This document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 312B EXCAVATOR. It describes:
- Using a strap wrench and removing bolts to detach the oil filter and base from the engine.
- Inspecting seals and replacing if needed before reinstalling the base and filter.
- Removing bolts and washers to detach the oil cooler from the engine block and inspecting seals and gaskets during reinstallation.
- Disassembling the oil cooler by removing nuts and gaskets to separate the core from the cover.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools required are listed. Safety notices warn of hot oil, containing fluids, and disposing of fluids properly.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and washers, checking seals for wear, removing and installing parts, and ensuring cleanliness to prevent contamination. Tools required include a strap wrench and the procedures note containing fluids and disposing of them properly.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools required are listed. Safety notices warn of hot oil, containing fluids, and disposing of fluids properly.
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including:
- Removing and installing the engine oil filter base
- Removing, disassembling, and assembling the engine oil cooler
- Removing and installing the engine oil relief valve
The document contains detailed step-by-step instructions, illustrations, safety notices, and cautions to ensure the work is performed properly. Technicians are directed to contained fluids, clean parts, and follow other best practices.
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including:
- Removing and installing the engine oil filter base
- Removing, disassembling, and assembling the engine oil cooler
- Removing and installing the engine oil relief valve
The document contains detailed step-by-step instructions, illustrations, safety notices, and cautions to ensure the work is performed properly. Technicians are instructed to clean parts, check for damage, and replace worn components as needed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools required are listed. Safety notices warn of hot oil, containing fluids, and disposing of fluids properly.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and washers, checking seals for wear, removing and installing parts, and ensuring cleanliness to prevent contamination. Tools required include a strap wrench and the procedures note containing fluids and disposing of them properly.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools required are listed. Safety notices warn of hot oil, containing fluids, and disposing of fluids properly.
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including:
- Removing and installing the engine oil filter base
- Removing, disassembling, and assembling the engine oil cooler
- Removing and installing the engine oil relief valve
The document contains detailed step-by-step instructions, illustrations, safety notices, and cautions to ensure the work is performed properly. Technicians are directed to contained fluids, clean parts, and follow other best practices.
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including:
- Removing and installing the engine oil filter base
- Removing, disassembling, and assembling the engine oil cooler
- Removing and installing the engine oil relief valve
The document contains detailed step-by-step instructions, illustrations, safety notices, and cautions to ensure the work is performed properly. Technicians are instructed to clean parts, check for damage, and replace worn components as needed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including:
- Removing and installing the engine oil filter base
- Removing, disassembling, and assembling the engine oil cooler
- Removing and installing the engine oil relief valve
The instructions include diagrams to identify the specific components and numbered steps to guide the process. Safety notices are provided throughout to warn of hazards and best practices for containment of fluids.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...fujsjfkkskefsme
This document provides instructions for removing, disassembling, and assembling an engine oil filter base and engine oil cooler on a Caterpillar 321C excavator. The summary is:
1) The instructions describe using a strap wrench and removing bolts to detach the oil filter base and filter from the engine.
2) To disassemble the oil cooler, nuts are removed to separate the core from the cover, and gaskets are checked for wear.
3) Reassembly involves installing new gaskets on the core, securing the core to the cover with nuts, and reinstalling the assembled oil cooler.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...ufjjdkskemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including the engine oil filter base, engine oil cooler, and engine oil relief valve. The procedures describe using specific tools to remove parts like bolts, filters, and bases. Safety notices are included to handle fluids properly and avoid contamination.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...ufjjskekkmde
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including the engine oil filter base, engine oil cooler, and engine oil relief valve. The procedures describe using specific tools to remove parts like bolts, filters, and bases. Safety notices are included to handle fluids properly and avoid contamination.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...jjskefkskemik
This document provides instructions for removing, disassembling, and assembling an engine oil cooler on Caterpillar 3064 and 3066 engines. The removal process involves draining fluids, removing mounting bolts and washers, and checking gaskets and seals. The disassembly separates the oil cooler core from the cover. Assembly installs new gaskets and secures the core and cover with bolts. Safety notices warn of hot fluids and keeping parts clean to prevent damage.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 321C EXCAVATOR. The removal procedure involves taking out the threaded plug, shim, spring and spring seat from the right side of the cylinder block. The installation procedure specifies cleaning all parts and reversing the removal steps. Technicians are advised to inspect parts for wear and replace as needed.
This document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 321C excavator engine. The summary is:
1) The document outlines the required tools and safety procedures for working on the engine.
2) The instructions provide detailed steps for removing the oil filter base, which include using a strap wrench to remove the filter and bolts to remove the base.
3) Similarly, directions are given for removing the engine oil cooler by removing mounting bolts, tubes, and checking seals and gaskets.
4) Reinstallation steps are then described for both the oil filter base and cooler.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 321C EXCAVATOR. The removal procedure involves taking out the threaded plug, shim, spring and spring seat from the right side of the cylinder block. The installation procedure specifies cleaning all parts and reversing the removal steps. Technicians are advised to inspect parts for wear and replace as needed.
This document provides instructions for removing, disassembling, assembling, and installing the engine oil filter base, engine oil cooler, engine oil relief valve, and engine oil bypass valve on a Caterpillar 312 excavator with a 3064 engine. The procedures describe cleaning parts, checking for damage, and securing components with bolts and gaskets in the correct order and torque specifications.
This document provides instructions for removing, disassembling, assembling, and installing the engine oil filter base, engine oil cooler, engine oil relief valve, and engine oil bypass valve on a Caterpillar 312 excavator with a 3064 engine. The procedures describe cleaning parts, checking for damage, applying oil to seals, and torquing bolts to specification.
This document provides instructions for removing, disassembling, assembling, and installing the engine oil filter base, engine oil cooler, engine oil relief valve, and engine oil bypass valve on a Caterpillar 312 excavator with a 3064 engine. The procedures describe cleaning parts, checking for damage, and securing components with bolts and gaskets in the correct order and torque specifications.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
More Related Content
Similar to Caterpillar Cat 312B EXCAVATOR (Prefix 9HR) Service Repair Manual (9HR00001 and up).pdf
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including:
- Removing and installing the engine oil filter base
- Removing, disassembling, and assembling the engine oil cooler
- Removing and installing the engine oil relief valve
The instructions include diagrams to identify the specific components and numbered steps to guide the process. Safety notices are provided throughout to warn of hazards and best practices for containment of fluids.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...fujsjfkkskefsme
This document provides instructions for removing, disassembling, and assembling an engine oil filter base and engine oil cooler on a Caterpillar 321C excavator. The summary is:
1) The instructions describe using a strap wrench and removing bolts to detach the oil filter base and filter from the engine.
2) To disassemble the oil cooler, nuts are removed to separate the core from the cover, and gaskets are checked for wear.
3) Reassembly involves installing new gaskets on the core, securing the core to the cover with nuts, and reinstalling the assembled oil cooler.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...ufjjdkskemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including the engine oil filter base, engine oil cooler, and engine oil relief valve. The procedures describe using specific tools to remove parts like bolts, filters, and bases. Safety notices are included to handle fluids properly and avoid contamination.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...ufjjskekkmde
This document provides instructions for removing and installing various engine components on a Caterpillar 321C EXCAVATOR, including the engine oil filter base, engine oil cooler, and engine oil relief valve. The procedures describe using specific tools to remove parts like bolts, filters, and bases. Safety notices are included to handle fluids properly and avoid contamination.
Caterpillar cat 321 c excavator (prefix dax) service repair manual (dax00001 ...jjskefkskemik
This document provides instructions for removing, disassembling, and assembling an engine oil cooler on Caterpillar 3064 and 3066 engines. The removal process involves draining fluids, removing mounting bolts and washers, and checking gaskets and seals. The disassembly separates the oil cooler core from the cover. Assembly installs new gaskets and secures the core and cover with bolts. Safety notices warn of hot fluids and keeping parts clean to prevent damage.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 321C EXCAVATOR. The removal procedure involves taking out the threaded plug, shim, spring and spring seat from the right side of the cylinder block. The installation procedure specifies cleaning all parts and reversing the removal steps. Technicians are advised to inspect parts for wear and replace as needed.
This document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 321C excavator engine. The summary is:
1) The document outlines the required tools and safety procedures for working on the engine.
2) The instructions provide detailed steps for removing the oil filter base, which include using a strap wrench to remove the filter and bolts to remove the base.
3) Similarly, directions are given for removing the engine oil cooler by removing mounting bolts, tubes, and checking seals and gaskets.
4) Reinstallation steps are then described for both the oil filter base and cooler.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 321C EXCAVATOR. The removal procedure involves taking out the threaded plug, shim, spring and spring seat from the right side of the cylinder block. The installation procedure specifies cleaning all parts and reversing the removal steps. Technicians are advised to inspect parts for wear and replace as needed.
This document provides instructions for removing, disassembling, assembling, and installing the engine oil filter base, engine oil cooler, engine oil relief valve, and engine oil bypass valve on a Caterpillar 312 excavator with a 3064 engine. The procedures describe cleaning parts, checking for damage, and securing components with bolts and gaskets in the correct order and torque specifications.
This document provides instructions for removing, disassembling, assembling, and installing the engine oil filter base, engine oil cooler, engine oil relief valve, and engine oil bypass valve on a Caterpillar 312 excavator with a 3064 engine. The procedures describe cleaning parts, checking for damage, applying oil to seals, and torquing bolts to specification.
This document provides instructions for removing, disassembling, assembling, and installing the engine oil filter base, engine oil cooler, engine oil relief valve, and engine oil bypass valve on a Caterpillar 312 excavator with a 3064 engine. The procedures describe cleaning parts, checking for damage, and securing components with bolts and gaskets in the correct order and torque specifications.
Similar to Caterpillar Cat 312B EXCAVATOR (Prefix 9HR) Service Repair Manual (9HR00001 and up).pdf (11)
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565892
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813775
Illustration 2 g00813789
1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) .
2. Remove the bolts (1) and washers from the engine oil filter base (3) .
3. Remove engine oil filter base (3) from the engine.
2/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
worn or damaged.
Illustration 3 g00813823
5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the
engine.
6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or
damaged.
7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged
components with replacement parts.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:15:10 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565969
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00813823
1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) .
1/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 2 g00813789
2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
damaged.
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
3. Install the O-ring seals (4) on engine oil filter base (3) .
Illustration 3 g00813775
4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers.
5. Install the engine oil filter (2) to the engine oil filter base (3) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:16:09 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615275
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00611319
1. If necessary, remove bolt (1) and the washer from the cylinder head.
2. Remove oil tube assembly (dipstick) (2) from the cylinder block.
3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O-
ring seal is worn or damaged.
Illustration 2 g00611320
4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block.
The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers.
5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block.
Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged.
Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:17:09 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152039
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00618921
Illustration 2 g00611507
1. Remove four nuts (1) and the washers from the oil cooler core (3) .
2. Remove oil cooler core (3) from oil cooler cover (2) .
Note: Check the engine oil cooler core for cracks, clogging, and ruptures.
3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage.
Replace the gaskets, if necessary.
2/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:18:08 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152137
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00618921
Illustration 2 g00611507
1. Install two gaskets (4) onto the oil cooler core (3) .
2. Install the oil cooler cover (2) onto the oil cooler core (3) .
3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover.
4. Tighten the four nuts (1) .
End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:19:07 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615279
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611320
1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces
are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine
cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16
bolts and washers.
1/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00611319
2. Install oil tube assembly (dipstick) (2) into the cylinder block.
Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation.
3. Install bolt (1) and the washer into the cylinder head.
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:20:07 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615285
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607236
1/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g00607247
1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side
of the cylinder block.
2. Remove the spring (3) and spring seat (4) from the cylinder block.
Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the
spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new
part.
Note: Check the cylinder block for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00607247
Illustration 4 g00607236
1. Install spring seat (4) and spring (3) in the cylinder block.
2. Install shim (2) and threaded plug (1) in the cylinder block.
3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb
ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary.
For more information, refer to Specifications, "Engine Oil Relief Valve".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:21:06 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615293
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607679
1/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00607688
1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) .
2. Remove shim (3) from the cylinder block (2) .
3. Remove spring (4) from the cylinder block (2) .
4. Remove spring seat (5) from the cylinder block (2) .
Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the
spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new
part.
Note: Check the cylinder block (2) for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00607688
Illustration 4 g00607679
1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) .
2. Install shim (3) and threaded plug (1) in the cylinder block (2) .
3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary.
For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication
System".
For more information, refer to Specifications, "Engine Oil Bypass Valve".
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 27 10:22:05 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B EXCAVATOR 9HR
Configuration: ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 5 g00607947
8. Use Tool (B) to remove front oil seal (8) (not shown) from the front housing.
Illustration 6 g00607955
Note: Illustration 6 does not show that the front seal (8) is removed.
9. Remove set screw (9) from the front housing.
Illustration 7 g00607962
4/5
ISJ HEX COMMONALITY CHART 9HR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/6/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...