The document provides instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 27 steps for disassembly, which include removing bolts, seals, bearings, pistons, and other components. It then lists 25 steps for assembly, which involve installing these same components in reverse order, taking care to clean parts and apply lubricants. Precautions are provided to prevent fluid loss and entry of contaminants during the process.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR AKE
Configuration: 315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959727
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer 1
C 9S-9152 Bearing Puller 1
D
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0649 Bolt 2
9X-8257 Washer 2
E 5P-0975 Plate 1
Start By:
a. Remove the piston motor (travel). Refer to Disassembly and Assembly, "Piston Motor
(Travel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on the motor and on all hose assemblies for installation purposes
and for the purpose of orientation. Plug all hose assemblies. This will help to prevent fluid loss
and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00779154
1. Remove bolts (1).
Illustration 2 g00779159
2/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Remove bolts (2) from the traction control valve in order to install Tooling (A).
Illustration 3 g00779163
3. Remove traction control valve (3) and travel motor (4) from the final drive.
Illustration 4 g00779215
4. Remove Tooling (A). Remove four bolts (2). Remove traction control valve (3).
Illustration 5 g01018464
5. Remove socket head bolts (5). Remove O-ring seal (6) and O-ring seals (7). Remove head
(8).
3/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00779238
6. Remove shim (9).
Illustration 7 g00779248
7. Remove bearing (10).
Illustration 8 g00779259
8. Remove plugs (11) and the O-ring seals.
4/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01018466
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove adapter (14) and the O-ring seal. Remove spool (13) and spring (12) from head (8).
Illustration 10 g00779279
10. Remove washer set (15).
5/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00779289
11. Remove port plate (16).
Illustration 12 g00780482
Illustration 13 g01020385
12. Remove three small O-ring seals (17). Install Tooling (D) and Tooling (E), as shown.
Tooling (E) provides a protective cover for the barrel assembly. Tooling (E) prevents
Tooling (D) from damaging the surface of the barrel assembly.
6/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 13. Retain piston (18) with Tooling (D) and apply approximately 517 kPa (75 psi) of shop air
pressure to brake release port (Y). Brake piston (18) will move out of the piston guide.
Remove brake piston (18) from the main housing.
Illustration 14 g00779307
14. Remove O-ring seal (19) and the backup ring and remove O-ring seal (20) and the backup
ring.
Illustration 15 g00779310
15. Remove piston guide (21). Remove O-ring seal (22).
Illustration 16 g00779341
7/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 16. Remove O-ring seal (23) and backup ring (24).
Illustration 17 g00779343
17. Lay the travel motor housing on one side in order to remove rotating group (25) and brake
pack (26) as a unit.
Illustration 18 g00780107
18. Remove brake pack (26).
Illustration 19 g00780290
8/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
In order to ensure that each piston assembly is installed into its original
bore, identify and mark each piston assembly, retaining plate and the
barrel before removing the piston assembly.
To avoid damage to the barrel assembly parts, do not allow the parts to
separate from the assembly during removal or installation.
19. Remove pistons (27) and retainer plate (28) from barrel (29) as a unit. Separate the pistons
from the retainer plate.
Illustration 20 g00780317
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
20. Remove guide (30), spacer (31), and nine springs (32) from the barrel.
9/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00780328
21. Remove swashplate (33).
Illustration 22 g00780348
22. Use a magnet in order to remove keys (34) and pistons (35).
Illustration 23 g00780352
23. Use a magnet in order to remove pins (36).
10/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 En...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g00780345
24. Remove shaft assembly (37). Remove plugs (38) and the O-ring seals.
Illustration 25 g01020388
25. Use Tooling (B) in order to remove seal (39).
Illustration 26 g00780494
26. Remove retaining rings (40) from each side of the bearing.
11/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 En...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 27 g00780502
27. Use a suitable press in order to remove bearing assembly (41) from shaft (42).
Illustration 28 g00780544
28. Use a suitable press and Tooling (C) in order to remove inner race (43) from shaft (42).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 23:44:38 UTC+0800 2020
12/12
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 En...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315C EXCAVATOR AKE
Configuration: 315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engine
Disassembly and Assembly
315C Excavator Machine Systems
Media Number -RENR5525-05 Publication Date -01/11/2008 Date Updated -10/11/2008
i01959745
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
F 1P-0510 Driver Group 1
G 206-3689 Turning Tool 1
H 5P-0960 Molybdenum Grease 1
Note: Replace all O-ring seals and gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00780677
1. Raise the temperature of inner race (43). Lower the temperature of shaft (42). Use a soft
hammer in order to install inner race (43) on shaft (42).
Illustration 2 g00780698
2. Raise the temperature of bearing assembly (41). Lower the temperature of shaft (42). Install
bearing assembly (41) on shaft (42).
Illustration 3 g00780494
3. Install retaining rings (40) on each side of the bearing.
2/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01018474
4. Use Tooling (F) in order to install seal (39).
Illustration 5 g00780715
5. Use a soft hammer in order to install shaft assembly (37).
Illustration 6 g00780723
6. Install plugs (38) and the O-ring seals. Tighten plugs (38) to a torque of 140 ± 14 N·m
(103 ± 10 lb ft).
3/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g00780352
7. Use a magnet in order to install pins (36).
Illustration 8 g00780839
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
8. Install pistons (34) and keys (35).
4/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 9 g00780328
9. Install swashplate (33).
Illustration 10 g00780317
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install nine springs (32), spacer (31), and guide (30) into the barrel.
5/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00780290
11. Install pistons (27) into the retainer plate (28). Install pistons (27) and retainer plate (28) as
a unit into barrel (29) .
Note: Use string in order to keep the rotating group from separating during installation.
Illustration 12 g00780870
12. Install rotating group (25).
Illustration 13 g00780887
13. Install brake pack (26).
6/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 14 g00780817
14. Install O-ring seal (23) and backup ring (24) on piston guide (21).
Illustration 15 g00779310
15. Install piston guide (21). Install O-ring seal (22).
7/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00779307
16. Install O-ring seal (19) and the backup ring and install O-ring seal (20) and the backup ring.
Illustration 17 g00797765
Note: Make sure that brake piston (18) is thoroughly clean and free of dirt and debris.
17. Install three small O-ring seals (17). Install piston (18).
Illustration 18 g00779289
18. Install port plate (16).
8/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 19 g00779279
19. Install washer set (15).
Illustration 20 g01018466
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (12) and spool (13) into head (8). Install adapter (14) and the O-ring seal into
head (8).
Illustration 21 g00779259
21. Install plugs (11) and the O-ring seals.
9/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engin...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 22 g00779248
22. Lower the temperature of bearing (10) and install bearing (10).
Illustration 23 g00779238
23. Use a shim or shims (9) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
Illustration 24 g01018475
10/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 En...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. a. Use Tooling (G) in order to turn the output shaft. The travel motor output shaft does
not rotate with an applied torque of 440 N·m (325 lb ft) with the parking brake release
port open.
Illustration 25 g01018476
b. Apply the air pressure at orifice (X). Use Tooling (G) in order to turn the output shaft
when the parking brake release port is pressurized to 780 kPa (115 psi). Perform this
procedure with the inlet port and the outlet port open to the hydraulic oil tank. The
travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or less.
Note: It may be necessary to remove head (8) several times in order to determine the correct
thickness of shim or shims (9) that are used to adjust the rolling torque of the travel motor
output shaft.
24. Apply a thin layer of Tooling (H) on shim or shims (9). Install the shim or shims on the
head. The grease will hold the shim or shims in place during the installation of the head.
Install the head on the body of the travel motor.
Illustration 26 g01018464
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
11/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 En...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. 25. Install O-ring seal (6) and O-ring seals (7). Install head (8 ). Install socket head bolts (5).
Tighten bolts (5) to a torque of 177 ± 18 N·m (131 ± 13 lb ft).
Illustration 27 g00779215
26. Install Tooling (A). Install traction control valve (3). Remove Tooling (A). Install six bolts
(2). Tighten bolts (2) to a torque of 80 ± 8 N·m (59 ± 6 lb ft).
Illustration 28 g00779163
27. Install traction control valve (3) and travel motor (4) into the final drive as a unit.
12/13
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 En...
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...