The document provides disassembly and assembly instructions for the final drive of a 312B excavator. It consists of 47 steps to disassemble the final drive and 18 steps to reassemble it. The disassembly process involves removing components like the travel motor, brake assembly, piston, links, gears, seals, and bearings. The assembly process reverses this by installing new seals and bearings, and reinstalling the removed components in the reverse order. Precision tools are required for tasks like compressing springs, removing snap rings, and checking assembled heights.
Caterpillar cat 312 b excavator (prefix 9nw) service repair manual (9nw00001 ...fjsekksmemm
This document provides instructions for disassembling and assembling the final drive of a Caterpillar 312B excavator. The disassembly process involves 47 steps to remove components like the brake assembly, planetary gears, seals, and bearings. The assembly follows the reverse order, noting that specific tools are required to reinstall components like the spindle nut which requires 1500 Nm of torque. The summary provides an overview while focusing on the key steps and components involved in the process.
Caterpillar cat 312 b l excavator (prefix 9nw) service repair manual (9nw0000...fjskkksmemm
The document provides instructions for disassembling and assembling the final drive of a 312B excavator. Some key steps include:
1. Removing the final drive and travel motor and disassembling components like springs, pistons, disks, gears, and seals.
2. Using various tools to remove parts like retaining rings, snap rings, nuts, and shafts.
3. Inspecting and repairing parts as needed before assembly.
4. Reassembling components in reverse order and verifying clearances and heights using tools like dial indicators.
The document provides instructions for disassembling and assembling the final drive of a 312B excavator. It lists 47 steps to fully disassemble the final drive including removing gears, shafts, seals, and other components. The assembly procedure is described in reverse order and includes installing new seals, bearings, and torquing fasteners to the specified values. Tools required are listed to complete both the disassembly and assembly processes.
The document provides instructions for disassembling and assembling the final drive of a 312B excavator. It lists 47 steps to fully disassemble the final drive including removing gears, shafts, seals, and other components. The assembly procedure is described in reverse order and requires specific tools including a repair stand, crossblock, push-puller plates, spring compressor plates, internal pliers, link brackets, and torque wrenches. Thorough cleaning is important before disassembly and assembly to ensure proper reinstallation of parts.
This document provides instructions for disassembling and assembling the final drive of a 312B excavator. The disassembly process involves 47 steps to remove components like the brake assembly, planetary gears, spindle nut, and seals. The assembly process reverses the disassembly with 13 steps, including installing new seals and checking spindle nut alignment using indicators. Tools required include a repair stand, pullers, pliers, and torque wrench.
Caterpillar Cat 312C L Excavator (Prefix CBT) Service Repair Manual (CBT00001...tuzhiyou2
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps to fully disassemble the older style swing drive. These include removing the sun gear, carrier assembly, planetary shafts, bearings, and housing components. Reassembly is described in 17 steps, covering pressing components back together and installing seals, washers, and fasteners using specific tools. The level of detail provided aims to fully disassemble and reassemble the swing drive system.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps to fully disassemble the older style swing drive. These include removing the sun gear, carrier assembly, planetary shafts, bearings, and housing components. Reassembly is the reverse of disassembly, applying sealant or locking agents as needed and torquing fasteners to specifications. The process is similar for the newer swing drive style, involving removing over 15 parts across 14 illustrated steps.
Caterpillar Cat 312C L Excavator (Prefix CBT) Service Repair Manual (CBT00001...qfyc504378
This document provides instructions for disassembling and assembling the swing drive of a 312C excavator. The disassembly procedure involves using tools to remove over 20 individual parts from the carrier assembly, planetary gears, and housing. The assembly procedure instructs cleaning and applying sealant to parts before installing components in reverse order, such as pressing bearings onto shafts and installing cups into the housing. Proper cleaning and application of sealant to mating surfaces is emphasized to prevent contamination.
Caterpillar cat 312 b excavator (prefix 9nw) service repair manual (9nw00001 ...fjsekksmemm
This document provides instructions for disassembling and assembling the final drive of a Caterpillar 312B excavator. The disassembly process involves 47 steps to remove components like the brake assembly, planetary gears, seals, and bearings. The assembly follows the reverse order, noting that specific tools are required to reinstall components like the spindle nut which requires 1500 Nm of torque. The summary provides an overview while focusing on the key steps and components involved in the process.
Caterpillar cat 312 b l excavator (prefix 9nw) service repair manual (9nw0000...fjskkksmemm
The document provides instructions for disassembling and assembling the final drive of a 312B excavator. Some key steps include:
1. Removing the final drive and travel motor and disassembling components like springs, pistons, disks, gears, and seals.
2. Using various tools to remove parts like retaining rings, snap rings, nuts, and shafts.
3. Inspecting and repairing parts as needed before assembly.
4. Reassembling components in reverse order and verifying clearances and heights using tools like dial indicators.
The document provides instructions for disassembling and assembling the final drive of a 312B excavator. It lists 47 steps to fully disassemble the final drive including removing gears, shafts, seals, and other components. The assembly procedure is described in reverse order and includes installing new seals, bearings, and torquing fasteners to the specified values. Tools required are listed to complete both the disassembly and assembly processes.
The document provides instructions for disassembling and assembling the final drive of a 312B excavator. It lists 47 steps to fully disassemble the final drive including removing gears, shafts, seals, and other components. The assembly procedure is described in reverse order and requires specific tools including a repair stand, crossblock, push-puller plates, spring compressor plates, internal pliers, link brackets, and torque wrenches. Thorough cleaning is important before disassembly and assembly to ensure proper reinstallation of parts.
This document provides instructions for disassembling and assembling the final drive of a 312B excavator. The disassembly process involves 47 steps to remove components like the brake assembly, planetary gears, spindle nut, and seals. The assembly process reverses the disassembly with 13 steps, including installing new seals and checking spindle nut alignment using indicators. Tools required include a repair stand, pullers, pliers, and torque wrench.
Caterpillar Cat 312C L Excavator (Prefix CBT) Service Repair Manual (CBT00001...tuzhiyou2
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps to fully disassemble the older style swing drive. These include removing the sun gear, carrier assembly, planetary shafts, bearings, and housing components. Reassembly is described in 17 steps, covering pressing components back together and installing seals, washers, and fasteners using specific tools. The level of detail provided aims to fully disassemble and reassemble the swing drive system.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps to fully disassemble the older style swing drive. These include removing the sun gear, carrier assembly, planetary shafts, bearings, and housing components. Reassembly is the reverse of disassembly, applying sealant or locking agents as needed and torquing fasteners to specifications. The process is similar for the newer swing drive style, involving removing over 15 parts across 14 illustrated steps.
Caterpillar Cat 312C L Excavator (Prefix CBT) Service Repair Manual (CBT00001...qfyc504378
This document provides instructions for disassembling and assembling the swing drive of a 312C excavator. The disassembly procedure involves using tools to remove over 20 individual parts from the carrier assembly, planetary gears, and housing. The assembly procedure instructs cleaning and applying sealant to parts before installing components in reverse order, such as pressing bearings onto shafts and installing cups into the housing. Proper cleaning and application of sealant to mating surfaces is emphasized to prevent contamination.
Fiat Kobelco SL30B Skid Steer Loader Service Repair Manual.pdfprmy389342
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- The manual outlines many safety rules for operating the loader safely, such as wearing protective equipment, not allowing passengers, and ensuring all equipment is lowered before servicing.
- It provides standard torque specifications for various types of hardware including decimal, metric, and hydraulic fittings to ensure correct tightening of components.
- The manual is organized into tabs covering general information, engines, fuel system, electrical systems, power train, hydraulics, and mounted equipment. Each tab contains an index of relevant sections.
- Sections provide instructions
Fiat Kobelco EX95W Mini Wheel Excavator Service Repair Manual.pdfprmy389342
This document provides safety precautions for operating an excavator. It advises reading the operator's manual carefully before starting or using the machine. Operators should be familiar with all safety signs and their meanings. Only authorized personnel should operate the machine. Personal protective equipment such as hard hats and safety glasses should always be worn. The operator's compartment and controls should be kept clean. Operators should not jump on or off the machine and should keep hands and feet inside the cab at all times. The machine should come to a complete stop before the operator exits. Height, width and weight limitations of the work site must be assessed. Underground utilities should be located and marked before digging.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfprmy389342
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, covers, fasteners, and guards. The parts are organized with an index and diagram to allow technicians to easily find replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown LP3010 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdfprmy389342
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels, disconnecting batteries, and checking for fuel leaks before working.
2. Procedures for lifting parts of the forklift like the drive wheels or rear, including using blocks and jacks of adequate capacity.
3. Chain securing an upright carriage when raised and shipping tie-down instructions.
Clark EPX 16-20S Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages in the manual and on trucks to understand hazards.
2. Recommended safe maintenance practices such as properly ventilating work areas, using fire protection equipment, and disconnecting batteries before working on electrical systems.
3. Procedures for safely lifting, jacking, and blocking forklifts, including raising the drive wheels, upright, and entire truck, to access components for repair work.
Clark CMP 70 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 60 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...prmy389342
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure cleanliness when handling engine parts.
Fiat Kobelco SL30B Skid Steer Loader Service Repair Manual.pdfprmy389342
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- The manual outlines many safety rules for operating the loader safely, such as wearing protective equipment, not allowing passengers, and ensuring all equipment is lowered before servicing.
- It provides standard torque specifications for various types of hardware including decimal, metric, and hydraulic fittings to ensure correct tightening of components.
- The manual is organized into tabs covering general information, engines, fuel system, electrical systems, power train, hydraulics, and mounted equipment. Each tab contains an index of relevant sections.
- Sections provide instructions
Fiat Kobelco EX95W Mini Wheel Excavator Service Repair Manual.pdfprmy389342
This document provides safety precautions for operating an excavator. It advises reading the operator's manual carefully before starting or using the machine. Operators should be familiar with all safety signs and their meanings. Only authorized personnel should operate the machine. Personal protective equipment such as hard hats and safety glasses should always be worn. The operator's compartment and controls should be kept clean. Operators should not jump on or off the machine and should keep hands and feet inside the cab at all times. The machine should come to a complete stop before the operator exits. Height, width and weight limitations of the work site must be assessed. Underground utilities should be located and marked before digging.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfprmy389342
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, covers, fasteners, and guards. The parts are organized with an index and diagram to allow technicians to easily find replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown LP3010 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdfprmy389342
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels, disconnecting batteries, and checking for fuel leaks before working.
2. Procedures for lifting parts of the forklift like the drive wheels or rear, including using blocks and jacks of adequate capacity.
3. Chain securing an upright carriage when raised and shipping tie-down instructions.
Clark EPX 16-20S Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages in the manual and on trucks to understand hazards.
2. Recommended safe maintenance practices such as properly ventilating work areas, using fire protection equipment, and disconnecting batteries before working on electrical systems.
3. Procedures for safely lifting, jacking, and blocking forklifts, including raising the drive wheels, upright, and entire truck, to access components for repair work.
Clark CMP 70 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 60 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...prmy389342
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure cleanliness when handling engine parts.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9NW
Configuration: 312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
312B Excavator Machine Systems
Media Number -RENR1113-01 Publication Date -01/06/1999 Date Updated -29/11/2001
i02061750
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Repair Stand 1
B
9S-7338 Crossblock 1
3H-0465 Push-Puller Plate 2
154-9326 Spring Compressor Plate 1
154-9323 Spacer 2
C 5P-4758 Internal Pliers 1
D 138-7575 Link Bracket 2
E 1U-5839 Puller 1
F
199-4925
Wrench
(1) 1
165-1670 Wrench 1
165-1671 Reaction Shaft 1
132-8119 Torque Wrench 1
132-8223 110 V Power Pack 1
132-8231 220 V Power Pack 1
1/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. G 154-9315 Thread File 1
( 1 )
Use this wrench for the newer shaft nut that has four slots.
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove" in this
manual.
1. Thoroughly clean the outside of the travel motor and the final drive prior to disassembly.
2. Put an alignment mark across the sections of the travel motor and the final drive for
assembly purposes. The parts must be reinstalled in the original locations of the parts.
Illustration 1 g00526895
3. Fasten the travel motor and the final drive to Tooling (A) with the travel motor in the up
position. Remove drain plugs (1) in order to drain the oil. The capacity of the final drive is
2.5 L (.66 US gal).
Illustration 2 g00526930
4. Remove the bolts (2) and use the lifting strap in order to remove the travel motor from the
final drive.
2/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00527283
5. Use Tooling (B) to compress the brake assembly and remove the retaining ring.
Illustration 4 g00527299
6. Remove spacer ring (3) and twenty springs (4) .
3/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00527333
Typical example
7. Apply a suitable amount of air pressure in the oil passage in order to partially remove piston
(5) .
Illustration 6 g00527337
8. Remove piston (5) .
Illustration 7 g00527353
9. Remove shaft link (6) .
4/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00527355
10. Remove brake disks (7) .
Illustration 9 g00527404
11. Remove supporting ring (8) .
Illustration 10 g00527398
12. Use Tooling (C) to remove snap ring (9) .
5/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 13. Remove seal (10) from spindle (11) .
Illustration 11 g00527410
Typical example
14. Remove seals (12) from piston (5) .
15. Use lifting straps and Tooling (D) in order to lift the final drive off Tooling (A) .
16. Carefully rotate the final drive so that the planetary cover is up.
17. Fasten the final drive to Tooling (A) .
Illustration 12 g00527492
18. Remove twelve bolts (13) that secure cover (14) to the final drive. Remove the O-ring seal
from the cover.
6/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00527496
19. Remove sun gear shaft (15) from the final drive.
Illustration 14 g00527500
20. Remove the first stage of planetary gear assembly (16) from the final drive.
Illustration 15 g00527501
7/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 21. Use snap ring pliers to remove snap ring (17) that secures planetary gear (18) to the
planetary carrier.
Illustration 16 g00527505
22. Use Tooling (E) in order to remove planetary gear (18). Remove the disk from planetary
carrier (19) .
23. Repeat Step 21 and Step 22.
Illustration 17 g00527583
24. Use snap ring pliers to remove snap ring (20) from sun gear (21) .
8/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00527597
25. Remove sun gear (21) from planetary carrier (19) .
Illustration 19 g00527606
26. Remove the second stage of planetary gear assembly (22) from the final drive.
Illustration 20 g00527613
27. Use snap ring pliers to remove snap ring (23) from planetary gear (24) .
9/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00527622
28. Use Tooling (E) to remove planetary gear (24). Remove the disk from planetary carrier
(25) .
29. Repeat Steps 27 and 28 for the other two planetary gears and disks.
Illustration 22 g00527625
30. Use snap ring pliers to remove snap ring (26) from sun gear (27) .
10/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00527629
31. Remove sun gear (27) from planetary carrier (25) .
Illustration 24 g00527656
32. Use snap ring pliers to remove snap ring (28) that secures planetary gear (29) to spindle
(30) .
33. Use Tooling (E) to remove planetary gear (29) from spindle (30) .
34. Repeat Steps 32 and 33 for the other four planetary gears.
11/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 25 g00527840
Illustration 26 g00528079
35. Remove bolt (31), tab (32) and ball (33) from spindle nut (34).
Note: Use the access hole in ring gear (35) to access bolt (31). Ring gear (35) can be rotated
in order to align the access hole with bolt (31) .
12/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 27 g00530820
Note: The procedure for drilling will create a small amount of steel chips. Do not allow the
chips to fall into bearing kit (35) .
36. Use a 4.76 mm (.188 inch) drill bit (41) to remove the damaged portion of threads which
was caused by ball (33). This will require drilling into spindle (30) to a depth of
approximately 1.5 mm (.06 inch).
37. Clear the steel chips from the hole. Do not allow the chips to fall into bearing kit (35) .
38. Repeat Steps 35 through 37 in order to remove the remaining bolt assembly.
Illustration 28 g00527917
39. Install the reaction shaft from Tooling (F) on spindle (30), as shown.
13/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 29 g00527930
40. Install the socket from Tooling (F) over spindle nut (34), as shown.
41. Use Tooling (F) to remove spindle nut (34). The torque that is required to remove the
spindle nut is approximately 1500 N·m (1100 lb ft).
Illustration 30 g00528669
42. Remove bearing kit (35) from spindle (30) .
Note: It may be necessary to remove bearing kit (35) by pulling bearing kit (35) with ring
gear (36) .
14/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 31 g00528772
43. Remove ring gear (36) from spindle (30) .
Illustration 32 g00528781
44. Remove one half of Duo-cone seal kit (37) from ring gear (36) .
Illustration 33 g00528793
45. Remove bearing kit (38) from ring gear (36) .
15/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 34 g00528800
46. Remove the second half of Duo-cone seal kit (37) from spindle (30) .
Illustration 35 g00528814
Typical example
47. Use Tooling (G) to shape spindle threads (39), if the threads appear damaged.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 26 20:01:33 UTC+0800 2020
16/16
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 En...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9NW
Configuration: 312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
312B Excavator Machine Systems
Media Number -RENR1113-01 Publication Date -01/06/1999 Date Updated -29/11/2001
i02061751
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 1P-2420 Repair Stand 1
(B)
9S-7338 Crossblock 1
3H-0465 Push-Puller Plate 2
154-9326 Spring Compressor Plate 1
154-9323 Spacer 2
(C) 5P-4758 Internal Pliers 1
(D) 138-7575 Link Bracket 2
(E) 161-4350 Duo-cone Seal Kit 1
(F)
199-4925
Socket
(1) 1
165-1670 Socket 1
165-1671 Reaction Shaft 1
132-8119 Torque Wrench 1
132-8223 110 V Power Pack 1
132-8231 220 V Power Pack 1
1/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. (G)
6V-3075 Dial Indicator 1
6V-6167 Contact Point 1
3P-1565 Collet Clamp 1
165-8958 Plastic Base for Indicator 1
(H) 165-3977 Punch 1
(J)
155-1709 Hydraulic Test Adapter 1
3J-1907 O-ring Seal 1
6V-3965 Nipple Assembly 1
6V-4143 Coupler Assembly 2
6V-3014 Hose Assembly 1
8T-0855 Pressure Gauge 1
1U-5230 Hand Pump 1
5S-2403 Fitting 1
1S-8937 Valve 1
2D-7325 Tee 1
6V-3966 Nipple Assembly 1
( 1 )
Use this wrench for the newer shaft nut that has four slots.
Note: Make sure that all of the parts of the final drive and the travel motor are thoroughly clean
and free of dirt and debris prior to assembly. Replace all O-ring seals that are used in the final
drive with new O-ring seals. Reassemble the final drive and the travel motor on Tooling (A) .
Illustration 1 g00581889
2/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00528800
1. Use Tooling (E) to install one half of Duo-cone seal kit (37) into spindle (30). Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install" in this manual.
2. Put a mark (40) on spindle (30). The mark indicates the position of the original balls (33).
The mark is used in Step 18.
Illustration 3 g00581916
3. Use Tooling (G) to check assembled height (X) in at least four places at 90 degree intervals.
The difference in height around the ring must not be more than 1.0 mm (.04 inch).
3/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 4 g00528793
4. Install bearing kit (38) into ring gear (36) .
Note: Check the condition of the bearing kit. If the bearing kit is worn or damaged, use a
new bearing kit.
Illustration 5 g00528781
5. Use Tooling (E) to install the second one half of Duo-cone seal kit (37) into ring gear (36).
Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install" in this
manual.
6. Repeat step 3.
4/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 6 g00528772
7. Install spindle (30) onto Tooling (A) .
Note: Turn over ring gear (36) very carefully. Make sure that Duo-cone seal kit (37) is not
dislodged.
8. Install ring gear (36) onto spindle (30) .
Illustration 7 g00530753
9. Install bearing kit (35) onto spindle (30) .
5/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 8 g00527917
10. Install the reaction shaft from Tooling (F) on spindle (30), as shown.
Illustration 9 g00527930
Note: Lubricate the threads with oil before installation. Use caution. The threads are easy to
cross thread.
11. Install spindle nut (34) onto spindle (30) .
12. Install the socket from Tooling (F) on spindle nut (34) .
Note: Rotate the spindle in one direction during the tightening procedure in order to seat the
bearings properly.
13. Use Tooling (F) to tighten spindle nut (34) to a torque of 1500 N·m (1100 lb ft).
14. Mark spindle nut (34) in relation to spindle (30) .
Note: Do not confuse this mark with mark (40) for the location of balls (33) .
15. Tighten spindle nut (34) to a torque of 2500 N·m (1840 lb ft).
16. Loosen spindle nut (34) so that the mark on the spindle nut is 5 to 10 degrees from the mark
on the spindle.
6/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 17. Tighten spindle nut (34) to a torque of 1500 N·m (1100 lb ft).
Illustration 10 g00530793
18. Measure the distance from the new bolt (31) to mark (40). The distance must be at least 10
mm (.4 inch). If the distance is less than 10 mm (.4 inch), use a new spindle nut (34) .
Illustration 11 g00581917
19. Use Tooling (H) to peen the threads of spindle (30) .
7/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 12 g00528079
20. Install bolt (31), tab (32) and ball (33) into spindle nut (34). Tighten bolt (31) to a torque of
8.5 N·m (6 lb ft).
Note: Use the access hole in ring gear (35) to install bolt (31). Ring gear (35) can be rotated
in order to align the access hole with bolt (31) .
Note: Bend the long tab on tab (32) over the "ear" of ring gear (35). Bend the short tab of
tab (32) over bolt (31) .
21. Repeat step 19 and step 20 in order to install the remaining bolt assembly.
8/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 13 g00527656
22. If necessary, heat gears (29) to 135 °C (275 °F). Install gears (29) on spindle (30). Use snap
ring pliers to install snap ring (28) that secures planetary gear (29) to spindle (30) .
Illustration 14 g00527629
23. Install sun gear (27) into planetary carrier (25) .
Illustration 15 g00527625
24. Use snap ring pliers to install snap ring (26) on sun gear (27) .
9/18
312B & 312B L Excavators 9NW00001-UP (MACHINE) POWERED BY 3054 Engin...
2020/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...