The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse sequence to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02298184
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Drain the coolant from the engine oil cooler into a suitable container for storage or disposal.
Drain the engine oil from the engine oil cooler into a suitable container. Refer to Operation
and Maintenance Manual for the procedure on draining the engine coolant and the engine
oil.
b. Remove the hose from the air filter to the integral air inlet. Refer to the OEM information
for further details.
c. Remove the fuel priming pump. Refer to this Disassembly and Assembly Manual, "Fuel
Priming Pump and Fuel Filter Base - Remove and Install".
d. Remove the pipe for the boost control.
e. Remove the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injection
Nozzles - Remove".
f. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
g. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
h. Remove the glow plugs. Refer to this Disassembly and Assembly Manual, "Glow Plugs -
Remove and Install".
NOTICE
1/4
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the coolant capacity
and the engine oil capacity of the engine.
Illustration 1 g00951472
1. Remove the setscrew (1) and the fuel line from the cylinder head.
2. Disconnect the harness assembly (4) from the coolant temperature sensor.
3. Disconnect tube assembly (5) from the cylinder head.
2/4
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00954953
4. Remove the setscrews (6). Remove the bypass tube (7) from the cylinder head. Remove the
O-ring seals from the bypass tube. Discard the O-ring seals.
Illustration 3 g00951484
5. Gradually loosen the setscrews (8) in reverse numerical order. Refer to Illustration 3. This
will help prevent distortion of the cylinder head.
6. Remove the setscrews (8) from the cylinder head (9).
7. Use a suitable lifting device and carefully lift the cylinder head off the cylinder block. The
weight of the cylinder head is approximately 57 kg (126 lb).
Note: Take care not to damage the machined surfaces of the cylinder head (9) during
removal.
3/4
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: Do not use a lever to separate the cylinder head from the cylinder block.
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
8. Remove the cylinder head gasket. Discard the cylinder head gasket.
Note: Note the location of the dowels on the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 23:00:09 UTC+0800 2020
4/4
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02298802
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
C - Red Rubber Grease -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores, the coolant passages, and the lubricant passages.
Note: Thoroughly clean the hole in the cylinder head for the gas that is ventilated from the
crankcase. Ensure that the hole is not restricted by debris and/or oil deposits.
1/6
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00951564
1. Install the cylinder head gasket on the dowels (10) on top of the cylinder block.
Note: Do not use any sealant or compound on the cylinder head gasket.
2. Install the Tooling (A) in the cylinder block.
3. Use a suitable lifting device to install the cylinder head. The weight of the cylinder head is
approximately 57 kg (126 lb).
Note: Ensure that the cylinder head is positioned on dowels (10). Take care not to damage
the machined surfaces of the cylinder head during installation.
4. Remove the Tooling (A).
Illustration 2 g00951563
2/6
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 5. Clean the threads of the setscrews that secure the cylinder head. Inspect the threads of the
setscrews that secure the cylinder head.
Note: Do not use the setscrews if there is any visual reduction in the diameter of the threads
(Y) that has not been engaged with the cylinder block. Use a straight edge to check the
bolts.
6. Apply clean engine oil to the threads and the shoulder of the setscrews that secure the
cylinder head before installation.
Illustration 3 g00951484
7. Install the setscrews (8) in cylinder head (9).
Note: The short setscrews are installed in holes that are marked 2, 5, 6, 7, 8, 9, and 10.
Note: The long setscrews are installed in holes that are marked 1, 3, and 4.
8. Tighten the setscrews in numerical order to a torque of 50 N·m (37 lb ft). Refer to
Illustration 3.
9. Tighten the setscrews in numerical order to a torque of 100 N·m (74 lb ft). Refer to
Illustration 3.
3/6
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g01151296
10. Use the Tooling (B) to achieve the correct final torque.
Note: If the Tooling (B) is not available, place an index mark on each setscrew.
11. Tighten the setscrews in numerical order. Refer to Illustration 3.
a. Turn the short setscrews (2, 5, 6, 7, 8, 9, and 10) for an additional 225 degrees.
b. Turn the long setscrews (1, 3, and 4) for an additional 270 degrees.
Illustration 5 g00954953
12. Install new O-ring seals on the bypass tube (7). Apply Tooling (C) to the O-ring seals.
Install the bypass tube in the cylinder head. Install the setscrews (6).
4/6
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 6 g00951472
13. Connect the tube assembly (5) to the cylinder head.
14. Connect the harness assembly (4) to the coolant temperature sensor.
15. Install bolt (1) and the fuel line to the cylinder head.
16. Fill the cooling system with coolant. Fill the lubrication system with engine oil.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the cooling
system capacity and the lubrication system capacity of the engine.
End By:
a. Install the glow plugs. Refer to Disassembly and Assembly Manual, "Glow Plugs - Remove
and Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
c. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
d. Install the fuel injection Nozzles. Refer to Disassembly and Assembly Manual, "Fuel
Injection Nozzles - Install".
e. Install the pipe for the boost control.
f. Install the fuel priming pump. Refer to Disassembly and Assembly Manual, "Fuel Priming
Pump and Fuel Filter Base - Remove and Install".
g. Install the hose from the integral air inlet to the air filter. Refer to the OEM information for
further details.
h. Refill the engine with coolant and engine oil. Refer to the Operation and Maintenance
Manual for the correct procedure, the quantities, the coolant specification, and the
specification for the engine oil.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Sat Jun 20 23:01:08 UTC+0800 2020
5/6
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02333592
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00540954
1. Use Tooling (A) to remove lifters (1).
Note: Place an identification mark on the lifters for installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the lifters with clean oil before installing the lifters in the cylinder block.
2/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g00540954
2. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are installed in the original location and that the lifters are
seated correctly.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 23:02:07 UTC+0800 2020
3/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02299051
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
b. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
1/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00951934
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2. Carefully remove camshaft (3) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil prior
to installation.
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Carefully install camshaft (3) in the cylinder block.
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 23:03:07 UTC+0800 2020
3/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02299758
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00546333
Illustration 2 g00546238
1. Use the Tooling (A) in order to remove the camshaft bearing (1) from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00546238
Illustration 4 g00546333
1. Use the Tooling (A) in order to install the camshaft bearing (1) into the bore in the cylinder
block.
Note: Align the oil hole in camshaft bearing (1) with the oil hole in the bore in the cylinder
block.
Note: The camshaft bearing must be inserted until the front edge of the bearing is flush with
the face of the recess in the cylinder block.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 23:04:06 UTC+0800 2020
3/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i05003149
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00956531
1. Remove all dirt, oil, and grease from the exterior surfaces of the oil pan (5).
2. Operate the engine until the engine is warm. Stop the engine.
3. Remove the oil drain plug (6) and the O-ring seal. Drain the engine oil into a suitable
container for storage or disposal.
Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for information
on the capacity of the lubrication system.
Note: Ensure that the engine oil pan is fully supported before the oil pan is removed.
Particular care must be taken with the cast iron version of the engine oil sump as this
version is heavy.
4. Remove the setscrews (3) and the setscrews (4) from the engine oil pan (5).
5. Remove the engine oil pan (5) and remove the gasket (1) from the cylinder block. Discard
the gasket (1).
6. If necessary, remove the nut (2), the seal, and the tube assembly from the engine oil pan.
7. Clean the engine oil pan (5) with a suitable cleaning fluid. Ensure that all of the cleaning
fluid is removed.
Installation Procedure
2/5
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(M8 x 1.25 x 70 mm)
4
B - Loctite 5900 -
C - Loctite 243 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the flange face of the engine oil pan (5) and the flange face of the cylinder block.
Illustration 2 g00541498
2. When the gasket for the oil pan is removed, damage may occur to the existing seal in the
groove of the bridge. If the seal is damaged, apply a sufficient amount of Tooling (B) in
order to fill the groove. The groove must be completely filled.
3. Apply Tooling (B) to the joint between the cylinder block and the front housing.
3/5
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 3 g00956479
4. Install Tooling (A) in the cylinder block in Hole (X).
Note: New setscrews have sealant on the first 13 mm (0.5 inch) of the threads. In order to
reuse the old setscrews, clean the old sealant from the bolts and apply Tooling (C) to the
setscrews.
Note: Ensure that the engine oil pan is properly supported while the engine oil pan (5) is
installed onto the cylinder block.
5. Position a new gasket (1) and the engine oil pan (5) on the cylinder block. Install the
setscrews (3 and 4) in order to secure the engine oil pan to the cylinder block. Tighten the
setscrews finger tight.
6. Remove the Tooling (A) and install the remaining setscrews (3 an 4). Tighten the setscrews
(3) in Hole (Y) to a torque of 22 N·m (16 lb ft).
7. Tighten the remaining setscrews (3 and 4) to a torque of 22 N·m (16 lb ft).
8. Inspect the O-ring for the drain plug (6). Replace the O-ring if it is necessary. Install the O-
ring seal and drain plug (6). Tighten the drain plug to a torque of 34 N·m (25 lb ft).
9. If necessary, install the seal and the tube assembly in the engine oil pan. Tighten the nut (2)
to a torque of 18 N·m (13 lb ft).
10. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.
4/5
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for the
lubrication system capacity of the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 23:05:05 UTC+0800 2020
5/5
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02300831
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...