The document provides instructions for removing and installing a fuel injection pump and turbocharger on a Caterpillar 3064 engine. The procedure includes removing fuel lines, bolts, and gears to remove the pump, and aligning marks to ensure proper installation. To remove the turbocharger, hoses and lines must be disconnected and nuts removed. Disassembly of the turbocharger involves separating housing components after removing bolts, nuts and gaskets.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the heavy fuel injection pump from the engine.
3. Removing hoses and bolts to detach the turbocharger, oil lines, and exhaust manifold as a single unit from the engine.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil lines from the turbocharger.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...tuzhiyou2
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...qfyc504378
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...lituo39419496
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the fuel injection pump from the engine block.
3. Removing hoses and lines connected to the turbocharger, then removing nuts to separate the turbocharger from the exhaust manifold.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil supply and return lines.
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...zan2736ban
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Cleaning the crankshaft and applying retaining compound to the mating surfaces.
2) Using a installer tool to push the new seal onto the crankshaft until it bottoms out.
3) Removing the tool and checking that the seal is correctly installed.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the heavy fuel injection pump from the engine.
3. Removing hoses and bolts to detach the turbocharger, oil lines, and exhaust manifold as a single unit from the engine.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil lines from the turbocharger.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...tuzhiyou2
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...qfyc504378
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...lituo39419496
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the fuel injection pump from the engine block.
3. Removing hoses and lines connected to the turbocharger, then removing nuts to separate the turbocharger from the exhaust manifold.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil supply and return lines.
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...zan2736ban
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Cleaning the crankshaft and applying retaining compound to the mating surfaces.
2) Using a installer tool to push the new seal onto the crankshaft until it bottoms out.
3) Removing the tool and checking that the seal is correctly installed.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...fusjekkdmdmd2w
The documents provide instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
1. Installing the flywheel, which involves heating the ring gear, cleaning parts, using guide bolts and lifting devices, and tightening bolts to the specified torque.
2. Removing the crankshaft rear seal, which is non-serviceable, requiring replacement of the entire housing assembly after removing setscrews.
3. Installing the crankshaft rear seal housing assembly using an alignment tool and tightening setscrews to the specified torque.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...fusjekkdmdmd2w
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures involving draining fluids, removing fittings and plates, using pullers to remove bearings, and disassembling springs, pistons, and other internal parts while taking safety precautions for released pressures. Detailed illustrations supplement each step.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, seals, and bearings. It then details 19 additional steps to disassemble the travel motor and counterbalance valve, removing pistons, plates, springs, and seals. Personal injury warnings are included to release pressures and spring forces safely when disassembling components.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
The document provides disassembly instructions for the final drive, travel motor, counterbalance valve, and other components of excavator models 313D2 and 313D2 GC. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, pistons, springs, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, and counterbalance valve housing. Safety warnings are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers, and spanner wrenches.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
This document provides instructions for removing and installing the front gear group on a Caterpillar 312E or 312E L excavator engine. The removal procedure involves using tools to lock the crankshaft, camshaft, and fuel injection pump in position before loosening threaded inserts on the rocker arms. Several gears and other components are then removed from the front of the engine housing. The installation procedure outlines cleaning and inspecting parts before reinstalling components in reverse order, maintaining proper positioning and locking of internal components.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...fusjekkdmdmd2w
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening the bolts to the specified torque.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing the crankshaft rear seal housing assembly using alignment tools and tightening the setscrews in a specific order to the specified torque.
- Removing and installing an optional crankshaft wear sleeve using pullers and installer/locator tools, to re
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...fusjekkdmdmd2w
The documents provide instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
1. Installing the flywheel, which involves heating the ring gear, cleaning parts, using guide bolts and lifting devices, and tightening bolts to the specified torque.
2. Removing the crankshaft rear seal, which is non-serviceable, requiring replacement of the entire housing assembly after removing setscrews.
3. Installing the crankshaft rear seal housing assembly using an alignment tool and tightening setscrews to the specified torque.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...fusjekkdmdmd2w
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...fusjekkdmdmd2w
This document provides disassembly instructions for the final drive, travel motor, and other components of a 312D2 L excavator. It lists the required tools and outlines 23 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and traction control valve. Safety notices are included throughout to warn of potential injuries from parts under spring pressure or hydraulic oil.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...fusjekkdmdmd2w
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:14:12 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:15:12 UTC+0800 2020
2/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00608136
1. Loosen the hose clamp (1) on hose (2) .
2. Remove hose (2) from the turbocharger (3) .
Illustration 2 g00812846
3. Disconnect oil supply line (4) from the cylinder block.
4. Loosen two clamps (5) on hose (7) .
5. Slide hose (7) off fitting (8) onto oil return line (6) .
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00608177
6. Remove eight nuts (9) from the studs on the exhaust manifold.
Note: The four studs have two nuts for a total of eight nuts.
7. Remove turbocharger (3), oil supply line (4), and oil return line (6) as an unit.
8. Remove metal gasket (10) (not shown). Check the gasket for wear or damage. Replace the
gasket, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:16:11 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615171
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
Illustration 1 g00608212
2. Remove two bolts (1) from the oil return line. Remove bolt (2) from the oil supply line.
3. Remove oil return line (3) from the cartridge.
4. Remove oil supply line (4) from the cartridge.
Illustration 2 g00608210
5. Remove gasket (5) from the cartridge.
6. Remove gasket (6) from the turbine housing.
2/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00608342
7. Remove the bolt and nut (7) from clamp (8). Remove clamp (8) that secures the turbine
housing (9) to the cartridge (10) .
8. Separate turbine housing (9) from the cartridge (10) .
Illustration 4 g00608415
Illustration 5 g00608452
3/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 9. Remove snap ring (11) from compressor housing (12) .
10. Separate compressor housing (12) from the cartridge (10) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:17:10 UTC+0800 2020
4/4
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01147762
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During the assembly procedure, ensure that the index marks are aligned when the
components are assembled.
Illustration 1 g00608452
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00608415
1. Install cartridge (10) into compressor housing (12) .
2. Install snap ring (11) into compressor housing (12) .
Illustration 3 g00608342
3. Install cartridge (10) into turbine housing (9) .
4. Install clamp (8) that secures cartridge (10) and turbine housing (9) together. Install the bolt
and nut (7) into clamp (8).
Note: Refer to the Specifications Module, "Turbocharger" for information on the clamp.
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00608210
5. Inspect the condition of the gaskets. Replace the gaskets, if necessary.
6. Install gasket (6) on the turbine housing.
7. Install gasket (5) on the cartridge.
Illustration 5 g00608212
8. Place oil supply line (4) in position. Secure the oil supply line with bolt (2) (not shown).
9. Place oil return line (3) in position. Secure the oil return line with two bolts (1) .
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:18:09 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564587
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of all gaskets. Replace the gaskets, if necessary.
Illustration 1 g00608177
1/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil
return line (6) (not shown) as a unit.
3. Install eight nuts (9). Tighten the nuts to a torque of 41 N·m (30 lb ft).
Note: Two nuts are installed on each turbocharger mounting stud.
Illustration 2 g00812846
4. Slide hose (7) down the oil return line (6) onto fitting (8) .
5. Tighten two clamps (5) on hose (7) .
6. Connect oil supply line (4) to the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:19:09 UTC+0800 2020
2/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565722
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00605454
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2. Remove exhaust manifold (2) from the cylinder head assembly.
3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the
cylinder head assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00605454
1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head
assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
2. Place exhaust manifold (2) in position on the cylinder head.
3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:20:08 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615211
Air Inlet Heater - Remove and Install
SMCS - 1090-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611147
1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) .
2. Disconnect air inlet hose (2) from air inlet elbow (4) .
1/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 3. Remove four bolts (3) and washers that secure the following items to the air inlet manifold:
air inlet elbow (4), gasket (5), air inlet heater (6) and gasket (7) .
Illustration 2 g00611165
4. Remove the following items from the air inlet manifold: air inlet elbow (4), gasket (5), air
inlet heater (6) and gasket (7) .
Note: Check the condition of the gaskets that are used between the elbow and the air inlet
heater. Check the gaskets between the air inlet heater and the air inlet manifold. If the
gaskets are damaged in any way, replace the gaskets.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g00611165
Note: Check condition of the gaskets for the air inlet elbow and the air inlet heater. If the
gaskets are damaged, use a new part for replacement. The wire mesh gasket (7) is installed
between the air inlet manifold and the air inlet heater.
1. Place the following items in position on the air inlet manifold: gasket (7), the air inlet heater
(6), gasket (5) and the air inlet elbow (4) .
Illustration 4 g00611147
2. Install four bolts (3) that secure the following items to the air inlet manifold: gasket (7), the
air inlet heater (6), gasket (5) and the air inlet elbow (4)
Tighten bolts (3) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
3. Connect air inlet hose (2) to air inlet elbow (4) .
4. Tighten hose clamp (1) that secures the air inlet hose to the air inlet elbow.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:21:08 UTC+0800 2020
3/3
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01575215
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
A. Remove fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
B. Remove fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
C. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...