The document provides instructions for servicing a water pump on a Caterpillar 312B L excavator engine:
1) It describes removing the water pump by draining coolant and removing four bolts.
2) Disassembly steps include using tools to remove the pulley, flange, retaining ring, and internal components from the pump housing.
3) Assembly is the reverse of disassembly, checking components for wear and installing in the correct orientation using presses and tools.
Caterpillar cat 312 b l excavator (prefix 8jr) service repair manual (8jr0000...fjsekksmemm
The document provides instructions for servicing components of the engine oil pump and water pump on Caterpillar 312B and 312B L excavators. It describes how to disassemble, inspect, and replace worn parts on both pumps. Specific steps include removing seals, gears, and housings using various tools and ensuring proper installation of new parts in the correct orientation. Technicians are advised to keep areas clean and take safety precautions like wearing gloves when handling heated parts.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller, bearings, and seal.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by installing the seal, bearings, impeller, shaft assembly, flange, retaining ring, and pulley.
4. Install the serviced water pump back onto the engine and refill the cooling system.
Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001...tuzhiyou2
The document provides instructions for servicing the water pump of a Caterpillar 3064 engine. It describes how to disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components. It then explains how to inspect and replace worn parts before reassembling the water pump with the shaft, impeller, bearings, seal and other components replaced as needed. The instructions are intended to guide maintenance technicians in properly servicing the engine's water pump.
Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001...qfyc504378
The document provides instructions for servicing the water pump of a Caterpillar 3064 engine. It describes how to disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components. It then explains how to inspect and replace worn parts before reassembling the water pump with the shaft, impeller, bearings, seal and other components replaced as needed. The instructions are intended to guide maintenance technicians in properly servicing the engine's water pump.
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by reversing the disassembly steps and ensuring proper installation of seals and bearings.
4. Install the serviced water pump back onto the engine block.
Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001...lituo39419496
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller, bearings, and seal.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by installing the seal, bearings, impeller, shaft assembly, flange, retaining ring, and pulley.
4. Install the serviced water pump back onto the engine and refill the cooling system.
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by reversing the disassembly steps and ensuring proper installation of seals and bearings.
4. Install the serviced water pump back onto the engine block.
Caterpillar cat 312 b l excavator (prefix 8jr) service repair manual (8jr0000...fjsekksmemm
The document provides instructions for servicing components of the engine oil pump and water pump on Caterpillar 312B and 312B L excavators. It describes how to disassemble, inspect, and replace worn parts on both pumps. Specific steps include removing seals, gears, and housings using various tools and ensuring proper installation of new parts in the correct orientation. Technicians are advised to keep areas clean and take safety precautions like wearing gloves when handling heated parts.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller, bearings, and seal.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by installing the seal, bearings, impeller, shaft assembly, flange, retaining ring, and pulley.
4. Install the serviced water pump back onto the engine and refill the cooling system.
Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001...tuzhiyou2
The document provides instructions for servicing the water pump of a Caterpillar 3064 engine. It describes how to disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components. It then explains how to inspect and replace worn parts before reassembling the water pump with the shaft, impeller, bearings, seal and other components replaced as needed. The instructions are intended to guide maintenance technicians in properly servicing the engine's water pump.
Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001...qfyc504378
The document provides instructions for servicing the water pump of a Caterpillar 3064 engine. It describes how to disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components. It then explains how to inspect and replace worn parts before reassembling the water pump with the shaft, impeller, bearings, seal and other components replaced as needed. The instructions are intended to guide maintenance technicians in properly servicing the engine's water pump.
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by reversing the disassembly steps and ensuring proper installation of seals and bearings.
4. Install the serviced water pump back onto the engine block.
Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001...lituo39419496
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller, bearings, and seal.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by installing the seal, bearings, impeller, shaft assembly, flange, retaining ring, and pulley.
4. Install the serviced water pump back onto the engine and refill the cooling system.
These documents provide instructions for servicing the water pump of a Caterpillar 3064 engine. The documents describe how to:
1. Disassemble the water pump by removing the pulley, flange, retaining ring, shaft assembly, impeller and other internal components.
2. Inspect and replace any worn parts during disassembly.
3. Reassemble the water pump by reversing the disassembly steps and ensuring proper installation of seals and bearings.
4. Install the serviced water pump back onto the engine block.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jse7039222
The document provides instructions for installing a cylinder head on a 3054C engine. It lists the required tools which include guide bolts and a degree wheel. The procedure involves installing a new cylinder head gasket on dowels on the cylinder block and lifting the cylinder head into place using guide bolts. Setscrews are then installed in a specific numerical order and coated with oil before being tightened to secure the cylinder head.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...lituo39419496
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
More Related Content
Similar to Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001 and up).pdf
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jse7039222
The document provides instructions for installing a cylinder head on a 3054C engine. It lists the required tools which include guide bolts and a degree wheel. The procedure involves installing a new cylinder head gasket on dowels on the cylinder block and lifting the cylinder head into place using guide bolts. Setscrews are then installed in a specific numerical order and coated with oil before being tightened to secure the cylinder head.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...lituo39419496
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
Similar to Caterpillar Cat 312B L EXCAVATOR (Prefix 8JR) Service Repair Manual (8JR00001 and up).pdf (8)
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146555
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00646132
1. Use Tool (A) to install the front oil seal (8) (not shown).
Illustration 2 g00607962
2. Lower the temperature of the spindle (10). Install spindle (10) and idler gear (11) as an
assembly in the front housing.
Note: The temperature of the spindle is lowered in order to ease the installation of the
spindle in the front housing.
Illustration 3 g00607955
3. Install set screw (9) in the front housing.
2/5
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00607885
4. Lower the temperature of the drive gear assembly. Install drive gear (7) in the front housing.
Note: The temperature of the drive gear assembly is lowered in order to ease the installation
of the drive gear assembly in the front housing.
Illustration 5 g00608012
Always wear protective gloves when handling parts that have been
heated.
3/5
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Heat the oil pump gear up to 180 to 220 °C (356 to 428 °F). Support end (X) of the shaft (7)
(drive gear). Install oil pump gear (6) onto the shaft. The end of the gear (Z) should be flush
with the end of the shaft (Y) .
Illustration 6 g00607770
6. Install driven gear (4) into the front housing (slip fit).
Illustration 7 g00607826
7. Place gasket (3) and cover (2) in position on the front housing.
Note: Ensure that the old gasket material is removed from the mating surfaces.
8. Install the washer and bolt (1) that secures the cover to the front housing. Tighten bolt (1) to
a torque of 34 ± 5 N·m (25 ± 4 lb ft).
Refer to the Specifications Module, "Engine Oil Pump" for more information on the engine oil
pump.
End By: Install the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Install".
4/5
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149671
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
A. Remove V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g00609950
2. Remove four bolts (1) that secure the water pump to the engine.
3. Remove water pump pulley (2) and water pump (3) as an unit from the engine.
4. Remove O-ring (4) (not shown) from water pump (3). Discard the old O-ring.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 22 22:02:27 UTC+0800 2020
2/2
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566087
Water Pump - Disassemble
SMCS - 1361-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Group 1
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
Note: If the water pump is heated up to 80 °C (176 °F), the components can be easily removed.
1/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00610108
1. Remove four bolts (1) and the washers that secure the water pump pulley to the water pump.
2. Remove water pump pulley (2) from the water pump.
Note: Check the groove for the V-belt of the water pump pulley for wear and damage. Replace the
water pump pulley, if necessary.
Note: Use Tool (C) during disassembly procedures of the water pump, which require the use of a
press or a hammer.
Illustration 2 g00610120
3. Use Tool (A) to remove flange (3) from the water pump.
2/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 3 g00610127
4. Use Tool (B) to remove retaining ring (4) from the water pump.
Illustration 4 g00610140
5. Use a press and Tool (C) to remove shaft assembly (5) from water pump assembly (6) .
3/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 5 g00813948
6. Remove impeller (8) from the shaft assembly (5) .
Note: Check the impeller for wear, corrosion, and metal to metal contact. Replace the impeller, if
necessary.
7. Remove the following items from shaft (9) :
◦ Bearing (10)
◦ Spacer (11)
◦ Bearing (12)
◦ Washer (13)
8. Once all of the components have been removed, then check shaft (9) for distortion. Replace the shaft,
if necessary.
9. Check seal (14) for wear and damage. Use Tool (C) in order to remove the seal from the water pump
housing, if necessary.
Note: Replace the seal if any signs of leakage occurs during the operation of the water pump.
10. Replace O-ring (7) with a new O-ring.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 22 22:03:26 UTC+0800 2020
4/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566223
Water Pump - Assemble
SMCS - 1361-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-1861 Retaining Ring Pliers 1
Note: Refer to Specifications, "Water Pump" for specifications that are required during assembly.
1/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00813948
1. Install seal (14), if the seal was removed during the disassembly procedures.
2. The following components are installed on shaft (9) :
◦ Washer (13)
◦ Bearing (12)
◦ Spacer (11)
◦ Bearing (10)
Note: Check two bearings (10) and (12) for correct rotation.
2/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g00610140
3. Use a press and Tool (A) to install shaft assembly (5) into the water pump housing.
4. Use a press and Tool (A) to install impeller (8) onto shaft assembly (5) .
Illustration 3 g00610127
5. Use Tool (B) to install retaining ring (4) into the water pump housing.
6. Use a press and Tool (A) to install flange (3) onto shaft assembly (5) .
Illustration 4 g00610108
3/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 7. Install water pump pulley (2) onto the flange.
8. Install four bolts (1) in order to secure water pump pulley (2) to the flange.
End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 22 22:04:26 UTC+0800 2020
4/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149732
Water Pump - Install
SMCS - 1361-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00609950
1. Replace O-ring (4) (not shown) with a new part. Apply glycerine to the O-ring before the
installation of the water pump (3) and water pump pulley (2) .
1/2
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Install the water pump (3) and water pump pulley (2) as a unit onto the engine.
Note: When the water pump is installed, ensure that the grease fitting is up. Also, ensure
that the weep hole is down.
3. Install bolts (1) in order to secure water pump (3) to the cylinder block.
4. Fill the cooling system to the correct level. Refer to the appropriate Operation and
Maintenance Manual for the correct fluid and the correct filling procedure.
End By: Install V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 22 22:05:25 UTC+0800 2020
2/2
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01148678
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant level below the water temperature regulator.
Illustration 1 g00609693
2. Loosen hose clamp (1) and disconnect hose (2) from cover (4) of the water temperature
regulator.
3. Remove two bolts (3) and the washers from cover (4) of the water temperature regulator.
4. Separate cover (4) from elbow (5) .
5. Remove bolts (6). Separate elbow (5) from the water outlet manifold.
6. Remove water temperature regulator (8) (not shown) from cover (4) .
7. Remove gasket (7) (not shown) and gasket (9) (not shown) from the mounting surfaces of
cover (4) and elbow (5) .
8. Use the following procedure in order to test the water temperature regulator:
a. Put the water temperature regulator in a tub of water. Heat the water in order to test
the water temperature regulator for thermostatic action.
Note: Stir the water in the tub in order to maintain even temperature during the test.
2/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. b. When the valve of the water temperature regulator lifts more than 10 mm (0.4 inch),
measure the water temperature.
Note: The opening temperature for the water temperature regulator is 71° ± 2°C (160°
± 3.6°F).
c. If the valve fails to operate properly, replace the water temperature regulator.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all of the mounting surfaces for the gaskets and remove all gasket material.
NOTICE
If the water temperature regulator is installed incorrectly, it will cause
the engine to overheat.
Illustration 2 g00609693
2. Install water temperature regulator (8) (not shown) into elbow (5) .
Note: When the water temperature regulator is installed, ensure that the hole for the air vent
is up.
3. Install gasket (7) (not shown) and gasket (9) (not shown).
3/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use 8T-9013
Silicone Sealant for replacement.
4. Install the bolts (6) in order to secure elbow (5) to the water outlet manifold.
5. Install cover (4) for the water regulator housing.
6. Install the washers and two bolts (3) in order to secure cover (4) of the water regulator
housing.
7. Reconnect hose (2) and tighten hose clamp (1) onto cover (4) of the water regulator
housing.
8. Fill the cooling system to the correct level. Refer to the Operation and Maintenance Manual
for the correct fluid and the correct filling procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 22 22:06:24 UTC+0800 2020
4/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567208
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing screws M16 X 2 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00605492
1. Remove twelve bolts (1) and washers from the adapter (2) .
2. Remove the adapter (2) from the flywheel housing.
Illustration 2 g00605497
3. Remove four socket head bolts (3) from the inner ring (4) .
4. Remove the inner ring (4) from the flywheel.
2/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00605501
5. Remove six bolts (5) that secure flywheel (6) to the crankshaft. Check all bolts for stripped
threads. Replace the bolts, if necessary.
Illustration 4 g00605504
6. Install Tool (A), a strap, and a suitable lifting device onto the flywheel (6).
7. Use Tool (B) in order to remove the flywheel and ring gear out of the housing. The weight
of the flywheel is 50 kg (110 lb).
8. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 5 g00613038
a. Place the flywheel and ring gear assembly on a suitable support.
Note: Check the flywheel ring gear for the following conditions:cracks, damaged
dowel holes, worn ring gear and damaged ring gear.
Note: Identify the orientation of the old ring gear on the flywheel for proper
positioning, when the new ring gear is installed.
3/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Always wear protective gloves when handling parts that have been
heated.
b. Heat ring gear (7) uniformly.
c. Remove the ring gear (7) by tapping the ring gear all the way around the flywheel
(6) .
d. Reposition the flywheel in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 22 22:07:24 UTC+0800 2020
4/4
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 8JR
Configuration: 312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWERED BY 3064 ENGINE
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
312B & 312B L TRACK-TYPE EXCAVATORS 8JR00001-UP (MACHINE) POWE...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...