This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 23 steps to disassemble components such as the sprocket, traction control valve, barrel assembly, piston assemblies, gears, and plates. Safety notices are included to warn of hazards such as hydraulic pressure, moving parts, and released spring forces.
This document provides instructions for disassembling various components of a 313D2 excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and safety precautions, and outlines multi-step procedures to remove each part, noting how to mark components for reassembly. Detailed illustrations accompany each step to show how to properly disassemble the various systems.
This document provides instructions for disassembling and assembling components of a 313D2 excavator final drive and travel motor. It lists required tools and safety precautions, then outlines 31 steps to disassemble the final drive, travel motor, counterbalance valve, and other components. Disassembly involves removing covers, plates, gears, seals, pistons, springs and other parts. Markings are recommended to aid reassembly.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, valves, gears, plates, and seals. Safety notices are included to warn of hazards such as hydraulic pressure, heavy parts that could cause injury if dropped, and compressed springs that could propel parts if not properly released.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling various components of a 313D2 excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and safety precautions, and outlines multi-step procedures to remove each part, noting how to mark components for reassembly. Detailed illustrations accompany each step to show how to properly disassemble the various systems.
This document provides instructions for disassembling and assembling components of a 313D2 excavator final drive and travel motor. It lists required tools and safety precautions, then outlines 31 steps to disassemble the final drive, travel motor, counterbalance valve, and other components. Disassembly involves removing covers, plates, gears, seals, pistons, springs and other parts. Markings are recommended to aid reassembly.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and gives step-by-step procedures for removing components such as sprockets, valves, gears, plates, and seals. Safety notices are included to warn of hazards such as hydraulic pressure, heavy parts that could cause injury if dropped, and compressed springs that could propel parts if not properly released.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, which involves removing springs, spools, seals, and other internal components. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety notices are included regarding releasing pressures and contained fluids.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
The document provides installation instructions for a swing gear and bearing on excavator models 320D2 and 320D2 L. It outlines 22 steps to assemble the swing drive, including installing bearings, seals, gears, housings and fasteners in the proper order. Tools and lubricants required for the installation are listed in a table. The process involves lifting and positioning heavy components weighing up to 280 kg.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
1) The document provides instructions for installing a flywheel on a Caterpillar 320 GC excavator. It describes cleaning and preparing the crankshaft, installing guide studs and lifting the flywheel into place, then bolting it securely and checking the run out.
2) Additional steps are outlined for removing and installing the crankshaft rear seal and flywheel housing. The crankshaft rear seal is press-fit as a one-piece assembly and must be replaced if removed. Dowels, gaskets and seals are also installed during flywheel housing replacement.
3) Precise torques are specified for bolts depending on their grade, and alignment of the flywheel housing to the
Caterpillar Cat 318D2 L Excavator (Prefix HAH) Service Repair Manual (HAH0000...jse7039222
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents a step-by-step process involving 31 steps. Some key steps include fastening the final drive to a repair stand, removing bolts and washers to access internal components, and using various tools to separate parts like the carrier assembly, ring gears, planetary gears, and seals from the main housing. Proper cleaning and safety precautions are noted throughout.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and gives step-by-step instructions to remove components like the final drive cover, planetary assembly, retaining rings, and seals. It then describes the assembly process in reverse, including cleaning parts, replacing seals and O-rings, and torquing fasteners to the specified values. The goal is to repair or replace worn parts while maintaining cleanliness for proper functioning of the final drive.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing. Reassembly requires precisely installing seals, bearings, shims and other parts in the reverse order and verifying proper bearing preload using a press and micrometers. Cleanliness is emphasized throughout to prevent contamination.
More Related Content
Similar to Caterpillar Cat 313D2 Excavator (Prefix PLD) Service Repair Manual (PLD00001 and up).pdf
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, which involves removing springs, spools, seals, and other internal components. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety notices are included regarding releasing pressures and contained fluids.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
Similar to Caterpillar Cat 313D2 Excavator (Prefix PLD) Service Repair Manual (PLD00001 and up).pdf (9)
1. The document provides removal and installation instructions for a fuel injection pump on a 320DL excavator with a C6.4 engine.
2. The procedure describes disconnecting fuel lines and harness assemblies, removing mounting hardware, and using identification marks to ensure proper installation orientation.
3. Cleanliness is emphasized and special tools are required to disconnect the high pressure fuel lines before the pump can be removed from the engine.
Caterpillar Cat 320D2 L Excavator (Prefix DNP) Service Repair Manual (DNP0000...jse7039222
The document provides assembly and disassembly instructions for components of a 320D2 excavator, including:
- Assembling the swing drive by installing bearings, seals, gears, and housings in 22 steps.
- Removing the swing gear and bearing by lifting it from the undercarriage frame after removing bolts and seals in 6 steps.
- Providing tools, illustrations and safety notes for the procedures.
The document provides installation instructions for a swing gear and bearing on excavator models 320D2 and 320D2 L. It outlines 22 steps to assemble the swing drive, including installing bearings, seals, gears, housings and fasteners in the proper order. Tools and lubricants required for the installation are listed in a table. The process involves lifting and positioning heavy components weighing up to 280 kg.
This document provides instructions for removing and installing the valve mechanism cover base and rocker shaft on a 320D LRR excavator with a C6.4 engine. The removal procedure details removing clips, harnesses, nuts and bolts to detach the cover base. Installation involves cleaning parts, installing a new gasket, and reattaching with bolts. Separate sections provide steps for disassembling the rocker shaft into individual parts and reassembling it.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
1) The document provides instructions for installing a flywheel on a Caterpillar 320 GC excavator. It describes cleaning and preparing the crankshaft, installing guide studs and lifting the flywheel into place, then bolting it securely and checking the run out.
2) Additional steps are outlined for removing and installing the crankshaft rear seal and flywheel housing. The crankshaft rear seal is press-fit as a one-piece assembly and must be replaced if removed. Dowels, gaskets and seals are also installed during flywheel housing replacement.
3) Precise torques are specified for bolts depending on their grade, and alignment of the flywheel housing to the
Caterpillar Cat 318D2 L Excavator (Prefix HAH) Service Repair Manual (HAH0000...jse7039222
This document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents a step-by-step process involving 31 steps. Some key steps include fastening the final drive to a repair stand, removing bolts and washers to access internal components, and using various tools to separate parts like the carrier assembly, ring gears, planetary gears, and seals from the main housing. Proper cleaning and safety precautions are noted throughout.
The document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists required tools and gives step-by-step instructions to remove components like the final drive cover, planetary assembly, retaining rings, and seals. It then describes the assembly process in reverse, including cleaning parts, replacing seals and O-rings, and torquing fasteners to the specified values. The goal is to repair or replace worn parts while maintaining cleanliness for proper functioning of the final drive.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jse7039222
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel using lifting tools and removing bolts.
- Removing the crankshaft rear seal using drilling and a slide hammer puller.
- Installing a new crankshaft rear seal by applying oil and using installer tools.
- Removing the flywheel housing by lifting and removing bolts, and installing with new gaskets and bolts.
- Removing the vibration damper and crankshaft pulley by removing bolts and nuts using sockets and pullers, and installing the pulley with a washer and nut.
Caterpillar Cat 315D L Excavator (Prefix NCM) Service Repair Manual (NCM00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing. Reassembly requires precisely installing seals, bearings, shims and other parts in the reverse order and verifying proper bearing preload using a press and micrometers. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing pieces. Reassembly requires precisely installing new seals and bearings then measuring clearance to determine the correct shim thickness before reinstalling all components in reverse order. Cleanliness and applying lubricant to parts is emphasized throughout.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jse7039222
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing various components like the head, check valves, fittings, brake piston, piston guide, barrel assembly, and shaft assembly. It then lists 22 steps for assembly, covering installation of seals, plates, piston shoe assemblies, cam plate, springs, and other components in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar Cat 315D L Excavator (Prefix CJN) Service Repair Manual (CJN00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of a 315D L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, cam plate, shaft assembly and more. The assembly process has 24 steps and instructs technicians to thoroughly clean parts, apply lubricants, and reinstall components in their original positions and orientations. Technicians are warned to take care handling parts and aligning components properly to prevent damage.
Caterpillar Cat 315C L Excavator (Prefix CJC) Service Repair Manual (CJC00001...jse7039222
This document provides instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. The disassembly process involves 28 steps to remove components like bolts, seals, springs, pistons, and bearings. The assembly process reverses the disassembly steps and includes precautions like cleaning parts, applying lubricant, and ensuring proper placement of springs, seals and other components. Tools required include link brackets, slide hammers, bearing pullers, drivers and turning tools.
Caterpillar Cat 315C L Excavator (Prefix CFT) Service Repair Manual (CFT00001...jse7039222
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by using tools to remove bearings. It then lists 27 steps for assembly in reverse order, including cleaning parts, applying grease, and ensuring proper installation of seals and springs. The instructions emphasize cleanliness and using identification marks to ensure correct reinstallation of components.
Caterpillar Cat 315C L Excavator (Prefix CFB) Service Repair Manual (CFB00001...jse7039222
This document provides instructions for disassembling and assembling the final drive of a 315C excavator. The disassembly process involves removing 21 components from the final drive assembly using various tools. The assembly process describes installing the components in reverse order and determining the proper shim thickness to set the rolling torque. Precise measurements and stake marks are required to ensure correct assembly. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 315C L Excavator (Prefix ANF) Service Repair Manual (ANF00001...jse7039222
This document provides instructions for disassembling and assembling components of the rocker shaft assembly for a Caterpillar 315C excavator engine. It describes how to disassemble the rocker shaft by removing retaining rings, washers, rocker arms, and springs. It then describes the assembly process and includes illustrations showing the components. Precautions are provided regarding spring force. The document also provides instructions for installing the rocker shaft and pushrods and adjusting valve lash clearance.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR PLD
Configuration: 313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
312D2 and 313D2 Excavators Machine Systems
Media Number -UENR0196-02 Publication Date -01/11/2014 Date Updated -03/11/2014
i04126149
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly Manual ,
"Final Drive and Travel Motor - Remove".
NOTICE
1/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 2 g00940716
9. Remove valve plate (5) and O-ring seal (6).
Illustration 3 g01405139
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
Illustration 4 g01405725
4/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g01405227
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
Illustration 6 g01405232
5/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 3. Remove relief valve assemblies (12).
Illustration 7 g01405243
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 8 g01405284
Illustration 9 g01405299
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 10 g01405345
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
Illustration 11 g01405633
8/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
Illustration 12 g01405794
1. Remove O-ring seal (40) and springs (41).
9/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 13 g01405828
2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
Illustration 14 g01405855
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 15 g01405867
4. Use suitable drivers or a suitable lever to remove guide assembly (48).
Illustration 16 g01405885
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 17 g01406117
6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 18 g01406180
Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
Illustration 19 g01406210
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 20 g01406263
11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
Illustration 21 g01406329
Illustration 22 g01406338
14/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
Illustration 23 g01406376
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 24 g01406386
4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
Illustration 25 g01406397
6. Remove sun gear (68).
16/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 26 g01406400
7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
Illustration 27 g01406789
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
Illustration 28 g01406822
9. Remove sun gear (72).
17/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
Illustration 29 g01406850
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
Illustration 30 g01406853
12. Remove planetary gear (76).
18/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 31 g01406875
13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
Illustration 32 g01406882
15. Remove bolt (80) and plate (81).
19/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 33 g01406885
Illustration 34 g01406886
16. Use Tooling (H) to remove nut (82).
Illustration 35 g01406906
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 36 g01406912
19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
Illustration 37 g01407100
20. Remove both bearings (86) from housing (83).
21/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 38 g01407089
21. Remove both bearings (87) from housing (83).
Illustration 39 g01407115
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 40 g01407144
23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
Illustration 41 g01407161
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
Illustration 42 g01407166
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 21:31:59 UTC+0800 2020
23/23
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEB...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR PLD
Configuration: 313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
312D2 and 313D2 Excavators Machine Systems
Media Number -UENR0196-02 Publication Date -01/11/2014 Date Updated -03/11/2014
i07269885
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
K 1U-7558 Mounting Adapter Gp(1)
1
L - Loctite 271 -
M - Loctite High Flex GM -
N 169-0503 Installation Kit 1
P 1U-6434 Duo-Cone Seal Installer As 1
Q 4C-3761 C-Clamp 2
R FT-2766 Rolling Torque Bar 1
S - Loctite 272 -
(1)
1/24
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. The bent plates for the mounting adapter may be modified so that the mounting adapter can be assembled to the
housing.
Assembly Procedure for the Final Drive
Illustration 1 g01407166
1. Use Tooling (E) to install lip seal (91) into the body assembly.
Illustration 2 g01407561
2. Use Tooling (E), Tooling (F), and a suitable press to install bearing assembly (90) onto shaft
assembly (88).
2/24
313D2 Excavator PLD00001-UP (MACHINE) POWERED BY 3054C Engine(SEBP6...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...