The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators. The removal process involves using pullers to remove the camshaft gear and bearing from the camshaft. Alignment marks must be aligned during removal and installation. The installation involves heating the camshaft gear, lubricating components, and torquing bolts to specified values. Tools and safety precautions are also listed.
Caterpillar cat 318 b l excavator (prefix 3lr) service repair manual (3lr0000...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft, lifters, thrust plate and gear.
Caterpillar cat 318 b excavator (prefix 3lr) service repair manual (3lr00001 ...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft, lifters, thrust plate and gear.
Caterpillar cat 318 b ln excavator (prefix 3lr) service repair manual (3lr000...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft and related components.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...fijsekkdmdm2w
1) The document provides instructions for removing and installing the cylinder head, lifter group, and camshaft on a 3046 engine for Caterpillar built machines.
2) The cylinder head removal procedure involves removing bolts and lifting brackets to detach the head from the cylinder block.
3) Camshaft removal requires removing the timing gear cover, rocker assembly, pushrods and oil pan before using pullers to separate the camshaft gear from the shaft.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...zan2736ban
This document provides instructions for removing and installing the cylinder head and camshaft on a 3046 engine for Caterpillar built machines. Key steps include removing components like the turbocharger and fuel injectors before removing the cylinder head bolts and head. When installing, a new cylinder head gasket is used and the head bolts are tightened in a specific sequence. The camshaft removal process requires aligning timing marks and using pullers to separate the camshaft gear and bearing from the shaft.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...fujkskemdmdm4r
1) The document provides instructions for removing and installing the cylinder head, lifter group, and camshaft on a 3046 engine for Caterpillar built machines.
2) The cylinder head removal procedure involves removing bolts and lifting brackets to detach the head from the cylinder block.
3) Camshaft installation requires aligning timing marks, heating the camshaft gear, and carefully inserting the assembly into the cylinder block.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...fskekkdmdmdm3e
1) The document provides instructions for removing and installing the cylinder head, lifter group, and camshaft on a 3046 engine for Caterpillar built machines.
2) The cylinder head removal procedure involves removing bolts and lifting brackets to detach the head from the cylinder block.
3) Camshaft installation requires aligning timing marks, heating the camshaft gear, and carefully inserting the assembly into the cylinder block.
Caterpillar Cat 325D FM LL EXCAVATOR (Prefix C9M) Service Repair Manual (C9M0...jfkskmdmmdd
The document provides instructions for disassembling and assembling the final drive of a 325D FM LL EXCAVATOR. It describes removing over 30 individual parts in 16 steps for disassembly. The assembly section lists 11 steps and references tools needed. It instructs cleaning threads on the locknut and installing the locknut to complete assembly of the main housing and motor housing.
Caterpillar cat 318 b l excavator (prefix 3lr) service repair manual (3lr0000...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft, lifters, thrust plate and gear.
Caterpillar cat 318 b excavator (prefix 3lr) service repair manual (3lr00001 ...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft, lifters, thrust plate and gear.
Caterpillar cat 318 b ln excavator (prefix 3lr) service repair manual (3lr000...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft and related components.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...fijsekkdmdm2w
1) The document provides instructions for removing and installing the cylinder head, lifter group, and camshaft on a 3046 engine for Caterpillar built machines.
2) The cylinder head removal procedure involves removing bolts and lifting brackets to detach the head from the cylinder block.
3) Camshaft removal requires removing the timing gear cover, rocker assembly, pushrods and oil pan before using pullers to separate the camshaft gear from the shaft.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...zan2736ban
This document provides instructions for removing and installing the cylinder head and camshaft on a 3046 engine for Caterpillar built machines. Key steps include removing components like the turbocharger and fuel injectors before removing the cylinder head bolts and head. When installing, a new cylinder head gasket is used and the head bolts are tightened in a specific sequence. The camshaft removal process requires aligning timing marks and using pullers to separate the camshaft gear and bearing from the shaft.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...fujkskemdmdm4r
1) The document provides instructions for removing and installing the cylinder head, lifter group, and camshaft on a 3046 engine for Caterpillar built machines.
2) The cylinder head removal procedure involves removing bolts and lifting brackets to detach the head from the cylinder block.
3) Camshaft installation requires aligning timing marks, heating the camshaft gear, and carefully inserting the assembly into the cylinder block.
Caterpillar Cat 317B L and 317B LN Excavator (Prefix 6DZ) Service Repair Manu...fskekkdmdmdm3e
1) The document provides instructions for removing and installing the cylinder head, lifter group, and camshaft on a 3046 engine for Caterpillar built machines.
2) The cylinder head removal procedure involves removing bolts and lifting brackets to detach the head from the cylinder block.
3) Camshaft installation requires aligning timing marks, heating the camshaft gear, and carefully inserting the assembly into the cylinder block.
Caterpillar Cat 325D FM LL EXCAVATOR (Prefix C9M) Service Repair Manual (C9M0...jfkskmdmmdd
The document provides instructions for disassembling and assembling the final drive of a 325D FM LL EXCAVATOR. It describes removing over 30 individual parts in 16 steps for disassembly. The assembly section lists 11 steps and references tools needed. It instructs cleaning threads on the locknut and installing the locknut to complete assembly of the main housing and motor housing.
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The procedure involves removing components such as gears, shafts, seals and housings. Cleanliness is important during disassembly and assembly to prevent dirt from entering internal mechanisms. O-rings and seals should always be replaced. Bearings are pressed into place and shims are used to set the proper preload.
Caterpillar Cat 325C L Excavator (Prefix CSJ) Service Repair Manual (CSJ00001...jfkskmdmmdd
This document provides instructions for disassembling and assembling the travel motor of 325C excavator models. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly procedure consists of 26 steps and requires applying sealant and hydraulic oil, and ensuring components like keys and locating pins are correctly installed. Special care must be taken to avoid damage and keep components aligned using identification marks.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...jfkskmdmmdd
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar Cat 325D L MOBILE HYD POWER UNIT (Prefix H3N) Service Repair Manu...jfkskmdmmdd
This service manual document provides instructions for removing and installing engine components on a 325D L Mobile Hydraulic Power Unit including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document describes the required tools, removal and installation procedures, and safety notices for each component. Illustrations are provided to supplement the text instructions.
Caterpillar Cat 325D L Excavator (Prefix PKE) Service Repair Manual (PKE00001...jfkskmdmmdd
This document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Removing the final drive assembly and marking parts for reinstallation.
2. Using lifting devices and tools to remove gears, shafts, bearings, and housings.
3. Cleaning all parts thoroughly before assembly. The assembly process involves pressing bearings into place, installing seals and gears, and adjusting shims to set proper bearing preload.
Caterpillar Cat 325C L Excavator (Prefix CRB) Service Repair Manual (CRB00001...jfkskmdmmdd
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
This document provides instructions to disassemble and assemble the travel motor of a 325C excavator. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, and shaft assembly. The assembly procedure describes 21 steps and includes applying sealant, installing seals and plates, and lubricating components before assembly. Proper installation of keys and preventing the cam plate from sliding out of position are noted.
This document provides instructions to disassemble and assemble the travel motor of a 325C excavator. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, and shaft assembly. The assembly procedure describes 21 steps and includes applying sealant, installing seals and plates in the correct orientation, and using a string to correctly position components during assembly. Proper identification and positioning of parts is emphasized to ensure correct reassembly.
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to properly complete the tasks and prevent contamination of parts.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
This document provides instructions for removing and installing inlet manifold components on a Caterpillar 325B excavator engine. The summary is:
1. Remove the valve mechanism cover and disconnect any attached pipes or solenoids from the inlet manifold.
2. Remove bolts securing the inlet manifold and remove the manifold and gasket.
3. To install the new inlet manifold, position it on the engine and secure it with bolts, reattaching any pipes or solenoids. Ensure all components are clean and torque bolts to specification.
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...jfkskmdmmdd
The document provides disassembly and assembly instructions for the final drive of a 325B L excavator. It details 33 steps to disassemble the final drive components including removing carriers, gears, seals and bearings. It also outlines 28 steps for reassembling the final drive, including pressing in bearings, determining the correct shim thickness, installing seals and gears, and torquing bolts. Tools and torque specifications are provided. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the excavator's final drive system.
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...jfkskmdmmdd
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
Caterpillar Cat 325B L EXCAVATOR (Prefix 1HS) Service Repair Manual (1HS00001...jfkskmdmmdd
This document provides instructions for disassembling and assembling the travel motor of a 325B L excavator. It outlines 27 steps for disassembly, which include removing various components like the head, brake piston, barrel assembly, cam plate, and shaft assembly. It then outlines 28 steps for reassembly, instructing technicians to thoroughly clean parts, apply lubricants, and reinstall components in the reverse order of disassembly while ensuring proper alignment and torque specifications. Cautions are provided about handling components carefully and ensuring correct installation of parts like the cam plate.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual...jfkskmdmmdd
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 325-A excavator powered by a 3116 engine. It describes the required tools and gives step-by-step procedures and illustrations for removing the governor, installing a new governor, removing the fuel injection control linkage, and installing the fuel injection control linkage. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet manifold components on a Caterpillar 325B excavator engine. The summary is:
1. Remove the valve mechanism cover and disconnect any attached lines and solenoids from the inlet manifold.
2. Remove bolts securing the inlet manifold and remove the manifold and gasket.
3. To install the inlet manifold, position a new gasket and manifold on the engine and secure with bolts, reconnecting any lines and solenoids.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before installing the new gasket and bolting the cylinder head back into place. Technicians are advised to keep parts clean and contain fluids properly during the work.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual...jfkskmdmmdd
This document provides instructions for removing and installing an exhaust manifold on a 325-A excavator. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure describes applying anti-seize compound, installing new gaskets and bolts, and tightening the bolts in a specific sequence. Tools required are also listed.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmdmmdd
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a 325-A FM L EXCAVATOR 7LM. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets and locking tabs, and torquing bolts to the specified values. Tools required are also listed.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmdmmdd
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, piston shoes, shaft assembly, seals, and other components. Special care must be taken to keep components organized and mark them for proper reinstallation.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The procedure involves removing components such as gears, shafts, seals and housings. Cleanliness is important during disassembly and assembly to prevent dirt from entering internal mechanisms. O-rings and seals should always be replaced. Bearings are pressed into place and shims are used to set the proper preload.
Caterpillar Cat 325C L Excavator (Prefix CSJ) Service Repair Manual (CSJ00001...jfkskmdmmdd
This document provides instructions for disassembling and assembling the travel motor of 325C excavator models. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly procedure consists of 26 steps and requires applying sealant and hydraulic oil, and ensuring components like keys and locating pins are correctly installed. Special care must be taken to avoid damage and keep components aligned using identification marks.
Caterpillar Cat 325C MOBILE HYD POWER UNIT (Prefix MSG) Service Repair Manual...jfkskmdmmdd
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar Cat 325D L MOBILE HYD POWER UNIT (Prefix H3N) Service Repair Manu...jfkskmdmmdd
This service manual document provides instructions for removing and installing engine components on a 325D L Mobile Hydraulic Power Unit including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document describes the required tools, removal and installation procedures, and safety notices for each component. Illustrations are provided to supplement the text instructions.
Caterpillar Cat 325D L Excavator (Prefix PKE) Service Repair Manual (PKE00001...jfkskmdmmdd
This document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Removing the final drive assembly and marking parts for reinstallation.
2. Using lifting devices and tools to remove gears, shafts, bearings, and housings.
3. Cleaning all parts thoroughly before assembly. The assembly process involves pressing bearings into place, installing seals and gears, and adjusting shims to set proper bearing preload.
Caterpillar Cat 325C L Excavator (Prefix CRB) Service Repair Manual (CRB00001...jfkskmdmmdd
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
This document provides instructions to disassemble and assemble the travel motor of a 325C excavator. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, and shaft assembly. The assembly procedure describes 21 steps and includes applying sealant, installing seals and plates, and lubricating components before assembly. Proper installation of keys and preventing the cam plate from sliding out of position are noted.
This document provides instructions to disassemble and assemble the travel motor of a 325C excavator. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, and shaft assembly. The assembly procedure describes 21 steps and includes applying sealant, installing seals and plates in the correct orientation, and using a string to correctly position components during assembly. Proper identification and positioning of parts is emphasized to ensure correct reassembly.
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are outlined along with required tools and safety notices to properly complete the tasks and prevent contamination of parts.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
This document provides instructions for removing and installing inlet manifold components on a Caterpillar 325B excavator engine. The summary is:
1. Remove the valve mechanism cover and disconnect any attached pipes or solenoids from the inlet manifold.
2. Remove bolts securing the inlet manifold and remove the manifold and gasket.
3. To install the new inlet manifold, position it on the engine and secure it with bolts, reattaching any pipes or solenoids. Ensure all components are clean and torque bolts to specification.
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...jfkskmdmmdd
The document provides disassembly and assembly instructions for the final drive of a 325B L excavator. It details 33 steps to disassemble the final drive components including removing carriers, gears, seals and bearings. It also outlines 28 steps for reassembling the final drive, including pressing in bearings, determining the correct shim thickness, installing seals and gears, and torquing bolts. Tools and torque specifications are provided. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the excavator's final drive system.
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...jfkskmdmmdd
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
Caterpillar Cat 325B L EXCAVATOR (Prefix 1HS) Service Repair Manual (1HS00001...jfkskmdmmdd
This document provides instructions for disassembling and assembling the travel motor of a 325B L excavator. It outlines 27 steps for disassembly, which include removing various components like the head, brake piston, barrel assembly, cam plate, and shaft assembly. It then outlines 28 steps for reassembly, instructing technicians to thoroughly clean parts, apply lubricants, and reinstall components in the reverse order of disassembly while ensuring proper alignment and torque specifications. Cautions are provided about handling components carefully and ensuring correct installation of parts like the cam plate.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual...jfkskmdmmdd
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 325-A excavator powered by a 3116 engine. It describes the required tools and gives step-by-step procedures and illustrations for removing the governor, installing a new governor, removing the fuel injection control linkage, and installing the fuel injection control linkage. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing inlet manifold components on a Caterpillar 325B excavator engine. The summary is:
1. Remove the valve mechanism cover and disconnect any attached lines and solenoids from the inlet manifold.
2. Remove bolts securing the inlet manifold and remove the manifold and gasket.
3. To install the inlet manifold, position a new gasket and manifold on the engine and secure with bolts, reconnecting any lines and solenoids.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before installing the new gasket and bolting the cylinder head back into place. Technicians are advised to keep parts clean and contain fluids properly during the work.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual...jfkskmdmmdd
This document provides instructions for removing and installing an exhaust manifold on a 325-A excavator. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure describes applying anti-seize compound, installing new gaskets and bolts, and tightening the bolts in a specific sequence. Tools required are also listed.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmdmmdd
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a 325-A FM L EXCAVATOR 7LM. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets and locking tabs, and torquing bolts to the specified values. Tools required are also listed.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmdmmdd
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, piston shoes, shaft assembly, seals, and other components. Special care must be taken to keep components organized and mark them for proper reinstallation.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B EXCAVATOR 3LR
Configuration: 318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i02063403
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7995 Guide Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00560297
1. Clean the surfaces of the cylinder head and the cylinder block that are in contact with each
other. Ensure that the surfaces are clean and dry. Install a new, dry cylinder head gasket (3)
on the cylinder block.
Note: Do not use any sealant or gasket adhesive on the cylinder head gasket .
2. Install Tool (A) (not shown) on the cylinder block in order to install the cylinder head.
Illustration 2 g00560287
3. Attach a hoist to the cylinder head lifting brackets and install the cylinder head in position
on the cylinder block. The weight of the cylinder head assembly is 60 kg (132 lb).
4. Remove Tool (A) .
5. Apply 6V-4876 Lubricant to all of the threads and thrust faces of cylinder head bolts (1) .
Illustration 3 g00562585
2/3
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00531679
Cylinder Head Tightening Sequence
6. Install cylinder head bolts (1) and tighten all of the bolts (1 through 25) in a numerical order
according to the cylinder head tightening sequence. Tighten cylinder head bolts (1) to a
torque of 118 ± 5 N·m (87 ± 4 lb ft).
7. If necessary, install oil tube assembly (dipstick) and install bolt (2) .
End By:
a. Install the fuel injector nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Install".
b. Install the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and
Install".
c. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Install".
d. Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 29 14:10:47 UTC+0800 2020
3/3
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B EXCAVATOR 3LR
Configuration: 318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01033379
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
A. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00532246
1/3
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 2 g00532061
1. Use a magnet to remove valve lifter (1), as shown. Put identification marks on the valve
lifters for installation purposes.
2. Repeat Step 1 for the remainder of the valve lifters.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00532061
1. Put 8T-2998 Lubricant on valve lifter (1) prior to installation. Install valve lifter (1) in the
original location in the cylinder block.
2/3
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 2. Repeat Step 1 for the remainder of the valve lifters.
End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 29 14:11:46 UTC+0800 2020
3/3
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B EXCAVATOR 3LR
Configuration: 318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01597409
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure 1
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
C 1P-2321 Combination Puller 1
9S-9153 Puller Jaws 3
Start By:
A. Remove the timing gear cover. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
B. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
C. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
Note: The engine oil pan is facing in the up direction in order to retain the lifters in position for
this procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection drive
gear with the "33" mark with the "3" mark on the idler gear. Make an alignment of the "2" mark
on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the crankshaft
gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center position when
these marks are in alignment.
1. Rotate the engine at 180 degrees.
Illustration 1 g00532179
2. Use Tool (A) to remove bearing (1) from the front of camshaft gear (2) .
Note: This step is necessary only if the camshaft gear is equipped with a bearing.
2/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g00532382
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
3. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Remove
two bolts (3) and the washers that hold thrust plate (4). Carefully remove the camshaft, the
thrust plate and the camshaft gear as an assembly.
4. Remove the 12 valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove
and Install".
Illustration 3 g00532384
5. Use tool (C) to remove camshaft gear (2) from camshaft (5). Remove thrust plate (4) .
Installation Procedure 1
3/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: In this installation procedure, the engine needs to remain in the upside-down position in
order to keep the lifters in position while the camshaft is installed.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During installation, ensure that camshaft (4) is clean and lubricate all of the
components with clean engine oil.
Illustration 4 g00532385
1. Install thrust plate (4) onto camshaft (5) .
Always wear protective gloves when handling parts that have been
heated.
2. Heat camshaft gear (2) in an oven to a maximum temperature of 150 °C (302 °F) and install
camshaft gear (2) onto camshaft (5) .
3. Install the 12 valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove
and Install".
Note: During installation, ensure that the marks on the timing gears are in alignment. Align
the fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
4/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
4. Carefully install the camshaft assembly into the original location in the cylinder block.
Note: Caution must be used when the camshaft is installed in order to not damage the
camshaft lobe or the camshaft bearings.
Illustration 5 g00532382
5. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Install
two bolts (3) and the washers that hold thrust plate (4). Tighten bolts (3) to a torque of 10 to
13 N·m (7 to 10 lb ft).
6. If necessary, install the bearing onto the front of the camshaft gear.
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
b. Install the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Install".
c. Install the timing gear cover. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Removal Procedure 2
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1U-7638 Magnetic Holding Tools 12
C 1P-2321 Combination Puller 1
9S-9153 Puller Jaws 3
5/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Start By:
A. Remove the timing gear cover. Refer to Disassembly and Assembly, " Housing (Front) -
Remove".
B. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
Note: This removal procedure is done with the engine in the upright position and the valve lifters
left in the cylinder block.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
6/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 6 g00532179
The engine is rotated at 180 degrees.
1. Use Tool (A) to remove bearing (1) from the front of camshaft gear (2) .
Note: This step is necessary only if the camshaft gear is equipped with a bearing.
Illustration 7 g00534616
2. Install Tool (B) in order to hold the 12 valve lifters.
Note: Make sure that Tool (B) is holding the lifters as far up in cylinder block (6) as
possible.
Illustration 8 g00534473
Note: Be careful not to dislodge the valve lifters from Tools (B) during removal of the
camshaft.
NOTICE
7/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Do not damage the lobes or the bearings when the camshaft is removed
or installed.
3. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Remove
two bolts (3) and the washers that hold thrust plate (4). Carefully remove the camshaft, the
thrust plate and the camshaft gear as an assembly from cylinder block (6) .
Illustration 9 g00532384
4. Use tool (C) to remove camshaft gear (2) from camshaft (5). Remove thrust plate (4) .
Installation Procedure 2
Table 3
Required Tools
Tool Part Number Part Description Qty
B 1U-7638 Magnetic Holding Tools 12
Note: This installation procedure is done with the engine in the upright position and the valve
lifters left in the cylinder block.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During installation, ensure that camshaft (4) is clean and lubricate all of the
components with clean engine oil.
8/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g00532385
1. Install thrust plate (4) onto camshaft (5). Heat camshaft gear (2) to a maximum temperature
of 150 °C (302 °F) and install camshaft gear (2) onto camshaft (4) .
Note: During installation, ensure that the marks on the timing gears are in alignment. Align
the fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
2. Carefully install the camshaft assembly into the original location in the cylinder block.
Note: Caution must be used when the camshaft is installed in order to not damage the
camshaft lobe or the camshaft bearings.
Illustration 11 g00534616
Note: Make sure that Tool (B ) is holding the lifters as far up in cylinder block (6) as
possible.
9/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 12 g00534473
3. Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Install
two bolts (3) and the washers that hold thrust plate (4). Tighten bolts (3) to a torque of 10 to
13 N·m (7 to 10 lb ft).
4. If necessary, install the bearing onto the front of the camshaft gear.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
b. Install the timing gear cover. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 29 14:12:46 UTC+0800 2020
10/10
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 ...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B EXCAVATOR 3LR
Configuration: 318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i04990496
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
B. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00533094
1. Remove plug (1) from the cylinder block.
Illustration 2 g00533095
Illustration 3 g00533096
2. Use Tool (A) in order to remove the camshaft bearings from the cylinder block.
2/4
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: Refer to the instructions of the 8S-2241 Camshaft Bearing Tool Group for the proper
procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00533095
3/4
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g00533096
1. Use Tool (A) in order to install the camshaft bearings into the cylinder block. Ensure that
the oil hole of the camshaft bearings are in alignment with the oil ports in the engine block.
Note: Refer to the instructions of the 8S-2241 Camshaft Bearing Tool Group for the proper
procedure.
Illustration 6 g00533094
2. Install plug (1) into the cylinder block. Use Loctite 596 .
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
b. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 29 14:13:45 UTC+0800 2020
4/4
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318B EXCAVATOR 3LR
Configuration: 318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i05007631
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g00560680
1. Remove oil pan drain plug (3) and drain the engine oil from engine oil pan (2) .
2. Install oil pan drain plug (3) . Tighten the oil pan drain plug to a torque of 78 ± 5 N·m (57 ±
4 lb ft).
3. Remove oil tube assembly (5) .
4. Remove 30 bolts (1) and the washers from engine oil pan (2) . Remove engine oil pan (2)
and gasket (4) .
Note: A liquid gasket may be factory installed in place of an oil pan gasket.
Illustration 2 g00538955
5. Remove two bolts (7) from engine oil suction tube (6) . Remove engine oil suction tube (6) .
2/5
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g00538957
6. Check condition of O-ring seal (8) . If the O-ring seal is damaged, use a new part for
replacement.
Installation procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00538957
1. Install O-ring seal (8) on suction pipe (6) .
3/5
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 5 g00538955
2. Position engine oil suction tube (6) . Install two bolts (7) in order to secure the engine oil
suction tube .
Illustration 6 g00560680
3. Clean engine oil pan (2) .
Note: Ensure that the engine oil pan and all of the mating surfaces are free of oil and gasket
material.
4. Install gasket (4) , engine oil pan (2) , bolts (1) and the washers. Tighten the bolts to a
torque of 10 to 13 N·m (7 to 10 lb ft).
Note: Loctite 5127 may be used instead of gasket (4) . Both contact surfaces must be
completely free of oil. Apply gasket material on the cylinder block on the inside of the bolt
hole pattern in a continuous bead in order to help prevent an oil leak.
5. Install oil tube assembly (5) .
6. Fill the crankcase with engine oil to the correct level. Refer to the proper Operation and
Maintenance Manual for the correct engine oil and the correct filling procedure.
Sun Nov 29 14:14:44 UTC+0800 2020
4/5
318B L & 318B LN Excavators 3LR00001-UP (MACHINE) POWERED BY 3046 En...
2020/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...