This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling the components. Safety notices are included to warn of potential injuries from parts under spring pressure, hydraulic oil pressure, and hot oil. The components are to be marked for proper reassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, which involves removing springs, spools, seals, and other internal components. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, which involves removing springs, spools, seals, and other internal components. Safety precautions are provided throughout regarding releasing pressures and stored energies.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety notices are included regarding releasing pressures and contained fluids.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble the components, including draining fluids, removing covers, springs, seals, and individual parts. The goal is to disassemble the components for cleaning or replacement of worn parts prior to reassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety precautions are provided throughout regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety precautions are provided throughout regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble the components, including draining fluids, removing covers, springs, seals, and individual parts. The goal is to disassemble the components for cleaning or replacement of worn parts prior to reassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
CASE IH Rowtrac 370 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Quadtrac 620 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 580 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 540 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repair.
CASE IH Quadtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
More Related Content
Similar to Caterpillar Cat 312D2 GC Excavator (Prefix RXZ) Service Repair Manual (RXZ00001 and up).pdf
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, including removing covers, gears, and plates. It also provides 13 steps to disassemble the travel motor, such as removing piston assemblies, seals, and guides. Additionally, it lists 16 steps to disassemble the counterbalance valve, including removing springs, spools, and relief valve assemblies. Safety notices are included regarding releasing pressures and contained fluids.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble the components, including draining fluids, removing covers, springs, seals, and individual parts. The goal is to disassemble the components for cleaning or replacement of worn parts prior to reassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety precautions are provided throughout regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety precautions are provided throughout regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and safety precautions and outlines 16 steps to disassemble the components, including draining fluids, removing covers, springs, seals, and individual parts. The goal is to disassemble the components for cleaning or replacement of worn parts prior to reassembly.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
Similar to Caterpillar Cat 312D2 GC Excavator (Prefix RXZ) Service Repair Manual (RXZ00001 and up).pdf (17)
CASE IH Rowtrac 370 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Quadtrac 620 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 580 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 540 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repair.
CASE IH Quadtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 470 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repairs.
CASE IH PUMA 210 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual that contains information on the distribution systems for a tractor model. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, pneumatic system, electrical and electronic systems. It provides information on special tools needed for maintenance and repair of components within these various systems.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding part orientations, identification marks and keys to ensure correct reassembly.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...f8usejkddmmd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, pulley, oil pan, gears, and pump.
2. Disconnecting a harness, cutting a cable strap, and removing bolts to detach a bypass tube.
3. Removing bolts of different lengths to separate the front housing from the engine. Care must be taken to properly contain fluids.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of hazards like released spring forces, hot or pressurized components, and ensuring fluids are contained. Required specialty tools are listed at the start for tasks like removing bearings, pistons, and other parts.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
CASE IH PUMA 195 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH PUMA tractors that contains sections covering the tractor's distribution systems, power systems (primary hydraulic, secondary hydraulic, pneumatic, electrical), electronic systems, power production systems (engine, fuel injection, air intake, exhaust, cooling, lubrication, starting), powertrain (transmission, reducers, PTOs), travelling systems (axles, steering, brakes, suspension, wheels), body and structure, user platform, environment control, and working arm/hitch. The introduction provides safety rules for working on the tractor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, and bearings. It then details 19 steps to disassemble the travel motor, removing seals, plates, pistons, and the barrel assembly. Safety cautions are provided throughout regarding contained fluids, pressurized components, and released spring forces.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 313D excavator. It lists the required tools and outlines 20 steps to disassemble the components. These include draining fluids, removing covers, plates, seals, springs, pistons, and other parts. Safety precautions are provided to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...f8usejkddmmd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety cautions are provided throughout regarding releasing pressures and spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump positions using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...f8usejkddmmd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It describes:
1) Cleaning and heating the ring gear to install it on the flywheel.
2) Positioning the flywheel in the housing with guide bolts and lifting brackets, and tightening the bolts to specification.
3) Checking flywheel alignment after installation.
4) Removing the crankshaft rear seal housing assembly by removing setscrews.
5) Installing the new crankshaft rear seal housing assembly with a plastic sleeve, aligning it, and tightening setscrews to specification.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 GC EXCAVATOR RXZ
Configuration: 312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
312D2 and 313D2 Excavators Machine Systems
Media Number -UENR0196-02 Publication Date -01/11/2014 Date Updated -03/11/2014
i04126149
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly Manual ,
"Final Drive and Travel Motor - Remove".
NOTICE
1/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g00940716
9. Remove valve plate (5) and O-ring seal (6).
Illustration 3 g01405139
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
Illustration 4 g01405725
4/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g01405227
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
Illustration 6 g01405232
5/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. Remove relief valve assemblies (12).
Illustration 7 g01405243
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 8 g01405284
Illustration 9 g01405299
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 10 g01405345
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
Illustration 11 g01405633
8/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
Illustration 12 g01405794
1. Remove O-ring seal (40) and springs (41).
9/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 13 g01405828
2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
Illustration 14 g01405855
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 15 g01405867
4. Use suitable drivers or a suitable lever to remove guide assembly (48).
Illustration 16 g01405885
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 17 g01406117
6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 18 g01406180
Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
Illustration 19 g01406210
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 20 g01406263
11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
Illustration 21 g01406329
Illustration 22 g01406338
14/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
Illustration 23 g01406376
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 24 g01406386
4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
Illustration 25 g01406397
6. Remove sun gear (68).
16/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 26 g01406400
7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
Illustration 27 g01406789
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
Illustration 28 g01406822
9. Remove sun gear (72).
17/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
Illustration 29 g01406850
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
Illustration 30 g01406853
12. Remove planetary gear (76).
18/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 31 g01406875
13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
Illustration 32 g01406882
15. Remove bolt (80) and plate (81).
19/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 33 g01406885
Illustration 34 g01406886
16. Use Tooling (H) to remove nut (82).
Illustration 35 g01406906
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 36 g01406912
19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
Illustration 37 g01407100
20. Remove both bearings (86) from housing (83).
21/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 38 g01407089
21. Remove both bearings (87) from housing (83).
Illustration 39 g01407115
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 40 g01407144
23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
Illustration 41 g01407161
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
Illustration 42 g01407166
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 00:49:15 UTC+0800 2020
23/23
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 GC EXCAVATOR RXZ
Configuration: 312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
312D2 and 313D2 Excavators Machine Systems
Media Number -UENR0196-02 Publication Date -01/11/2014 Date Updated -03/11/2014
i07269885
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
K 1U-7558 Mounting Adapter Gp(1)
1
L - Loctite 271 -
M - Loctite High Flex GM -
N 169-0503 Installation Kit 1
P 1U-6434 Duo-Cone Seal Installer As 1
Q 4C-3761 C-Clamp 2
R FT-2766 Rolling Torque Bar 1
S - Loctite 272 -
(1)
1/24
312D2 GC Excavator RXZ00001-UP (MACHINE) POWERED BY 3054C Engine(SE...
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...