The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. The installation procedure specifies cleaning the crankshaft and pulley, applying retaining compound, and pressing the pulley onto the crankshaft with an installer tool. Torque specifications are provided for securing bolts during reinstallation.
Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh0000...fjskkksmemm
The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Removing and installing the flywheel, which requires drilling holes in the crankshaft rear seal before removal.
- Removing the crankshaft rear seal and wear sleeve using slide hammer and seal distorter tools.
- Installing a new crankshaft rear seal and wear sleeve using an installer tool and retaining compound.
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve using a chisel if needed.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...hvy7sbkw8e
This document provides instructions for installing and removing various engine components on Caterpillar 320C excavators, including:
- Installing the flywheel by attaching it with bolts and checking runout.
- Removing and installing the crankshaft rear seal using tools like a slide hammer and installer.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal.
- Procedures for the crankshaft pulley which involves removing nuts and a wear sleeve, and installing with a torque wrench.
- Removing the crankshaft front seal using a slide hammer puller.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including:
1. Removing and installing the flywheel, which involves using straps and lifting devices to handle the 50 kg flywheel, and torquing bolts to 83 Nm.
2. Removing and installing the crankshaft rear seal, using tools to drill holes, pull out the old seal, and install the new seal and wear sleeve.
3. Removing and installing the flywheel housing, which requires lifting devices due to its 65 lb weight, replacing seals, and torquing bolts.
4. Removing and installing the crankshaft pulley, which begins
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...xiapokang564341
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar cat 312 c l excavator (prefix bwh) service repair manual (bwh0000...fjskkksmemm
The document provides instructions for removing and installing various engine components on a Caterpillar 312C excavator, including:
- Removing and installing the flywheel, which requires drilling holes in the crankshaft rear seal before removal.
- Removing the crankshaft rear seal and wear sleeve using slide hammer and seal distorter tools.
- Installing a new crankshaft rear seal and wear sleeve using an installer tool and retaining compound.
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve using a chisel if needed.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...hvy7sbkw8e
This document provides instructions for installing and removing various engine components on Caterpillar 320C excavators, including:
- Installing the flywheel by attaching it with bolts and checking runout.
- Removing and installing the crankshaft rear seal using tools like a slide hammer and installer.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal.
- Procedures for the crankshaft pulley which involves removing nuts and a wear sleeve, and installing with a torque wrench.
- Removing the crankshaft front seal using a slide hammer puller.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including:
1. Removing and installing the flywheel, which involves using straps and lifting devices to handle the 50 kg flywheel, and torquing bolts to 83 Nm.
2. Removing and installing the crankshaft rear seal, using tools to drill holes, pull out the old seal, and install the new seal and wear sleeve.
3. Removing and installing the flywheel housing, which requires lifting devices due to its 65 lb weight, replacing seals, and torquing bolts.
4. Removing and installing the crankshaft pulley, which begins
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...xiapokang564341
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove components and clean surfaces, and installing replacement parts with adhesives or by pressing/bolting into place. Safety notices are provided to handle parts carefully and contain fluids.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, provide notices about cleanliness and fluid containment, and note related removal and installation steps for other components.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...ufjksemd8ujd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and seals, and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and sockets, which may require removing a wear sleeve.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal.
- Installing a new crankshaft front seal using a installer tool and applying oil to the seal and crankshaft pulley.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...ufjksemd8ujd
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump in position using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...ufjksemd8ujd
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to clearly show how to disassemble the various systems.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...ufjksemd8ujd
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening bolts to specification.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing a crankshaft rear seal housing assembly using alignment tools and tightening setscrews in a specific order.
- Removing and installing a crankshaft wear sleeve using pullers and installation sleeves to reclaim worn seal surfaces.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...ufjksemd8ujd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It includes:
1) Heating the ring gear to install it on the flywheel, then installing the flywheel using guide bolts and tightening bolts to the specified torque.
2) Removing the crankshaft rear seal housing assembly by removing setscrews, as the seal is non-serviceable and the housing must be replaced.
3) Installing the new crankshaft rear seal housing assembly by positioning it over the crankshaft, aligning it, and tightening setscrews to the specified torque using an alignment tool.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...ufjksemd8ujd
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in a specific sequence, and refilling fluids before installing removed components.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...ufjksemd8ujd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling the components. Safety notices are included to warn of potential injuries from parts under spring pressure, hydraulic oil pressure, and hot oil. The components are to be marked for proper reassembly.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, the new seal assembly is pushed onto the crankshaft flange with a plastic sleeve for protection. Setscrews are then tightened to secure the housing assembly to the cylinder block. Proper cleaning, alignment with tools, and torque specifications are emphasized to complete the process.
This document provides instructions for removing and installing various components of a Caterpillar 312D excavator engine, including:
- Removing and installing the flywheel housing, which requires lifting devices and bolts.
- Removing and installing the crankshaft rear seal, using a slide hammer, distorter, and installer tool.
- Removing and installing the crankshaft pulley, using a combination puller and socket tools. Heating may be required to install wear sleeves.
- Guidelines are provided for cleaning parts and applying retaining compounds during installation. Torque specifications and required tools are listed for each procedure.
The document provides instructions for installing a flywheel on a 3054C engine. It includes the following steps:
1. Clean the flywheel housing and inspect the crankshaft rear seal for leaks.
2. Heat the ring gear to 250°C and quickly install it on the flywheel, ensuring correct orientation.
3. Install guide bolts and lifting brackets to position the flywheel, then install and tighten the bolts to the specified torque.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...ufjksemd8ujd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and seals, and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and sockets, which may require removing a wear sleeve.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal.
- Installing a new crankshaft front seal using a installer tool and applying oil to the seal and crankshaft pulley.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...ufjksemd8ujd
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump in position using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...ufjksemd8ujd
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to clearly show how to disassemble the various systems.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...ufjksemd8ujd
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening bolts to specification.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing a crankshaft rear seal housing assembly using alignment tools and tightening setscrews in a specific order.
- Removing and installing a crankshaft wear sleeve using pullers and installation sleeves to reclaim worn seal surfaces.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...ufjksemd8ujd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It includes:
1) Heating the ring gear to install it on the flywheel, then installing the flywheel using guide bolts and tightening bolts to the specified torque.
2) Removing the crankshaft rear seal housing assembly by removing setscrews, as the seal is non-serviceable and the housing must be replaced.
3) Installing the new crankshaft rear seal housing assembly by positioning it over the crankshaft, aligning it, and tightening setscrews to the specified torque using an alignment tool.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...ufjksemd8ujd
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in a specific sequence, and refilling fluids before installing removed components.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...ufjksemd8ujd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling the components. Safety notices are included to warn of potential injuries from parts under spring pressure, hydraulic oil pressure, and hot oil. The components are to be marked for proper reassembly.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, the new seal assembly is pushed onto the crankshaft flange with a plastic sleeve for protection. Setscrews are then tightened to secure the housing assembly to the cylinder block. Proper cleaning, alignment with tools, and torque specifications are emphasized to complete the process.
This document provides instructions for removing and installing various components of a Caterpillar 312D excavator engine, including:
- Removing and installing the flywheel housing, which requires lifting devices and bolts.
- Removing and installing the crankshaft rear seal, using a slide hammer, distorter, and installer tool.
- Removing and installing the crankshaft pulley, using a combination puller and socket tools. Heating may be required to install wear sleeves.
- Guidelines are provided for cleaning parts and applying retaining compounds during installation. Torque specifications and required tools are listed for each procedure.
The document provides instructions for installing a flywheel on a 3054C engine. It includes the following steps:
1. Clean the flywheel housing and inspect the crankshaft rear seal for leaks.
2. Heat the ring gear to 250°C and quickly install it on the flywheel, ensuring correct orientation.
3. Install guide bolts and lifting brackets to position the flywheel, then install and tighten the bolts to the specified torque.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:09:21 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:11:20 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:12:19 UTC+0800 2020
3/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:13:19 UTC+0800 2020
4/4
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:14:18 UTC+0800 2020
2/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 18 23:15:17 UTC+0800 2020
2/2
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 5 g00611573
5. The following items are components of Tool (A) .
◦ 9U-6147 Stud (6)
◦ 6V-8231 Nut (7)
◦ 9U-6146 Sleeve Assembly (8)
◦ 8T-4244 Nut (9)
6. Use Tool (A) and remove idler shaft (5) from the cylinder block. Check the idler shaft for
wear and damage. Replace the shaft, if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump - Remove".
• In order to remove the gear from the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft gear, refer to Disassembly and Assembly, "Crankshaft
Gear - Remove and Install".
4/5
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR BWH
Configuration: 312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615420
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00611570
1. Use Tool (A) to install a new bushing (4) (not shown), if the bushing was removed.
Illustration 2 g00611572
2. Install idler shaft (5) onto the cylinder block.
Note: When the idler shaft is installed, ensure that the oil hole of the shaft is up. If
necessary, cool the idler shaft to 0 °C (32 °F) before installation. The temperature of the
idler shaft is lowered in order to ease the installation of the idler shaft.
Illustration 3 g00611569
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection
drive gear with the "33" mark with the "3" mark on idler gear. Make an alignment of the "2"
mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the
crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center
position when these marks are in alignment.
3. Install idler gear (3) onto the idler shaft.
2/3
312C & 312C L Excavators BWH00001-UP (MACHINE) POWERED BY 3064 Engi...
2020/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...