearance specifications.
2. Removing the oil pump and relief valve from the timing gear cover, checking bearing diameter and clearance specifications during installation.
3. Removing the timing gears and plate, identifying alignment marks and torque specifications for installation.
4. Removing and installing connecting rod bearings, checking clearances when dry.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, springs, and other internal components. Cleanliness is emphasized throughout the process to prevent dirt from entering the transmission.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...fujskemdidk8u
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to remove components like the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required to remove parts and release spring forces. Components must be kept in order and reinstalled in their original locations and orientations.
This document provides instructions for servicing components of a Caterpillar 3204 vehicular engine, including procedures for removing and installing valve lifters, the oil pump and relief valve, timing gears and plate, and connecting rod bearings. The document contains detailed steps for each procedure, specifications for part dimensions and clearances, and safety notices.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions with illustrations. Some key steps include removing the torque converter, valve assemblies, gears, bearing cups, clutch groups, seals, plates, discs, retainers, springs and other internal components. Cleanliness is emphasized throughout the process to prevent dirt contamination of parts.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking components for reinstallation and preventing fluid loss.
The document provides instructions for removing and installing a cylinder head on an excavator. Key steps include:
1. Removing other engine components like the fuel filter, governor, intake and exhaust manifolds first.
2. Lifting the cylinder head off the cylinder block using bolts and carefully removing it.
3. Installing the new cylinder head by cleaning mating surfaces, applying lubricant to the gasket and bolts, and torquing bolts to specification.
Caterpillar Cat 214BFT EXCAVATOR (Prefix 4CF) Service Repair Manual (4CF00001...fujskemdidk8u
This document provides assembly instructions for governors used in 3114, 3116, and 3126 engines. It describes assembling the various governor components including the output servo assembly, fuel ratio control lever, and torque cam. Precise assembly is important as contaminants can cause rapid wear. Various tools are required to correctly position and install parts like retaining rings, pins, and seals. Proper clearances must be verified using gauges during assembly.
The document provides instructions for separating and disassembling components of a 637G wheel tractor transmission. It describes:
1. Removing the transmission, torque converter, and transfer gears by removing nuts, bolts, and clips and using lifting tools.
2. Disassembling the torque converter by removing retaining rings, seals, bearings, and internal parts like the impeller, carrier assembly, and stator using various tools.
3. Steps for disassembling parts include removing bolts, seals, races, springs, and other components from the housing, impeller, carrier assembly, stator, turbine, and hub. Detailed illustrations accompany each step.
This document provides instructions for removing and installing inlet and exhaust valve guides on a 213B excavator. The removal procedure involves using a valve guide driver tool to remove the guides from the cylinder head. For installation, the guides are tapped into position in the cylinder head and driven fully into place using the driver tool along with a guide collar. Proper cleaning is important to prevent contaminants from causing premature wear. Reusability guidelines should be followed for the valve guides.
Caterpillar Cat 14H Motor Grader (Prefix ASE) Service Repair Manual (ASE00001...fujskemdidk8u
This document provides disassembly instructions for the transmission and transfer gears of a 14H Motor Grader. It lists over 50 steps and accompanying illustrations to remove components like tubes, covers, gears, bearings, housings and more. Special tools are required to disassemble parts and remove components due to their weight, with lifting devices needed for items over 50kg. O-rings, seals and pins throughout also must be removed. Care is taken with compressed springs.
The document provides assembly instructions for governors used in 3114, 3116, and 3126 engines. It describes 15 steps to assemble the governor components, including installing the fuel ratio control lever, output servo assembly, pivot shaft, riser lever, and torque cam components. Precise assembly is required using the specified tools, with components needing to be cleaned and lubricated before installation to ensure proper governor function.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
Caterpillar Cat 12M Motor Grader (Prefix B92) Service Repair Manual (B9200001...fujskemdidk8u
This document provides disassembly instructions for the transmission of a 12M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. Key components that are disassembled include the housing, clutch assemblies, gears, seals, bearings, plates and discs. Detailed illustrations accompany each step to show how parts are configured and removed. Safety notices are included to handle parts and release spring forces.
Caterpillar Cat 12M Motor Grader (Prefix B9F) Service Repair Manual (B9F00001...fujskemdidk8u
This document provides disassembly instructions for the transmission of a 12M motor grader. It lists over 40 steps and required tools to fully disassemble the transmission. Key components that are removed include clutches, gears, seals, sensors, pistons, and housing components. Detailed illustrations accompany each step to show how to position the transmission and which fasteners and parts are involved. Safety notices are included to handle springs and contain fluids properly during disassembly.
Caterpillar Cat 12M 3 AWD MOTOR GRADER (Prefix N9B) Service Repair Manual (N9...fujskemdidk8u
This document provides instructions for disassembling the transmission of a 12M 3 AWD motor grader. It lists over 30 steps and required tools to remove components like the transmission, housing, seals, plates, sensors, clutches and gears. Diagrams illustrate each step, and notes are included to mark orientations of parts for reassembly. Safety precautions are mentioned for compressed springs.
Caterpillar Cat 340D L Excavator (Prefix JTN) Service Repair Manual (JTN00001...fujskemdidk8u
This document provides instructions for disassembling and assembling the swing drive of a 340D L excavator. The disassembly process involves removing 17 total parts from the swing drive including the cover, carrier assembly, planetary gears, ring gear and pinion shaft assembly. The assembly process describes installing 13 parts in reverse order and includes cleaning all parts, applying lubrication and anti-seize compound, and precisely positioning components using lifting tools and heat treatment.
The document provides instructions for disassembling and assembling a final drive on an excavator model 319D L. It involves removing over 30 individual parts in a specific order. Key steps include removing the final drive housing, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings, seals, shims, and aligning the main housing and motor housing, requiring precision measurements to set proper bearing preload. The process is detailed over multiple pages with illustrations to ensure correct reassembly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...fujskemdidk8u
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, with an emphasis on applying sealants, lubricants and torque specifications to reassemble components properly.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR ZGZ
Configuration: 319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i05453130
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
1/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate two ring gears (17).
Note: Two ring gears (17) are held together with Tooling (F). It may be necessary to heat
ring gears (17) in order to soften the sealant. Do not heat over 135 °C (275 °F) for more
than thirty minutes.
6/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from main housing (18) once gear (26) is removed.
Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from motor housing (28). The combined weight of main housing (18) and the final
drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 ...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:22:53 UTC+0800 2020
11/11
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 ...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR ZGZ
Configuration: 319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i05453369
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
D 439-3940 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H - Loctite C5-A Anti-Seize Lubricant
F - Loctite High Flex From-In-Place Gasket
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
1/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counter bore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
2/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8819 lb) on the
bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2205 ± 221 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y).
Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of gear (26). Take
measurements at several different locations around the gear. Compute the average of
the measured dimensions and record the number. Call this Dimension (X).
g. The thickness of the shims is equal to (X − Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
3/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18). Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28).
Illustration 7 g00708214
4/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 9. Apply Tooling (H) to the surfaces that contact pins (30).
10. Install alignment pins (30).
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26).
Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
5/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00708187
13. Install gear (26).
14. Install bolts (25) in gear (26). Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
Illustration 11 g00708186
15. Install O-ring seal (24) to main housing (18).
Illustration 12 g00708175
16. Assemble carrier assembly (15), as follows.
6/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00708220
a. Install bearings (22) in planetary gear (23).
b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 14 g00513451
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
7/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00708172
18. Install a lifting sling through the middle of carrier assembly (15). Fasten a 12.7 mm
(0.50 inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Remove the shackle and the suitable lifting device.
Illustration 16 g00713148
21. Apply Tooling (F) to the mating surface of ring gear (17b).
22. Install ring gear (17a) on ring gear (17b).
8/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 17 g00708184
23. Fasten a suitable lifting device to ring gears (17), as shown. Install the ring gears to main
housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 18 g00708325
24. Install spacer (16) in the carrier assembly.
Illustration 19 g00708162
25. Install sun gear (14) in carrier assembly (15).
9/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g01304883
Illustration 21 g00708218
26. Assemble carrier assembly (7), as follows.
a. Install bearing (12) in planetary gear (13).
b. Install thrust washers (11) and planetary gear (13) in the carrier assembly.
c. Install planetary shaft (9) in the carrier assembly.
d. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 22 g00513451
e. Orient the split in spring pin (10) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
10/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 ...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 27. Repeat Steps 26.a through 26.e in order to install the remaining planetary gears in the carrier
assembly.
Illustration 23 g00708092
28. Install carrier assembly (7) in the ring gear. The weight of carrier assembly (7) is
approximately 14 kg (30 lb).
29. Install sun gear (8) in carrier assembly (7).
30. Install spacer (6) in carrier assembly (7).
Illustration 24 g00708235
31. Install new O-ring seals (5) on plugs (4) that were in the cover.
11/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 ...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 25 g00708091
32. Install plugs (4) in cover (2). Tighten plugs (4) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
33. Install thrust plate (3) in cover (2).
34. Apply Tooling (F) to the mating surface of the ring gear.
Illustration 26 g00708090
35. Fasten Tooling (B) and a suitable lifting device to cover (2), as shown. The weight of cover
(2) is approximately 32 kg (70 lb). Install cover (2).
36. Remove Tooling (B) and install the setscrews in cover (2).
Illustration 27 g00708089
37. Install bolts (1) and the washers that hold the cover in position. Tighten bolts (1) in a
crisscross pattern.
38. Remove the final drive from Tooling (A). The combined weight of the final drive and final
drive sprocket is approximately 310 kg (683 lb).
End By:
a. Install the final drive.
12/13
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 ...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR ZGZ
Configuration: 319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i07192988
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C - Loctite C5A Copper Anti-Seize -
Table 2
Torque Values of Bolts (3)
Bolt Size Torque
M16 90 ± 15 N·m (66 ± 11 lb ft) and turn an additional angle of 60 ± 5 degrees.
M20 150 ± 25 N·m (111 ± 18 lb ft) and turn an additional angle of 55 ± 5 degrees.
M24 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional angle of 45 ± 5 degrees.
M30 500 ± 50 N·m (369 ± 37 lb ft) and turn an additional angle of 50 ± 5 degrees.
1/3
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00712767
1. Attach Tooling (B) and a suitable lifting device to final drive (1). The weight of final drive
(1) and the sprocket is approximately 312 kg (688 lb). Position the final drive in the frame.
Illustration 2 g00712737
Note: Make sure that bolt holes (2) for the travel motor are in the correct position.
Note: Make sure that bolts (3), the washers, the motor housing, and the frame are clean and
free of protective coating and oil.
2. Before assembly remove all compounds, oil, and dust from the female threads.
3. Apply Tooling (C) to the threads of bolt (3). Install bolts (3) and the washers in the final
drive. Tighten bolts (3) to a torque specified in Table 2.
4. Refer to Service Magazine, M0083843, "An Improved Bolt Tightening Procedure for the
Critical Joints Is Now Used on All Excavators" for more detail information.
5. Remove Tooling (B) and the suitable lifting device from the final drive.
2/3
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 3 g00489826
Typical Example
6. Lift the side of the machine to remove Tooling (A).
End By:
a. Install the travel motor.
b. Connect the track assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:24:52 UTC+0800 2020
3/3
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR ZGZ
Configuration: 319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i01961404
Swivel - Remove
SMCS - 5060-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
At operating temperature the implement hydraulic oil tank is hot and
under pressure. Hot oil can cause burns.
To prevent possible injury, release the pressure in the implement
hydraulic system before hydraulic lines or components are disconnected
or removed.
1/4
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 1. Release hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System
Pressure - Release".
Illustration 1 g01018978
2. Disconnect four hose assemblies (1) from the top of the swivel joint. Put plugs in the ends
of the hose assemblies in order to keep dirt and debris out of the hydraulic system.
Illustration 2 g01018979
3. Disconnect hose assemblies (2) and (3) from the swivel joint. Put plugs in the ends of the
hose assemblies in order to keep dirt and debris out of the hydraulic system.
4. Loosen and remove hose clamp (4) from the swivel joint.
2/4
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 3 g01018980
This view is beneath the machine.
5. Remove bolts (5).
6. Remove cover plate (6). Remove cover plate (7).
Illustration 4 g00360132
This view is beneath the machine.
7. Remove hose assemblies (12) from the bottom of the swivel joint. Put plugs in the ends of
the hose assemblies in order to keep dirt and debris out of the hydraulic system.
8. Remove hose assemblies (11) from the swivel joint. Put plugs in the ends of the hose
assemblies in order to keep dirt and debris out of the hydraulic system.
9. Remove hose assemblies (8) from the swivel joint. Put plugs in the ends of the hose
assemblies in order to keep dirt and debris out of the hydraulic system.
10. Remove fittings (10) in order to create extra clearance for removing the boot from the
swivel joint.
11. Remove bolts (9) and the washers that secure the swivel joint to the undercarriage of the
machine.
Illustration 5 g01019051
3/4
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. 12. Remove bolts (13) that secure flange (14) and the boot to the frame.
13. Attach a suitable lifting device onto the swivel joint and remove the swivel joint from the
machine. The weight of the swivel joint is approximately 29 kg (65 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:25:51 UTC+0800 2020
4/4
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR ZGZ
Configuration: 319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i01793734
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the swivel joint prior to disassembly.
1/2
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
34. Illustration 1 g00879932
2. Remove bolts (1) and cover (2) from outside housing (8). Remove O-ring seal (4) from
outside housing (8).
3. Remove bolts (5) and retainer (7) from rotor (9). Remove outside housing (8) from rotor (9).
4. Turn the outside housing upside-down and remove O-ring seals (6) and seals (3) from the
outside housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 31 23:26:50 UTC+0800 2020
2/2
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
35. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 319D L EXCAVATOR ZGZ
Configuration: 319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
315D, 318D and 319D Excavators Machine Systems
Media Number -KENR5272-13 Publication Date -01/09/2017 Date Updated -06/09/2017
i01793749
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
1. Make sure that all of the parts of the swivel joint are thoroughly clean and free of dirt and
debris.
Illustration 1 g00879932
2. Check the condition of seals (3) and O-ring seals (6). If the seals or O-ring seals are worn or
damaged, use new parts for replacement.
1/3
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. Illustration 2 g00917800
The number of seals may vary.
3. Install seals (3) and O-ring seals (6) in outside housing (8). Put clean hydraulic oil on seals
(3) and O-ring seals (6).
4. Install outside housing (8) over rotor (9). Install retainer (7) and bolts (5) that secure the
retainer.
5. Check the condition of O-ring seal (4). If the O-ring seal is damaged, use a new part for
replacement.
6. Apply clean hydraulic oil on O-ring seal (4). Install the O-ring seal in the outside housing.
7. Install cover (2) and bolts (1) that secure the cover.
2/3
319D L & 319D LN Excavators ZGZ00001-UP (MACHINE) POWERED BY C4.2 E...
2020/10/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...